From: Stephen M. Cameron <scameron@xxxxxxxxxxxxxxxxxx>
and use the doorbell reset method if available (which doesn't
lock up the controller if you properly save and restore all
the PCI registers that you're supposed to.)
Signed-off-by: Stephen M. Cameron <scameron@xxxxxxxxxxxxxxxxxx>
---
drivers/block/cciss.c | 72 ++++++++++---------------------------------------
1 files changed, 15 insertions(+), 57 deletions(-)
diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c
index 9fe6acf..7741e3b 100644
--- a/drivers/block/cciss.c
+++ b/drivers/block/cciss.c
@@ -4341,36 +4341,6 @@ static __devinit int cciss_message(struct pci_dev *pdev, unsigned char opcode, u
#define cciss_soft_reset_controller(p) cciss_message(p, 1, 0)
#define cciss_noop(p) cciss_message(p, 3, 0)
-static __devinit int cciss_reset_msi(struct pci_dev *pdev)
-{
-/* the #defines are stolen from drivers/pci/msi.h. */
-#define msi_control_reg(base) (base + PCI_MSI_FLAGS)
-#define PCI_MSIX_FLAGS_ENABLE (1 << 15)
-
- int pos;
- u16 control = 0;
-
- pos = pci_find_capability(pdev, PCI_CAP_ID_MSI);
- if (pos) {
- pci_read_config_word(pdev, msi_control_reg(pos), &control);
- if (control & PCI_MSI_FLAGS_ENABLE) {
- dev_info(&pdev->dev, "resetting MSI\n");
- pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSI_FLAGS_ENABLE);
- }
- }
-
- pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX);
- if (pos) {
- pci_read_config_word(pdev, msi_control_reg(pos), &control);
- if (control & PCI_MSIX_FLAGS_ENABLE) {
- dev_info(&pdev->dev, "resetting MSI-X\n");
- pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSIX_FLAGS_ENABLE);
- }
- }
-
- return 0;
-}
-
static int cciss_controller_hard_reset(struct pci_dev *pdev,
void * __iomem vaddr, bool use_doorbell)
{
@@ -4425,17 +4395,17 @@ static int cciss_controller_hard_reset(struct pci_dev *pdev,
* states or using the doorbell register. */
static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev)
{
- u16 saved_config_space[32];
u64 cfg_offset;
u32 cfg_base_addr;
u64 cfg_base_addr_index;
void __iomem *vaddr;
unsigned long paddr;
u32 misc_fw_support, active_transport;
- int rc, i;
+ int rc;
CfgTable_struct __iomem *cfgtable;
bool use_doorbell;
u32 board_id;
+ u16 command_register;
/* For controllers as old a the p600, this is very nearly
* the same thing as
@@ -4445,14 +4415,6 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev)
* pci_set_power_state(pci_dev, PCI_D0);
* pci_restore_state(pci_dev);
*
- * but we can't use these nice canned kernel routines on
- * kexec, because they also check the MSI/MSI-X state in PCI
- * configuration space and do the wrong thing when it is
- * set/cleared. Also, the pci_save/restore_state functions
- * violate the ordering requirements for restoring the
- * configuration space from the CCISS document (see the
- * comment below). So we roll our own ....
- *
* For controllers newer than the P600, the pci power state
* method of resetting doesn't work so we have another way
* using the doorbell register.
@@ -4471,8 +4433,13 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev)
return -ENODEV;
}
- for (i = 0; i < 32; i++)
- pci_read_config_word(pdev, 2*i, &saved_config_space[i]);
+ /* Save the PCI command register */
+ pci_read_config_word(pdev, 4, &command_register);
+ /* Turn the board off. This is so that later pci_restore_state()
+ * won't turn the board on before the rest of config space is ready.
+ */
+ pci_disable_device(pdev);
+ pci_save_state(pdev);
/* find the first memory BAR, so we can find the cfg table */
rc = cciss_pci_find_memory_BAR(pdev, &paddr);
@@ -4508,20 +4475,13 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev)
if (rc)
goto unmap_cfgtable;
- /* Restore the PCI configuration space. The Open CISS
- * Specification says, "Restore the PCI Configuration
- * Registers, offsets 00h through 60h. It is important to
- * restore the command register, 16-bits at offset 04h,
- * last. Do not restore the configuration status register,
- * 16-bits at offset 06h." Note that the offset is 2*i.
- */
- for (i = 0; i < 32; i++) {
- if (i == 2 || i == 3)
- continue;
- pci_write_config_word(pdev, 2*i, saved_config_space[i]);
+ pci_restore_state(pdev);
+ rc = pci_enable_device(pdev);
+ if (rc) {
+ dev_warn(&pdev->dev, "failed to enable device.\n");
+ goto unmap_cfgtable;
}
- wmb();
- pci_write_config_word(pdev, 4, saved_config_space[2]);
+ pci_write_config_word(pdev, 4, command_register);
/* Some devices (notably the HP Smart Array 5i Controller)
need a little pause here */
@@ -4581,8 +4541,6 @@ static __devinit int cciss_init_reset_devices(struct pci_dev *pdev)
return 0; /* just try to do the kdump anyhow. */
if (rc)
return -ENODEV;
- if (cciss_reset_msi(pdev))
- return -ENODEV;
/* Now try to get the controller to respond to a no-op */
for (i = 0; i < CCISS_POST_RESET_NOOP_RETRIES; i++) {
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
