On Wed, Mar 30, 2011 at 02:02:12PM -0600, Moore, Eric wrote: > Hi Louis, can you send me your /var/log/messages and dmesg output? > Please capture after you've run your test. Hi, My test produces no specific output through dmesg or /var/log/messages as there is no apparent error from the controller. However I can send you the syslog startup output. Let me know if I can run any further tests or provide more information. Thanks, Mar 28 08:19:40 zenon kernel: mpt2sas 0000:02:00.0: PCI INT A -> GSI 41 (level, low) -> IRQ 41 Mar 28 08:19:40 zenon kernel: mpt2sas0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (16423628 kB) Mar 28 08:19:40 zenon kernel: mpt2sas0: IO-APIC enabled: IRQ 41 Mar 28 08:19:40 zenon kernel: mpt2sas0: iomem(0x00000000df2b0000), mapped(0xffffc90000040000), size(65536) Mar 28 08:19:40 zenon kernel: mpt2sas0: ioport(0x000000000000fc00), size(256) Mar 28 08:19:40 zenon kernel: mpt2sas0: sending diag reset !! Mar 28 08:19:40 zenon kernel: mpt2sas0: diag reset: SUCCESS Mar 28 08:19:40 zenon kernel: mpt2sas0: Allocated physical memory: size(3971 kB) Mar 28 08:19:40 zenon kernel: mpt2sas0: Current Controller Queue Depth(1739), Max Controller Queue Depth(2000) Mar 28 08:19:40 zenon kernel: mpt2sas0: Scatter Gather Elements per IO(128) Mar 28 08:19:40 zenon kernel: mpt2sas0: LSISAS2008: FWVersion(09.00.00.00), ChipRevision(0x02), BiosVersion(07.17.00.00) Mar 28 08:19:40 zenon kernel: mpt2sas0: Dell PERC H200 Integrated: Vendor(0x1000), Device(0x0072), SSVID(0x1028), SSDID(0x1F1E) Mar 28 08:19:40 zenon kernel: mpt2sas0: Protocol=(Initiator,Target), Capabilities=(Raid,TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) Mar 28 08:19:40 zenon kernel: mpt2sas0: sending port enable !! Mar 28 08:19:40 zenon kernel: mpt2sas0: host_add: handle(0x0001), sas_addr(0x5842b2b05020c600), phys(8) Mar 28 08:19:40 zenon kernel: mpt2sas0: port enable: SUCCESS Mar 28 08:19:40 zenon kernel: scsi 0:0:0:0: Direct-Access ATA WDC WD1002FAEX-0 1D05 PQ: 0 ANSI: 5 Mar 28 08:19:40 zenon kernel: scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0x4433221103000000), phy(3), device_name(0x4ee25001f42e5a40) Mar 28 08:19:40 zenon kernel: scsi 0:0:0:0: SATA: enclosure_logical_id(0x5842b2b05020c600), slot(0) Mar 28 08:19:40 zenon kernel: scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) Mar 28 08:19:40 zenon kernel: scsi 0:0:0:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1) Mar 28 08:19:40 zenon kernel: scsi 0:0:1:0: Direct-Access ATA WDC WD1002FAEX-0 1D05 PQ: 0 ANSI: 5 Mar 28 08:19:40 zenon kernel: scsi 0:0:1:0: SATA: handle(0x000a), sas_addr(0x4433221102000000), phy(2), device_name(0x4ee25001be5f04eb) Mar 28 08:19:40 zenon kernel: scsi 0:0:1:0: SATA: enclosure_logical_id(0x5842b2b05020c600), slot(1) Mar 28 08:19:40 zenon kernel: scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) Mar 28 08:19:40 zenon kernel: scsi 0:0:1:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1) Mar 28 08:19:40 zenon kernel: scsi 0:0:2:0: Direct-Access ATA WDC WD1002FAEX-0 1D05 PQ: 0 ANSI: 5 Mar 28 08:19:40 zenon kernel: scsi 0:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221101000000), phy(1), device_name(0x4ee250019791af96) Mar 28 08:19:40 zenon kernel: scsi 0:0:2:0: SATA: enclosure_logical_id(0x5842b2b05020c600), slot(2) Mar 28 08:19:40 zenon kernel: scsi 0:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) Mar 28 08:19:40 zenon kernel: scsi 0:0:2:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1) Mar 28 08:19:40 zenon kernel: scsi 0:0:3:0: Direct-Access ATA WDC WD1002FAEX-0 1D05 PQ: 0 ANSI: 5 Mar 28 08:19:40 zenon kernel: scsi 0:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221100000000), phy(0), device_name(0x4ee25001beeb04eb) Mar 28 08:19:40 zenon kernel: scsi 0:0:3:0: SATA: enclosure_logical_id(0x5842b2b05020c600), slot(3) Mar 28 08:19:40 zenon kernel: scsi 0:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) Mar 28 08:19:40 zenon kernel: scsi 0:0:3:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1) Mar 28 08:19:40 zenon kernel: scsi 0:0:4:0: Direct-Access ATA WDC WD1002FAEX-0 1D05 PQ: 0 ANSI: 5 Mar 28 08:19:40 zenon kernel: scsi 0:0:4:0: SATA: handle(0x000d), sas_addr(0x4433221104000000), phy(4), device_name(0x4ee25001d9b104eb) Mar 28 08:19:40 zenon kernel: scsi 0:0:4:0: SATA: enclosure_logical_id(0x5842b2b05020c600), slot(7) Mar 28 08:19:40 zenon kernel: scsi 0:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) Mar 28 08:19:40 zenon kernel: scsi 0:0:4:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1) Mar 28 08:19:40 zenon kernel: scsi 0:0:5:0: Direct-Access ATA WDC WD1002FAEX-0 1D05 PQ: 0 ANSI: 5 Mar 28 08:19:40 zenon kernel: scsi 0:0:5:0: SATA: handle(0x000e), sas_addr(0x4433221107000000), phy(7), device_name(0x4ee25001c38204eb) Mar 28 08:19:40 zenon kernel: scsi 0:0:5:0: SATA: enclosure_logical_id(0x5842b2b05020c600), slot(4) Mar 28 08:19:40 zenon kernel: scsi 0:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) Mar 28 08:19:40 zenon kernel: scsi 0:0:5:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1) Mar 28 08:19:40 zenon kernel: scsi 0:0:6:0: Direct-Access ATA WDC WD1002FAEX-0 1D05 PQ: 0 ANSI: 5 Mar 28 08:19:40 zenon kernel: scsi 0:0:6:0: SATA: handle(0x000f), sas_addr(0x4433221106000000), phy(6), device_name(0x4ee250019a1baf96) Mar 28 08:19:40 zenon kernel: scsi 0:0:6:0: SATA: enclosure_logical_id(0x5842b2b05020c600), slot(5) Mar 28 08:19:40 zenon kernel: scsi 0:0:6:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) Mar 28 08:19:40 zenon kernel: scsi 0:0:6:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1) Mar 28 08:19:40 zenon kernel: scsi 0:0:7:0: Direct-Access ATA WDC WD1002FAEX-0 1D05 PQ: 0 ANSI: 5 Mar 28 08:19:40 zenon kernel: scsi 0:0:7:0: SATA: handle(0x0010), sas_addr(0x4433221105000000), phy(5), device_name(0x4ee2500136d4af96) Mar 28 08:19:40 zenon kernel: scsi 0:0:7:0: SATA: enclosure_logical_id(0x5842b2b05020c600), slot(6) Mar 28 08:19:40 zenon kernel: scsi 0:0:7:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) Mar 28 08:19:40 zenon kernel: scsi 0:0:7:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1) Mar 28 08:19:40 zenon kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Mar 28 08:19:40 zenon kernel: sd 0:0:1:0: Attached scsi generic sg1 type 0 Mar 28 08:19:40 zenon kernel: sd 0:0:2:0: Attached scsi generic sg2 type 0 Mar 28 08:19:40 zenon kernel: sd 0:0:3:0: Attached scsi generic sg3 type 0 Mar 28 08:19:40 zenon kernel: sd 0:0:4:0: Attached scsi generic sg4 type 0 Mar 28 08:19:40 zenon kernel: sd 0:0:5:0: Attached scsi generic sg5 type 0 Mar 28 08:19:40 zenon kernel: sd 0:0:6:0: Attached scsi generic sg6 type 0 Mar 28 08:19:40 zenon kernel: sd 0:0:7:0: Attached scsi generic sg7 type 0 Mar 28 08:19:40 zenon kernel: ata_piix 0000:00:1f.2: PCI INT C -> GSI 23 (level, low) -> IRQ 23 Mar 28 08:19:40 zenon kernel: ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ] Mar 28 08:19:40 zenon kernel: sd 0:0:6:0: [sdg] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Mar 28 08:19:40 zenon kernel: sd 0:0:5:0: [sdf] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Mar 28 08:19:40 zenon kernel: sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Mar 28 08:19:40 zenon kernel: sd 0:0:2:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Mar 28 08:19:40 zenon kernel: sd 0:0:1:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Mar 28 08:19:40 zenon kernel: sd 0:0:3:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Mar 28 08:19:40 zenon kernel: sd 0:0:4:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Mar 28 08:19:40 zenon kernel: sd 0:0:7:0: [sdh] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Mar 28 08:19:40 zenon kernel: sd 0:0:6:0: [sdg] Write Protect is off Mar 28 08:19:40 zenon kernel: sd 0:0:5:0: [sdf] Write Protect is off Mar 28 08:19:40 zenon kernel: sd 0:0:0:0: [sda] Write Protect is off Mar 28 08:19:40 zenon kernel: sd 0:0:2:0: [sdc] Write Protect is off Mar 28 08:19:40 zenon kernel: sd 0:0:6:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 28 08:19:40 zenon kernel: sd 0:0:5:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 28 08:19:40 zenon kernel: sd 0:0:4:0: [sde] Write Protect is off Mar 28 08:19:40 zenon kernel: sd 0:0:3:0: [sdd] Write Protect is off Mar 28 08:19:40 zenon kernel: sd 0:0:1:0: [sdb] Write Protect is off Mar 28 08:19:40 zenon kernel: sd 0:0:7:0: [sdh] Write Protect is off Mar 28 08:19:40 zenon kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 28 08:19:40 zenon kernel: sd 0:0:2:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 28 08:19:40 zenon kernel: sd 0:0:3:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 28 08:19:40 zenon kernel: sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 28 08:19:40 zenon kernel: sd 0:0:7:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 28 08:19:40 zenon kernel: sd 0:0:4:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 28 08:19:40 zenon kernel: sdg: sdg1 sdg2 sdg3 Mar 28 08:19:40 zenon kernel: sdf: sdf1 sdf2 sdf3 Mar 28 08:19:40 zenon kernel: sdc: sdc1 sdc2 sdc3 Mar 28 08:19:40 zenon kernel: sde: sde1 sde2 sde3 Mar 28 08:19:40 zenon kernel: sda: sda1 sda2 sda3 Mar 28 08:19:40 zenon kernel: sdb: sdb1 sdb2 sdb3 Mar 28 08:19:40 zenon kernel: sdd: sdd1 sdd2 sdd3 Mar 28 08:19:40 zenon kernel: sdh: sdh1 sdh2 sdh3 > Eric Moore > > > -----Original Message----- > > From: linux-scsi-owner@xxxxxxxxxxxxxxx [mailto:linux-scsi- > > owner@xxxxxxxxxxxxxxx] On Behalf Of Louis-David Mitterrand > > Sent: Wednesday, March 30, 2011 2:01 AM > > To: linux-scsi@xxxxxxxxxxxxxxx > > Subject: caviar black + mpt2sas horrific performance > > > > Hi, > > > > I am seeing horrific performance on a Dell T610 with a LSISAS2008 (Dell > > H200) card and 8 WD1002FAEX Caviar Black 1TB configured in mdadm raid6. > > > > The LSI card is upgraded to the latest 9.00 firmware: > > http://www.lsi.com/storage_home/products_home/host_bus_adapters/sas_hbas/in > > ternal/sas9211-8i/index.html > > and the 2.6.38.2 kernel uses the newer mpt2sas driver. > > > > On the T610 this command takes 20 minutes: > > > > tar -I pbzip2 -xvf linux-2.6.37.tar.bz2 22.64s user 3.34s system 2% > > cpu 20:00.69 total > > > > where on a lower spec'ed Poweredge 2900 III server (LSI Logic MegaRAID > > SAS 1078 + 8 x Hitachi Ultrastar 7K1000 in mdadm raid6) it takes 22 > > _seconds_: > > > > tar -I pbzip2 -xvf linux-2.6.37.tar.bz2 16.40s user 3.22s system 86% > > cpu 22.773 total > > > > Besides hardware, the other difference between servers is that the > > PE2900's MegaRAID has no JBOD mode so each disk must be configured as a > > "raid0" vdisk unit. On the T610 no configuration was necessary for the > > disks to "appear" in the OS. Would configuring them as raid0 vdisks > > change anything? > > > > Thanks in advance for any suggestion, > > -- > > To unsubscribe from this list: send the line "unsubscribe linux-scsi" in > > the body of a message to majordomo@xxxxxxxxxxxxxxx > > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
