Tomas,
For the space, my e-mail shows tab. Can you setup your e-mail as "plain text" to see if resolve this problem?
for (wait = 0; wait < 30; wait++) {
> + msleep(1000);
> + }
>
It can be replaced by ssleep(30);
Also change:
> + printk(KERN_NOTICE "megaraid_sas: HBA recovery state machine,"
To:
> + printk(KERN_NOTICE "megaraid_sas: HBA recovery state machine, "
Thanks,
Bo Yang
-----Original Message-----
From: Tomas Henzl [mailto:thenzl@xxxxxxxxxx]
Sent: Friday, May 07, 2010 8:54 AM
To: Yang, Bo
Cc: 'James.Bottomley@xxxxxxxxxxxxxxxxxxxxx'; 'James.Bottomley@xxxxxxx'; 'linux-scsi@xxxxxxxxxxxxxxx'; 'akpm@xxxxxxxx'; 'linux-kernel@xxxxxxxxxxxxxxx'; Daftardar, Jayant
Subject: Re: [PATCH 3/7] scsi: megaraid_sas - Online COntroller Reset (OCR) PART-III
On 05/06/2010 05:52 PM, Yang, Bo wrote:
> This is third part of the Online Controller Reset. In ISR routine, if driver receive the FW state change interrupt
> And the online controller reset support enabled in FW, driver will read the controller register. Driver will issue
> Controller reset if the FW register state failure. Also driver will back up the pending cmds for the re-fire after
> the reset finished.
>
> Also Driver added the CTIO support to this patch.
>
> Signed-off-by Bo Yang<bo.yang@xxxxxxx>
>
> +static void
> +process_fw_state_change_wq(struct work_struct *work)
> +{
> + struct megasas_instance *instance =
> + container_of(work, struct megasas_instance, work_init);
> + u32 wait;
> + unsigned long flags;
> +
> + if (instance->adprecovery != MEGASAS_ADPRESET_SM_INFAULT) {
> + printk(KERN_NOTICE "megaraid_sas: error, recovery st %x \n",
> + instance->adprecovery);
> + return ;
> + }
> +
> + if (instance->adprecovery == MEGASAS_ADPRESET_SM_INFAULT) {
> + printk(KERN_NOTICE "megaraid_sas: FW detected to be in fault"
> + "state, restarting it...\n");
> +
> + instance->instancet->disable_intr(instance->reg_set);
> + atomic_set(&instance->fw_outstanding, 0);
> +
> + atomic_set(&instance->fw_reset_no_pci_access, 1);
> + instance->instancet->adp_reset(instance, instance->reg_set);
> + atomic_set(&instance->fw_reset_no_pci_access, 0 );
> +
> + printk(KERN_NOTICE "megaraid_sas: FW restarted successfully,"
> + "initiating next stage...\n");
> +
> + printk(KERN_NOTICE "megaraid_sas: HBA recovery state machine,"
> + "state 2 starting...\n");
> +
> + /*waitting for about 20 second before start the second init*/
> + for (wait = 0; wait < 30; wait++) {
> + msleep(1000);
> + }
>
Hi Bo,
I'm only curios - couldn't be the above loop replaced by ssleep(30);
and have the u32 wait; removed?
+ ssleep(30); /* wait for about 30 second before second init */
I guess you wanted to have a space after the comma in the printk, if yes I think
you should do this -> printk(KERN_NOTICE "megaraid_sas: HBA recovery state machine, "
It might be a problem with my mail reader, but it seems to me that you are using
spaces instead of tabs almost everywhere.
Tomas
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
