On 8/9/2010 1:53 μμ, Konstantinos Skarlatos wrote:
On 4/9/2010 1:13 πμ, David Milburn wrote:
On Fri, Aug 06, 2010 at 08:21:16PM +0300, Konstantinos Skarlatos wrote:
> Hello,
> > Does this patch fix any of the mvs_abort_task:rc= 5 and the other
> problems that are being reported for this driver? for more info
please
> seehttp://marc.info/?l=linux-scsi&m=127583131805429&w=2
>
Hello,
Can you see if this patch prevents the ata_qc_issue warning?
Thanks,
David
drivers/scsi/libsas/sas_ata.c | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/drivers/scsi/libsas/sas_ata.c
b/drivers/scsi/libsas/sas_ata.c
index 042153c..ddbade7 100644
--- a/drivers/scsi/libsas/sas_ata.c
+++ b/drivers/scsi/libsas/sas_ata.c
@@ -347,6 +347,7 @@ static int sas_ata_scr_read(struct ata_link
*link, unsigned int sc_reg_in,
static struct ata_port_operations sas_sata_ops = {
.phy_reset = sas_ata_phy_reset,
.post_internal_cmd = sas_ata_post_internal,
+ .qc_defer = ata_std_qc_defer,
.qc_prep = ata_noop_qc_prep,
.qc_issue = sas_ata_qc_issue,
.qc_fill_rtf = sas_ata_qc_fill_rtf,
Hello,
I have been unable to patch my kernel, I am a noob at this and the
method i used a few months ago to apply Srinivas patches for mvsas
does not work now. I have asked for help from my distro (arch linux),
but if you have a quick and easy way for me to patch sas_ata.c and
reload the module without reboots or complete kernel recompilations I
would be grateful to hear it.
Kind regards
Hi, I finally managed to compile libsas. Here is dmesg output when
loading mvsas (BTW what do the messages about ata38.00 mean?). I will
report back when I do more testing
mvsas 0000:05:00.0: mvsas: driver version 0.8.2
mvsas 0000:05:00.0: PCI INT A -> Link[APC3] -> GSI 18 (level, low) -> IRQ 18
mvsas 0000:05:00.0: setting latency timer to 64
mvsas 0000:05:00.0: mvsas: PCI-E x4, Bandwidth Usage: 2.5 Gbps
scsi13 : mvsas
drivers/scsi/mvsas/mv_sas.c 1260:set wide port phy map 1
drivers/scsi/mvsas/mv_sas.c 1260:set wide port phy map 3
drivers/scsi/mvsas/mv_sas.c 1260:set wide port phy map 7
drivers/scsi/mvsas/mv_sas.c 1260:set wide port phy map f
ata38.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata38.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata38.00: qc timeout (cmd 0xec)
ata38.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata38.00: revalidation failed (errno=-5)
drivers/scsi/mvsas/mv_sas.c 1586:mvs_I_T_nexus_reset for device[1]:rc= 0
ata38.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata38: limiting SATA link speed to 1.5 Gbps
ata38.00: limiting speed to UDMA/133:PIO3
drivers/scsi/mvsas/mv_sas.c 1586:mvs_I_T_nexus_reset for device[1]:rc= 0
ata38.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata38.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata38.00: configured for UDMA/133
scsi 13:0:0:0: Direct-Access ATA ST31500541AS CC34 PQ: 0
ANSI: 5
sd 13:0:0:0: Attached scsi generic sg1 type 0
sd 13:0:0:0: [sdb] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:0:0: [sdb] Write Protect is off
sd 13:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdb:
ata39.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata39.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
sdb1
sd 13:0:0:0: [sdb] Attached SCSI disk
ata39.00: configured for UDMA/133
scsi 13:0:1:0: Direct-Access ATA ST31500541AS CC32 PQ: 0
ANSI: 5
sd 13:0:1:0: Attached scsi generic sg2 type 0
sd 13:0:1:0: [sdc] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:1:0: [sdc] Write Protect is off
sd 13:0:1:0: [sdc] Mode Sense: 00 3a 00 00
sd 13:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdc: sdc1
sd 13:0:1:0: [sdc] Attached SCSI disk
ata40.00: ATA-8: WDC WD15EADS-00S2B0, 01.00A01, max UDMA/133
ata40.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata40.00: configured for UDMA/133
scsi 13:0:2:0: Direct-Access ATA WDC WD15EADS-00S 01.0 PQ: 0
ANSI: 5
sd 13:0:2:0: Attached scsi generic sg3 type 0
sd 13:0:2:0: [sdd] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:2:0: [sdd] Write Protect is off
sd 13:0:2:0: [sdd] Mode Sense: 00 3a 00 00
sd 13:0:2:0: [sdd] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdd:
ata41.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata41.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata41.00: configured for UDMA/133
scsi 13:0:3:0: Direct-Access ATA ST31500541AS CC32 PQ: 0
ANSI: 5
sd 13:0:3:0: Attached scsi generic sg4 type 0
sd 13:0:3:0: [sde] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:3:0: [sde] Write Protect is off
sd 13:0:3:0: [sde] Mode Sense: 00 3a 00 00
sd 13:0:3:0: [sde] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sde: sde1
sd 13:0:3:0: [sde] Attached SCSI disk
ata42.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata42.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata42.00: configured for UDMA/133
scsi 13:0:4:0: Direct-Access ATA ST31500541AS CC34 PQ: 0
ANSI: 5
sd 13:0:4:0: [sdf] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:4:0: [sdf] Write Protect is off
sd 13:0:4:0: [sdf] Mode Sense: 00 3a 00 00
sd 13:0:4:0: [sdf] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 13:0:4:0: Attached scsi generic sg5 type 0
sdf:
ata43.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata43.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata43.00: configured for UDMA/133
scsi 13:0:5:0: Direct-Access ATA ST31500541AS CC34 PQ: 0
ANSI: 5
sd 13:0:5:0: Attached scsi generic sg6 type 0
sd 13:0:5:0: [sdg] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:5:0: [sdg] Write Protect is off
sd 13:0:5:0: [sdg] Mode Sense: 00 3a 00 00
sd 13:0:5:0: [sdg] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdg:
ata44.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata44.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata44.00: configured for UDMA/133
scsi 13:0:6:0: Direct-Access ATA ST31500541AS CC32 PQ: 0
ANSI: 5
sd 13:0:6:0: Attached scsi generic sg7 type 0
sd 13:0:6:0: [sdh] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:6:0: [sdh] Write Protect is off
sd 13:0:6:0: [sdh] Mode Sense: 00 3a 00 00
sd 13:0:6:0: [sdh] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdh: sdh1
sd 13:0:6:0: [sdh] Attached SCSI disk
ata45.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata45.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata45.00: configured for UDMA/133
scsi 13:0:7:0: Direct-Access ATA ST31500541AS CC34 PQ: 0
ANSI: 5
sd 13:0:7:0: Attached scsi generic sg8 type 0
sd 13:0:7:0: [sdi] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:7:0: [sdi] Write Protect is off
sd 13:0:7:0: [sdi] Mode Sense: 00 3a 00 00
sd 13:0:7:0: [sdi] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdi:
ata46.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata46.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata46.00: configured for UDMA/133
scsi 13:0:8:0: Direct-Access ATA ST31500541AS CC32 PQ: 0
ANSI: 5
sd 13:0:8:0: Attached scsi generic sg9 type 0
sd 13:0:8:0: [sdj] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:8:0: [sdj] Write Protect is off
sd 13:0:8:0: [sdj] Mode Sense: 00 3a 00 00
sd 13:0:8:0: [sdj] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdj: sdj1
sd 13:0:8:0: [sdj] Attached SCSI disk
ata47.00: qc timeout (cmd 0x27)
ata47.00: failed to read native max address (err_mask=0x4)
ata47.00: HPA support seems broken, skipping HPA handling
drivers/scsi/mvsas/mv_sas.c 1586:mvs_I_T_nexus_reset for device[a]:rc= 0
sdi1
sd 13:0:7:0: [sdi] Attached SCSI disk
ata47.00: ATA-8: ST31500341AS, CC1H, max UDMA/133
ata47.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata47.00: configured for UDMA/133
scsi 13:0:9:0: Direct-Access ATA ST31500341AS CC1H PQ: 0
ANSI: 5
sd 13:0:9:0: Attached scsi generic sg10 type 0
sd 13:0:9:0: [sdk] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:9:0: [sdk] Write Protect is off
sd 13:0:9:0: [sdk] Mode Sense: 00 3a 00 00
sd 13:0:9:0: [sdk] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdk: sdk1
sd 13:0:9:0: [sdk] Attached SCSI disk
sdf1
sd 13:0:4:0: [sdf] Attached SCSI disk
sdg1
sd 13:0:5:0: [sdg] Attached SCSI disk
sdd1
sd 13:0:2:0: [sdd] Attached SCSI disk
ata48.00: qc timeout (cmd 0x27)
ata48.00: failed to read native max address (err_mask=0x4)
ata48.00: HPA support seems broken, skipping HPA handling
drivers/scsi/mvsas/mv_sas.c 1586:mvs_I_T_nexus_reset for device[b]:rc= 0
ata48.00: ATA-8: ST31500341AS, CC1H, max UDMA/133
ata48.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata48.00: configured for UDMA/133
scsi 13:0:10:0: Direct-Access ATA ST31500341AS CC1H PQ: 0
ANSI: 5
sd 13:0:10:0: Attached scsi generic sg11 type 0
sd 13:0:10:0: [sdl] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:10:0: [sdl] Write Protect is off
sd 13:0:10:0: [sdl] Mode Sense: 00 3a 00 00
sd 13:0:10:0: [sdl] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdl:
ata49.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata49.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
sdl1
sd 13:0:10:0: [sdl] Attached SCSI disk
ata49.00: configured for UDMA/133
scsi 13:0:11:0: Direct-Access ATA ST31500541AS CC32 PQ: 0
ANSI: 5
sd 13:0:11:0: Attached scsi generic sg12 type 0
sd 13:0:11:0: [sdm] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:11:0: [sdm] Write Protect is off
sd 13:0:11:0: [sdm] Mode Sense: 00 3a 00 00
sd 13:0:11:0: [sdm] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdm: sdm1
sd 13:0:11:0: [sdm] Attached SCSI disk
ata50.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133
ata50.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata50.00: configured for UDMA/133
scsi 13:0:12:0: Direct-Access ATA WDC WD15EADS-00P 01.0 PQ: 0
ANSI: 5
sd 13:0:12:0: Attached scsi generic sg13 type 0
sd 13:0:12:0: [sdn] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:12:0: [sdn] Write Protect is off
sd 13:0:12:0: [sdn] Mode Sense: 00 3a 00 00
sd 13:0:12:0: [sdn] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdn:
scsi 13:0:13:0: Enclosure HP HP SAS EXP Card 1.00 PQ: 0
ANSI: 5
ses 13:0:13:0: Attached Enclosure device
ses 13:0:13:0: Attached scsi generic sg14 type 13
sdn1
sd 13:0:12:0: [sdn] Attached SCSI disk
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
