It doesn't make sense to update the link speed in the is_link_ok()
routine. Move it to it's own routine and acquire the device speed
when we're configuring the device initially as well as if there are
any netdev events received.
Signed-off-by: Robert Love <robert.w.love@xxxxxxxxx>
---
drivers/scsi/fcoe/fcoe.c | 42 +++++++++++++++++++++++++++++-------------
1 files changed, 29 insertions(+), 13 deletions(-)
diff --git a/drivers/scsi/fcoe/fcoe.c b/drivers/scsi/fcoe/fcoe.c
index 7022a16..4834d3c 100644
--- a/drivers/scsi/fcoe/fcoe.c
+++ b/drivers/scsi/fcoe/fcoe.c
@@ -74,6 +74,7 @@ static int fcoe_rcv(struct sk_buff *, struct net_device *,
static int fcoe_percpu_receive_thread(void *);
static void fcoe_clean_pending_queue(struct fc_lport *);
static void fcoe_percpu_clean(struct fc_lport *);
+static int fcoe_link_speed_update(struct fc_lport *);
static int fcoe_link_ok(struct fc_lport *);
static struct fc_lport *fcoe_hostlist_lookup(const struct net_device *);
@@ -631,6 +632,8 @@ static int fcoe_netdev_config(struct fc_lport *lport, struct net_device *netdev)
port->fcoe_pending_queue_active = 0;
setup_timer(&port->timer, fcoe_queue_timer, (unsigned long)lport);
+ fcoe_link_speed_update(lport);
+
if (!lport->vport) {
/*
* Use NAA 1&2 (FC-FS Rev. 2.0, Sec. 15) to generate WWNN/WWPN:
@@ -1829,6 +1832,9 @@ static int fcoe_device_notification(struct notifier_block *notifier,
FCOE_NETDEV_DBG(netdev, "Unknown event %ld "
"from netdev netlink\n", event);
}
+
+ fcoe_link_speed_update(lport);
+
if (link_possible && !fcoe_link_ok(lport))
fcoe_ctlr_link_up(&fcoe->ctlr);
else if (fcoe_ctlr_link_down(&fcoe->ctlr)) {
@@ -2128,26 +2134,19 @@ out_nomod:
}
/**
- * fcoe_link_ok() - Check if the link is OK for a local port
- * @lport: The local port to check link on
- *
- * Any permanently-disqualifying conditions have been previously checked.
- * This also updates the speed setting, which may change with link for 100/1000.
- *
- * This function should probably be checking for PAUSE support at some point
- * in the future. Currently Per-priority-pause is not determinable using
- * ethtool, so we shouldn't be restrictive until that problem is resolved.
- *
- * Returns: 0 if link is OK for use by FCoE.
+ * fcoe_link_speed_update() - Update the supported and actual link speeds
+ * @lport: The local port to update speeds for
*
+ * Returns: 0 if the ethtool query was successful
+ * -1 if the ethtool query failed
*/
-int fcoe_link_ok(struct fc_lport *lport)
+int fcoe_link_speed_update(struct fc_lport *lport)
{
struct fcoe_port *port = lport_priv(lport);
struct net_device *netdev = port->fcoe->netdev;
struct ethtool_cmd ecmd = { ETHTOOL_GSET };
- if (netif_oper_up(netdev) && !dev_ethtool_get_settings(netdev, &ecmd)) {
+ if (!dev_ethtool_get_settings(netdev, &ecmd)) {
lport->link_supported_speeds &=
~(FC_PORTSPEED_1GBIT | FC_PORTSPEED_10GBIT);
if (ecmd.supported & (SUPPORTED_1000baseT_Half |
@@ -2167,6 +2166,23 @@ int fcoe_link_ok(struct fc_lport *lport)
}
/**
+ * fcoe_link_ok() - Check if the link is OK for a local port
+ * @lport: The local port to check link on
+ *
+ * Returns: 0 if link is UP and OK, -1 if not
+ *
+ */
+int fcoe_link_ok(struct fc_lport *lport)
+{
+ struct fcoe_port *port = lport_priv(lport);
+ struct net_device *netdev = port->fcoe->netdev;
+
+ if (netif_oper_up(netdev))
+ return 0;
+ return -1;
+}
+
+/**
* fcoe_percpu_clean() - Clear all pending skbs for an local port
* @lport: The local port whose skbs are to be cleared
*
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
