Hi,
I have a LSI 3801E PCIe SAS HBA based on the LSI 1068E controller connected to 8 SATA hot swap drive bays running under Fedora 11 X86_64 (2.6.29.4-167.fc11). I have 4 SATA drives hanging off of each external (4 SAS channels) connector. I am having the following issue. If I have 2+ drives on the same connect and replace one drive, when the new drive is detected, it resets all drives on the connector. So any drive that was mounted goes offline.
For example:
/dev/sde1 - mounted to /media/disk1
/dev/sdf, /dev/sdg, /dev/sdh - 3 other drives connected to the same SAS connector.
I removed sdh and reinserted it. When the drive is discovered and given a device entry, /dev/sde gets some sort of reset that makes the /media/disk1 mount fail and is no longer available. I've posted a copy of the kernel messages when this happened.
Is this a driver issue, a configuration issue, or is it just how the 1068E works and there is no way around it?
Thanks!
- Mike
Michael Moore
Staff Engineer - Network
SOLiD Advanced Research and Collaborations 500 Cummings Center Suite 2400 Beverly, MA 01915
T: 508-383-7486
Michael.Moore@xxxxxxxxxxxx
Mike.Moore@xxxxxxxxxxxxxxxxxxxxx
Dec 3 12:23:13 bev-archive kernel: mptsas: ioc0: attaching sata device, channel 0, id 19, phy 0
Dec 3 12:23:13 bev-archive kernel: scsi 8:0:0:0: Direct-Access ATA WDC WD15EADS-00P 0A01 PQ: 0 ANSI: 5
Dec 3 12:23:13 bev-archive kernel: sd 8:0:0:0: [sde] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:23:13 bev-archive kernel: sd 8:0:0:0: [sde] Write Protect is off
Dec 3 12:23:13 bev-archive kernel: sd 8:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:23:13 bev-archive kernel: sd 8:0:0:0: [sde] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:23:13 bev-archive kernel: sd 8:0:0:0: [sde] Write Protect is off
Dec 3 12:23:13 bev-archive kernel: sd 8:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:23:13 bev-archive kernel: sde: sde1
Dec 3 12:23:13 bev-archive kernel: sd 8:0:0:0: [sde] Attached SCSI disk
Dec 3 12:23:13 bev-archive kernel: sd 8:0:0:0: Attached scsi generic sg5 type 0
Dec 3 12:23:13 bev-archive ata_id[2481]: HDIO_GET_IDENTITY failed for '/dev/.tmp-block-8:64'
Dec 3 12:23:56 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:24:00 bev-archive kernel: mptsas: ioc0: removing sata device, channel 0, id 19, phy 0
Dec 3 12:24:00 bev-archive kernel: sd 8:0:0:0: [sde] Synchronizing SCSI cache
Dec 3 12:24:00 bev-archive kernel: sd 8:0:0:0: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
Dec 3 12:24:26 bev-archive kernel: mptsas: ioc0: attaching sata device, channel 0, id 19, phy 0
Dec 3 12:24:26 bev-archive kernel: scsi 8:0:1:0: Direct-Access ATA WDC WD15EADS-00P 0A01 PQ: 0 ANSI: 5
Dec 3 12:24:26 bev-archive kernel: sd 8:0:1:0: [sde] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:26 bev-archive kernel: sd 8:0:1:0: [sde] Write Protect is off
Dec 3 12:24:26 bev-archive kernel: sd 8:0:1:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:26 bev-archive kernel: sd 8:0:1:0: [sde] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:26 bev-archive kernel: sd 8:0:1:0: [sde] Write Protect is off
Dec 3 12:24:26 bev-archive kernel: sd 8:0:1:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:26 bev-archive kernel: sde: sde1
Dec 3 12:24:26 bev-archive kernel: sd 8:0:1:0: [sde] Attached SCSI disk
Dec 3 12:24:26 bev-archive kernel: sd 8:0:1:0: Attached scsi generic sg5 type 0
Dec 3 12:24:26 bev-archive ata_id[2533]: HDIO_GET_IDENTITY failed for '/dev/.tmp-block-8:64'
Dec 3 12:24:39 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:24:44 bev-archive kernel: mptsas: ioc0: removing sata device, channel 0, id 19, phy 0
Dec 3 12:24:44 bev-archive kernel: sd 8:0:1:0: [sde] Synchronizing SCSI cache
Dec 3 12:24:44 bev-archive kernel: sd 8:0:1:0: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
Dec 3 12:24:50 bev-archive kernel: mptsas: ioc0: attaching sata device, channel 0, id 19, phy 0
Dec 3 12:24:50 bev-archive kernel: scsi 8:0:2:0: Direct-Access ATA WDC WD15EADS-00P 0A01 PQ: 0 ANSI: 5
Dec 3 12:24:50 bev-archive kernel: sd 8:0:2:0: [sde] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:50 bev-archive kernel: sd 8:0:2:0: [sde] Write Protect is off
Dec 3 12:24:50 bev-archive kernel: sd 8:0:2:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:50 bev-archive kernel: sd 8:0:2:0: [sde] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:50 bev-archive kernel: sd 8:0:2:0: [sde] Write Protect is off
Dec 3 12:24:50 bev-archive kernel: sd 8:0:2:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:50 bev-archive kernel: sde: sde1
Dec 3 12:24:50 bev-archive kernel: sd 8:0:2:0: [sde] Attached SCSI disk
Dec 3 12:24:50 bev-archive kernel: sd 8:0:2:0: Attached scsi generic sg5 type 0
Dec 3 12:24:50 bev-archive ata_id[2580]: HDIO_GET_IDENTITY failed for '/dev/.tmp-block-8:64'
Dec 3 12:24:52 bev-archive kernel: mptsas: ioc0: attaching sata device, channel 0, id 24, phy 1
Dec 3 12:24:52 bev-archive kernel: scsi 8:0:3:0: Direct-Access ATA WDC WD15EADS-00P 0A01 PQ: 0 ANSI: 5
Dec 3 12:24:52 bev-archive kernel: sd 8:0:3:0: [sdf] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:52 bev-archive kernel: sd 8:0:3:0: [sdf] Write Protect is off
Dec 3 12:24:52 bev-archive kernel: sd 8:0:3:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:52 bev-archive kernel: sd 8:0:3:0: [sdf] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:52 bev-archive kernel: sd 8:0:3:0: [sdf] Write Protect is off
Dec 3 12:24:52 bev-archive kernel: sd 8:0:3:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:52 bev-archive kernel: sdf: sdf1
Dec 3 12:24:52 bev-archive kernel: sd 8:0:3:0: [sdf] Attached SCSI disk
Dec 3 12:24:52 bev-archive kernel: sd 8:0:3:0: Attached scsi generic sg6 type 0
Dec 3 12:24:52 bev-archive ata_id[2609]: HDIO_GET_IDENTITY failed for '/dev/.tmp-block-8:80'
Dec 3 12:24:54 bev-archive kernel: mptsas: ioc0: attaching sata device, channel 0, id 18, phy 2
Dec 3 12:24:54 bev-archive kernel: scsi 8:0:4:0: Direct-Access ATA WDC WD15EADS-00P 0A01 PQ: 0 ANSI: 5
Dec 3 12:24:54 bev-archive kernel: sd 8:0:4:0: [sdg] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:54 bev-archive kernel: sd 8:0:4:0: [sdg] Write Protect is off
Dec 3 12:24:54 bev-archive kernel: sd 8:0:4:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:54 bev-archive kernel: sd 8:0:4:0: [sdg] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:54 bev-archive kernel: sd 8:0:4:0: [sdg] Write Protect is off
Dec 3 12:24:54 bev-archive kernel: sd 8:0:4:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:54 bev-archive kernel: sdg: sdg1
Dec 3 12:24:54 bev-archive kernel: sd 8:0:4:0: [sdg] Attached SCSI disk
Dec 3 12:24:54 bev-archive kernel: sd 8:0:4:0: Attached scsi generic sg7 type 0
Dec 3 12:24:54 bev-archive ata_id[2640]: HDIO_GET_IDENTITY failed for '/dev/.tmp-block-8:96'
Dec 3 12:24:55 bev-archive kernel: mptsas: ioc0: attaching sata device, channel 0, id 25, phy 3
Dec 3 12:24:55 bev-archive kernel: scsi 8:0:5:0: Direct-Access ATA WDC WD15EADS-00P 0A01 PQ: 0 ANSI: 5
Dec 3 12:24:55 bev-archive kernel: sd 8:0:5:0: [sdh] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:55 bev-archive kernel: sd 8:0:5:0: [sdh] Write Protect is off
Dec 3 12:24:55 bev-archive kernel: sd 8:0:5:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:55 bev-archive kernel: sd 8:0:5:0: [sdh] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:24:55 bev-archive kernel: sd 8:0:5:0: [sdh] Write Protect is off
Dec 3 12:24:55 bev-archive kernel: sd 8:0:5:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:24:55 bev-archive kernel: sdh: unknown partition table
Dec 3 12:24:55 bev-archive kernel: sd 8:0:5:0: [sdh] Attached SCSI disk
Dec 3 12:24:55 bev-archive kernel: sd 8:0:5:0: Attached scsi generic sg8 type 0
Dec 3 12:24:55 bev-archive ata_id[2669]: HDIO_GET_IDENTITY failed for '/dev/.tmp-block-8:112'
Dec 3 12:26:27 bev-archive ntpd[2093]: synchronized to 172.18.241.21, stratum 3
Dec 3 12:26:27 bev-archive ntpd[2093]: time reset +0.480600 s
Dec 3 12:26:57 bev-archive kernel: kjournald starting. Commit interval 5 seconds
Dec 3 12:26:57 bev-archive kernel: EXT3 FS on sde1, internal journal
Dec 3 12:26:57 bev-archive kernel: EXT3-fs: mounted filesystem with ordered data mode.
Dec 3 12:27:08 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:27:13 bev-archive kernel: mptsas: ioc0: removing sata device, channel 0, id 25, phy 3
Dec 3 12:27:13 bev-archive kernel: sd 8:0:5:0: [sdh] Synchronizing SCSI cache
Dec 3 12:27:13 bev-archive kernel: sd 8:0:5:0: [sdh] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
Dec 3 12:27:40 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:27:40 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:27:40 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:27:44 bev-archive kernel: mptsas: ioc0: removing sata device, channel 0, id 18, phy 2
Dec 3 12:27:44 bev-archive kernel: sd 8:0:4:0: [sdg] Synchronizing SCSI cache
Dec 3 12:27:44 bev-archive kernel: sd 8:0:4:0: [sdg] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
Dec 3 12:27:44 bev-archive kernel: mptsas: ioc0: removing sata device, channel 0, id 19, phy 0
Dec 3 12:27:44 bev-archive kernel: Aborting journal on device sde1.
Dec 3 12:27:44 bev-archive kernel: ------------[ cut here ]------------
Dec 3 12:27:44 bev-archive kernel: WARNING: at fs/buffer.c:1247 mark_buffer_dirty+0x34/0x7e() (Not tainted)
Dec 3 12:27:44 bev-archive kernel: Hardware name: PowerEdge SC1430
Dec 3 12:27:44 bev-archive kernel: Modules linked in: bridge stp llc bnep sco l2cap bluetooth autofs4 sunrpc ip6t_REJECT nf_conntrack_ipv6 ip6table_filter ip6_tables ipv6 p4_clockmod speedstep_lib freq_table dm_multipath raid0 uinput mptsas i5k_amb hwmon i5000_edac e1000 mptscsih edac_core mptbase serio_raw scsi_transport_sas iTCO_wdt iTCO_vendor_support sata_sil24 shpchp dcdbas tg3 ppdev parport_pc parport pcspkr ata_generic pata_acpi radeon drm i2c_algo_bit i2c_core [last unloaded: freq_table]
Dec 3 12:27:44 bev-archive kernel: Pid: 2720, comm: kjournald Not tainted 2.6.29.4-167.fc11.x86_64 #1
Dec 3 12:27:44 bev-archive kernel: Call Trace:
Dec 3 12:27:44 bev-archive kernel: [<ffffffff810489bf>] warn_slowpath+0xbc/0xf0
Dec 3 12:27:44 bev-archive kernel: [<ffffffff8102a103>] ? default_spin_lock_flags+0x9/0xe
Dec 3 12:27:44 bev-archive kernel: [<ffffffff813abc1c>] ? _spin_unlock_irqrestore+0x2c/0x42
Dec 3 12:27:44 bev-archive kernel: [<ffffffff813abc1c>] ? _spin_unlock_irqrestore+0x2c/0x42
Dec 3 12:27:44 bev-archive kernel: [<ffffffff81048f94>] ? release_console_sem+0x1c1/0x1f6
Dec 3 12:27:44 bev-archive kernel: [<ffffffff810f3e1c>] mark_buffer_dirty+0x34/0x7e
Dec 3 12:27:44 bev-archive kernel: [<ffffffff81161ebd>] journal_update_superblock+0x7f/0xd4
Dec 3 12:27:44 bev-archive kernel: [<ffffffff8116206d>] __journal_abort_soft+0xa7/0xb0
Dec 3 12:27:44 bev-archive kernel: [<ffffffff811619ab>] ? __journal_remove_journal_head+0xef/0xf4
Dec 3 12:27:44 bev-archive kernel: [<ffffffff81162084>] journal_abort+0xe/0x10
Dec 3 12:27:44 bev-archive kernel: [<ffffffff8115f85d>] journal_commit_transaction+0x9e3/0xdf2
Dec 3 12:27:44 bev-archive kernel: [<ffffffff810526a1>] ? try_to_del_timer_sync+0x5a/0x66
Dec 3 12:27:44 bev-archive kernel: [<ffffffff811628e1>] kjournald+0xee/0x23f
Dec 3 12:27:44 bev-archive kernel: [<ffffffff8105ca4b>] ? autoremove_wake_function+0x0/0x39
Dec 3 12:27:44 bev-archive kernel: [<ffffffff811627f3>] ? kjournald+0x0/0x23f
Dec 3 12:27:44 bev-archive kernel: [<ffffffff8105c6b5>] kthread+0x4d/0x78
Dec 3 12:27:44 bev-archive kernel: [<ffffffff8101264a>] child_rip+0xa/0x20
Dec 3 12:27:44 bev-archive kernel: [<ffffffff81011f67>] ? restore_args+0x0/0x30
Dec 3 12:27:44 bev-archive kernel: [<ffffffff8105c668>] ? kthread+0x0/0x78
Dec 3 12:27:44 bev-archive kernel: [<ffffffff81012640>] ? child_rip+0x0/0x20
Dec 3 12:27:44 bev-archive kernel: ---[ end trace 3aed6b53160d755f ]---
Dec 3 12:27:44 bev-archive kernel: journal commit I/O error
Dec 3 12:27:44 bev-archive kernel: sd 8:0:2:0: [sde] Synchronizing SCSI cache
Dec 3 12:27:44 bev-archive kernel: sd 8:0:2:0: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
Dec 3 12:27:44 bev-archive kernel: mptsas: ioc0: removing sata device, channel 0, id 24, phy 1
Dec 3 12:27:44 bev-archive kernel: sd 8:0:3:0: [sdf] Synchronizing SCSI cache
Dec 3 12:27:44 bev-archive kernel: sd 8:0:3:0: [sdf] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
Dec 3 12:27:46 bev-archive kernel: mptsas: ioc0: attaching sata device, channel 0, id 19, phy 0
Dec 3 12:27:46 bev-archive kernel: scsi 8:0:6:0: Direct-Access ATA WDC WD15EADS-00P 0A01 PQ: 0 ANSI: 5
Dec 3 12:27:46 bev-archive kernel: sd 8:0:6:0: [sdf] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:27:46 bev-archive kernel: sd 8:0:6:0: [sdf] Write Protect is off
Dec 3 12:27:46 bev-archive kernel: sd 8:0:6:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:27:46 bev-archive kernel: sd 8:0:6:0: [sdf] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:27:46 bev-archive kernel: sd 8:0:6:0: [sdf] Write Protect is off
Dec 3 12:27:46 bev-archive kernel: sd 8:0:6:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:27:46 bev-archive kernel: sdf: sdf1
Dec 3 12:27:46 bev-archive kernel: sd 8:0:6:0: [sdf] Attached SCSI disk
Dec 3 12:27:46 bev-archive kernel: sd 8:0:6:0: Attached scsi generic sg5 type 0
Dec 3 12:27:46 bev-archive ata_id[2806]: HDIO_GET_IDENTITY failed for '/dev/.tmp-block-8:80'
Dec 3 12:27:52 bev-archive kernel: mptsas: ioc0: attaching sata device, channel 0, id 25, phy 3
Dec 3 12:27:52 bev-archive kernel: scsi 8:0:7:0: Direct-Access ATA WDC WD15EADS-00P 0A01 PQ: 0 ANSI: 5
Dec 3 12:27:52 bev-archive kernel: sd 8:0:7:0: [sdg] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:27:52 bev-archive kernel: sd 8:0:7:0: [sdg] Write Protect is off
Dec 3 12:27:52 bev-archive kernel: sd 8:0:7:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:27:52 bev-archive kernel: sd 8:0:7:0: [sdg] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:27:52 bev-archive kernel: sd 8:0:7:0: [sdg] Write Protect is off
Dec 3 12:27:52 bev-archive kernel: sd 8:0:7:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:27:52 bev-archive kernel: sdg: unknown partition table
Dec 3 12:27:52 bev-archive kernel: sd 8:0:7:0: [sdg] Attached SCSI disk
Dec 3 12:27:52 bev-archive kernel: sd 8:0:7:0: Attached scsi generic sg6 type 0
Dec 3 12:27:52 bev-archive ata_id[2839]: HDIO_GET_IDENTITY failed for '/dev/.tmp-block-8:96'
Dec 3 12:28:09 bev-archive kernel: ext3_abort called.
Dec 3 12:28:09 bev-archive kernel: EXT3-fs error (device sde1): ext3_put_super: Couldn't clean up the journal
Dec 3 12:28:09 bev-archive kernel: Remounting filesystem read-only
Dec 3 12:28:44 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:28:49 bev-archive kernel: mptsas: ioc0: removing sata device, channel 0, id 19, phy 0
Dec 3 12:28:49 bev-archive kernel: sd 8:0:6:0: [sdf] Synchronizing SCSI cache
Dec 3 12:28:49 bev-archive kernel: sd 8:0:6:0: [sdf] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
Dec 3 12:28:59 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:28:59 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:28:59 bev-archive kernel: mptbase: ioc0: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00)
Dec 3 12:29:03 bev-archive kernel: mptsas: ioc0: removing sata device, channel 0, id 25, phy 3
Dec 3 12:29:03 bev-archive kernel: sd 8:0:7:0: [sdg] Synchronizing SCSI cache
Dec 3 12:29:03 bev-archive kernel: sd 8:0:7:0: [sdg] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
Dec 3 12:29:11 bev-archive kernel: mptsas: ioc0: attaching sata device, channel 0, id 19, phy 0
Dec 3 12:29:11 bev-archive kernel: scsi 8:0:8:0: Direct-Access ATA WDC WD15EADS-00P 0A01 PQ: 0 ANSI: 5
Dec 3 12:29:11 bev-archive kernel: sd 8:0:8:0: [sde] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:29:11 bev-archive kernel: sd 8:0:8:0: [sde] Write Protect is off
Dec 3 12:29:11 bev-archive kernel: sd 8:0:8:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:29:11 bev-archive kernel: sd 8:0:8:0: [sde] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
Dec 3 12:29:11 bev-archive kernel: sd 8:0:8:0: [sde] Write Protect is off
Dec 3 12:29:11 bev-archive kernel: sd 8:0:8:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec 3 12:29:11 bev-archive kernel: sde: sde1
Dec 3 12:29:11 bev-archive kernel: sd 8:0:8:0: [sde] Attached SCSI disk
Dec 3 12:29:11 bev-archive kernel: sd 8:0:8:0: Attached scsi generic sg5 type 0
Dec 3 12:29:11 bev-archive ata_id[2909]: HDIO_GET_IDENTITY failed for '/dev/.tmp-block-8:64'
Dec 3 12:29:27 bev-archive kernel: kjournald starting. Commit interval 5 seconds
Dec 3 12:29:27 bev-archive kernel: EXT3 FS on sde1, internal journal
Dec 3 12:29:27 bev-archive kernel: EXT3-fs: recovery complete.
Dec 3 12:29:27 bev-archive kernel: EXT3-fs: mounted filesystem with ordered data mode.
