On 11-02-15 10:46 AM, Douglas Gilbert wrote:
On 11-02-15 05:20 AM, Artem Bokhan wrote:
Hello!
I'm trying to get/set sctserc (SMART Command Transport Error Recovery Control)
data from sata disk attached to lsi megaraid controller with smartmontools, but
this function does not work.
I want to figure out: is this driver or firmware issue? May someone to help to
fix this?
The issue can be described as follows:
The ATA PASS-THROUGH(16) implementation in the SAT layer of the megaraid driver
or firmware does not return the ATA output registers if requested. This violates
SAT standard (http://www.t10.org/drafts.htm#SAT).
Expected: If CK_COND (bit 5 of CDB[2]) is set, ATA PASS-THROUGH(16) (CDB[0] =
0x85) shall return a CHECK CONDITION even if the ATA command completed
successfully, and return the ATA output registers in the sense data using ATA
return descriptor format (descriptor code 0x09).
Observed: If CK_COND is set and the ATA command completed successfully, ATA
PASS-THROUGH(16) does not return a CHECK CONDITION or the sense data does not
contain an ATA return descriptor.
See also the smartmontools SAT implementation
(http://sourceforge.net/apps/trac/smartmontools/browser/trunk/smartmontools/scsiata.cpp?rev=3258#L146)
for further info.
That code looked familiar but I'm not sure what your
point was referring to it. Anyway ...
Haven't worked much with Megaraid controllers but mptsas
controllers implement SAT (or at least did) in their
firmware. So upgrading the firmware on the controller fixed
the problems I had (some years back) with SAT compliance.
Just doing some tests comparing SAT compliance in libata
and a LSI SAS 9212-4i4e controller with the latest firmware.
I would expect a Megaraid controller with recent firmware to
behave in the same way as a the 9212 (mpt2sas driver).
The test is to send an ATA IDENTIFY DEVICE command through the
SCSI ATA PASS-THROUGH (16) command with the CK_COND bit set:
First libata:
# sg_sat_identify --ck_cond /dev/sg1 -vvv
open /dev/sg1 with flags=0x802
ATA pass through (16) cdb: 85 08 2e 00 00 00 01 00 00 00 00 00 00 00 ec 00
duration=1 ms
ATA pass through: Descriptor format, current; Sense key: No Sense
Additional sense: No additional sense information
Descriptor type: ATA Status Return
extend=0 error=0x0 sector_count=0x1
lba=0x000000
device=0x0 status=0x50
Raw sense data (in hex):
72 00 00 00 00 00 00 0e 09 0c 00 00 00 01 00 00
00 00 00 00 00 50 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Seem to have got ATA Result Descriptor but it was not indicated
#
So libata is broken in its SAT compliance in lk 2.6.37 .
And this is what should happen (SATA disk connected to a
SAS 9212-4i4e controller):
# sg_sat_identify --ck_cond /dev/sg4 -vvv
open /dev/sg4 with flags=0x802
ATA pass through (16) cdb: 85 08 2e 00 00 00 01 00 00 00 00 00 00 00 ec 00
duration=2 ms
ATA pass through: Descriptor format, current; Sense key: Recovered Error
Additional sense: ATA pass through information available
Descriptor type: ATA Status Return
extend=0 error=0x0 sector_count=0x0
lba=0x000000
device=0x0 status=0x50
Raw sense data (in hex):
72 01 00 1d 00 00 00 0e 09 0c 00 00 00 00 00 00
00 00 00 00 00 50 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Response for IDENTIFY DEVICE ATA command:
00 0c5a 3fff c837 0010 0000 0000 003f 0000 .Z ?. .7 .. .. .. .? ..
08 0000 0000 2020 2020 2020 2020 2020 2020 .. ..
.....
The sense key of Recovered Error is correct for no error
to report (as per SAT and SAT-2 standards) and of course
the response to the IDENTIFY DEVICE should be forwarded
(libata doesn't do that either).
Doug Gilbert
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
