Addition of SLI4 Interface - Base Support - Part 3 of 6
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@xxxxxxxxxx>
---
lpfc_scsi.h | 2
lpfc_sli.c | 1263 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++--
lpfc_sli.h | 27 +
lpfc_sli4.h | 467 +++++++++++++++++++++
lpfc_vport.c | 23 +
5 files changed, 1748 insertions(+), 34 deletions(-)
diff -upNr a/drivers/scsi/lpfc/lpfc_scsi.h b/drivers/scsi/lpfc/lpfc_scsi.h
--- a/drivers/scsi/lpfc/lpfc_scsi.h 2008-12-16 09:34:12.000000000 -0500
+++ b/drivers/scsi/lpfc/lpfc_scsi.h 2009-05-22 13:16:40.000000000 -0400
@@ -140,6 +140,8 @@ struct lpfc_scsi_buf {
struct fcp_rsp *fcp_rsp;
struct ulp_bde64 *fcp_bpl;
+ dma_addr_t dma_phys_bpl;
+
/* cur_iocbq has phys of the dma-able buffer.
* Iotag is in here
*/
diff -upNr a/drivers/scsi/lpfc/lpfc_sli4.h b/drivers/scsi/lpfc/lpfc_sli4.h
--- a/drivers/scsi/lpfc/lpfc_sli4.h 1969-12-31 19:00:00.000000000 -0500
+++ b/drivers/scsi/lpfc/lpfc_sli4.h 2009-05-22 13:16:40.000000000 -0400
@@ -0,0 +1,467 @@
+/*******************************************************************
+ * This file is part of the Emulex Linux Device Driver for *
+ * Fibre Channel Host Bus Adapters. *
+ * Copyright (C) 2009 Emulex. All rights reserved. *
+ * EMULEX and SLI are trademarks of Emulex. *
+ * www.emulex.com *
+ * *
+ * This program is free software; you can redistribute it and/or *
+ * modify it under the terms of version 2 of the GNU General *
+ * Public License as published by the Free Software Foundation. *
+ * This program is distributed in the hope that it will be useful. *
+ * ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND *
+ * WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, *
+ * FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT, ARE *
+ * DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD *
+ * TO BE LEGALLY INVALID. See the GNU General Public License for *
+ * more details, a copy of which can be found in the file COPYING *
+ * included with this package. *
+ *******************************************************************/
+
+#define LPFC_ACTIVE_MBOX_WAIT_CNT 100
+#define LPFC_RELEASE_NOTIFICATION_INTERVAL 32
+#define LPFC_GET_QE_REL_INT 32
+#define LPFC_RPI_LOW_WATER_MARK 10
+/* Number of SGL entries can be posted in a 4KB nonembedded mbox command */
+#define LPFC_NEMBED_MBOX_SGL_CNT 254
+
+/* Multi-queue arrangement for fast-path FCP work queues */
+#define LPFC_FN_EQN_MAX 8
+#define LPFC_SP_EQN_DEF 1
+#define LPFC_FP_EQN_DEF 1
+#define LPFC_FP_EQN_MIN 1
+#define LPFC_FP_EQN_MAX (LPFC_FN_EQN_MAX - LPFC_SP_EQN_DEF)
+
+#define LPFC_FN_WQN_MAX 32
+#define LPFC_SP_WQN_DEF 1
+#define LPFC_FP_WQN_DEF 4
+#define LPFC_FP_WQN_MIN 1
+#define LPFC_FP_WQN_MAX (LPFC_FN_WQN_MAX - LPFC_SP_WQN_DEF)
+
+/*
+ * Provide the default FCF Record attributes used by the driver
+ * when nonFIP mode is configured and there is no other default
+ * FCF Record attributes.
+ */
+#define LPFC_FCOE_FCF_DEF_INDEX 0
+#define LPFC_FCOE_FCF_GET_FIRST 0xFFFF
+#define LPFC_FCOE_FCF_NEXT_NONE 0xFFFF
+
+/* First 3 bytes of default FCF MAC is specified by FC_MAP */
+#define LPFC_FCOE_FCF_MAC3 0xFF
+#define LPFC_FCOE_FCF_MAC4 0xFF
+#define LPFC_FCOE_FCF_MAC5 0xFE
+#define LPFC_FCOE_FCF_MAP0 0x0E
+#define LPFC_FCOE_FCF_MAP1 0xFC
+#define LPFC_FCOE_FCF_MAP2 0x00
+#define LPFC_FCOE_MAX_RCV_SIZE 0x5AC
+#define LPFC_FCOE_FKA_ADV_PER 0
+#define LPFC_FCOE_FIP_PRIORITY 0x80
+
+enum lpfc_sli4_queue_type {
+ LPFC_EQ,
+ LPFC_GCQ,
+ LPFC_MCQ,
+ LPFC_WCQ,
+ LPFC_RCQ,
+ LPFC_MQ,
+ LPFC_WQ,
+ LPFC_HRQ,
+ LPFC_DRQ
+};
+
+/* The queue sub-type defines the functional purpose of the queue */
+enum lpfc_sli4_queue_subtype {
+ LPFC_NONE,
+ LPFC_MBOX,
+ LPFC_FCP,
+ LPFC_ELS,
+ LPFC_USOL
+};
+
+union sli4_qe {
+ void *address;
+ struct lpfc_eqe *eqe;
+ struct lpfc_cqe *cqe;
+ struct lpfc_mcqe *mcqe;
+ struct lpfc_wcqe_complete *wcqe_complete;
+ struct lpfc_wcqe_release *wcqe_release;
+ struct sli4_wcqe_xri_aborted *wcqe_xri_aborted;
+ struct lpfc_rcqe_complete *rcqe_complete;
+ struct lpfc_mqe *mqe;
+ union lpfc_wqe *wqe;
+ struct lpfc_rqe *rqe;
+};
+
+struct lpfc_queue {
+ struct list_head list;
+ enum lpfc_sli4_queue_type type;
+ enum lpfc_sli4_queue_subtype subtype;
+ struct lpfc_hba *phba;
+ struct list_head child_list;
+ uint32_t entry_count; /* Number of entries to support on the queue */
+ uint32_t entry_size; /* Size of each queue entry. */
+ uint32_t queue_id; /* Queue ID assigned by the hardware */
+ struct list_head page_list;
+ uint32_t page_count; /* Number of pages allocated for this queue */
+
+ uint32_t host_index; /* The host's index for putting or getting */
+ uint32_t hba_index; /* The last known hba index for get or put */
+ union sli4_qe qe[1]; /* array to index entries (must be last) */
+};
+
+struct lpfc_cq_event {
+ struct list_head list;
+ union {
+ struct lpfc_mcqe mcqe_cmpl;
+ struct lpfc_acqe_link acqe_link;
+ struct lpfc_acqe_fcoe acqe_fcoe;
+ struct lpfc_acqe_dcbx acqe_dcbx;
+ struct lpfc_rcqe rcqe_cmpl;
+ struct sli4_wcqe_xri_aborted wcqe_axri;
+ } cqe;
+};
+
+struct lpfc_sli4_link {
+ uint8_t speed;
+ uint8_t duplex;
+ uint8_t status;
+ uint8_t physical;
+ uint8_t fault;
+};
+
+struct lpfc_fcf {
+ uint8_t fabric_name[8];
+ uint8_t mac_addr[6];
+ uint16_t fcf_indx;
+ uint16_t fcfi;
+ uint32_t fcf_flag;
+#define FCF_AVAILABLE 0x01 /* FCF available for discovery */
+#define FCF_REGISTERED 0x02 /* FCF registered with FW */
+#define FCF_DISCOVERED 0x04 /* FCF discovery started */
+#define FCF_BOOT_ENABLE 0x08 /* Boot bios use this FCF */
+#define FCF_IN_USE 0x10 /* Atleast one discovery completed */
+#define FCF_VALID_VLAN 0x20 /* Use the vlan id specified */
+ uint32_t priority;
+ uint32_t addr_mode;
+ uint16_t vlan_id;
+};
+
+#define LPFC_REGION23_SIGNATURE "RG23"
+#define LPFC_REGION23_VERSION 1
+#define LPFC_REGION23_LAST_REC 0xff
+struct lpfc_fip_param_hdr {
+ uint8_t type;
+#define FCOE_PARAM_TYPE 0xA0
+ uint8_t length;
+#define FCOE_PARAM_LENGTH 2
+ uint8_t parm_version;
+#define FIPP_VERSION 0x01
+ uint8_t parm_flags;
+#define lpfc_fip_param_hdr_fipp_mode_SHIFT 6
+#define lpfc_fip_param_hdr_fipp_mode_MASK 0x3
+#define lpfc_fip_param_hdr_fipp_mode_WORD parm_flags
+#define FIPP_MODE_ON 0x2
+#define FIPP_MODE_OFF 0x0
+#define FIPP_VLAN_VALID 0x1
+};
+
+struct lpfc_fcoe_params {
+ uint8_t fc_map[3];
+ uint8_t reserved1;
+ uint16_t vlan_tag;
+ uint8_t reserved[2];
+};
+
+struct lpfc_fcf_conn_hdr {
+ uint8_t type;
+#define FCOE_CONN_TBL_TYPE 0xA1
+ uint8_t length; /* words */
+ uint8_t reserved[2];
+};
+
+struct lpfc_fcf_conn_rec {
+ uint16_t flags;
+#define FCFCNCT_VALID 0x0001
+#define FCFCNCT_BOOT 0x0002
+#define FCFCNCT_PRIMARY 0x0004 /* if not set, Secondary */
+#define FCFCNCT_FBNM_VALID 0x0008
+#define FCFCNCT_SWNM_VALID 0x0010
+#define FCFCNCT_VLAN_VALID 0x0020
+#define FCFCNCT_AM_VALID 0x0040
+#define FCFCNCT_AM_PREFERRED 0x0080 /* if not set, AM Required */
+#define FCFCNCT_AM_SPMA 0x0100 /* if not set, FPMA */
+
+ uint16_t vlan_tag;
+ uint8_t fabric_name[8];
+ uint8_t switch_name[8];
+};
+
+struct lpfc_fcf_conn_entry {
+ struct list_head list;
+ struct lpfc_fcf_conn_rec conn_rec;
+};
+
+/*
+ * Define the host's bootstrap mailbox. This structure contains
+ * the member attributes needed to create, use, and destroy the
+ * bootstrap mailbox region.
+ *
+ * The macro definitions for the bmbx data structure are defined
+ * in lpfc_hw4.h with the register definition.
+ */
+struct lpfc_bmbx {
+ struct lpfc_dmabuf *dmabuf;
+ struct dma_address dma_address;
+ void *avirt;
+ dma_addr_t aphys;
+ uint32_t bmbx_size;
+};
+
+#define LPFC_EQE_SIZE LPFC_EQE_SIZE_4
+
+#define LPFC_EQE_SIZE_4B 4
+#define LPFC_EQE_SIZE_16B 16
+#define LPFC_CQE_SIZE 16
+#define LPFC_WQE_SIZE 64
+#define LPFC_MQE_SIZE 256
+#define LPFC_RQE_SIZE 8
+
+#define LPFC_EQE_DEF_COUNT 1024
+#define LPFC_CQE_DEF_COUNT 256
+#define LPFC_WQE_DEF_COUNT 64
+#define LPFC_MQE_DEF_COUNT 16
+#define LPFC_RQE_DEF_COUNT 512
+
+#define LPFC_QUEUE_NOARM false
+#define LPFC_QUEUE_REARM true
+
+
+/*
+ * SLI4 CT field defines
+ */
+#define SLI4_CT_RPI 0
+#define SLI4_CT_VPI 1
+#define SLI4_CT_VFI 2
+#define SLI4_CT_FCFI 3
+
+#define LPFC_SLI4_MAX_SEGMENT_SIZE 0x10000
+
+/*
+ * SLI4 specific data structures
+ */
+struct lpfc_max_cfg_param {
+ uint16_t max_xri;
+ uint16_t xri_base;
+ uint16_t xri_used;
+ uint16_t max_rpi;
+ uint16_t rpi_base;
+ uint16_t rpi_used;
+ uint16_t max_vpi;
+ uint16_t vpi_base;
+ uint16_t vpi_used;
+ uint16_t max_vfi;
+ uint16_t vfi_base;
+ uint16_t vfi_used;
+ uint16_t max_fcfi;
+ uint16_t fcfi_base;
+ uint16_t fcfi_used;
+ uint16_t max_eq;
+ uint16_t max_rq;
+ uint16_t max_cq;
+ uint16_t max_wq;
+};
+
+struct lpfc_hba;
+/* SLI4 HBA multi-fcp queue handler struct */
+struct lpfc_fcp_eq_hdl {
+ uint32_t idx;
+ struct lpfc_hba *phba;
+};
+
+/* SLI4 HBA data structure entries */
+struct lpfc_sli4_hba {
+ void __iomem *conf_regs_memmap_p; /* Kernel memory mapped address for
+ PCI BAR0, config space registers */
+ void __iomem *ctrl_regs_memmap_p; /* Kernel memory mapped address for
+ PCI BAR1, control registers */
+ void __iomem *drbl_regs_memmap_p; /* Kernel memory mapped address for
+ PCI BAR2, doorbell registers */
+ /* BAR0 PCI config space register memory map */
+ void __iomem *UERRLOregaddr; /* Address to UERR_STATUS_LO register */
+ void __iomem *UERRHIregaddr; /* Address to UERR_STATUS_HI register */
+ void __iomem *ONLINE0regaddr; /* Address to components of internal UE */
+ void __iomem *ONLINE1regaddr; /* Address to components of internal UE */
+#define LPFC_ONLINE_NERR 0xFFFFFFFF
+ void __iomem *SCRATCHPADregaddr; /* Address to scratchpad register */
+ /* BAR1 FCoE function CSR register memory map */
+ void __iomem *STAregaddr; /* Address to HST_STATE register */
+ void __iomem *ISRregaddr; /* Address to HST_ISR register */
+ void __iomem *IMRregaddr; /* Address to HST_IMR register */
+ void __iomem *ISCRregaddr; /* Address to HST_ISCR register */
+ /* BAR2 VF-0 doorbell register memory map */
+ void __iomem *RQDBregaddr; /* Address to RQ_DOORBELL register */
+ void __iomem *WQDBregaddr; /* Address to WQ_DOORBELL register */
+ void __iomem *EQCQDBregaddr; /* Address to EQCQ_DOORBELL register */
+ void __iomem *MQDBregaddr; /* Address to MQ_DOORBELL register */
+ void __iomem *BMBXregaddr; /* Address to BootStrap MBX register */
+
+ struct msix_entry *msix_entries;
+ uint32_t cfg_eqn;
+ struct lpfc_fcp_eq_hdl *fcp_eq_hdl; /* FCP per-WQ handle */
+ /* Pointers to the constructed SLI4 queues */
+ struct lpfc_queue **fp_eq; /* Fast-path event queue */
+ struct lpfc_queue *sp_eq; /* Slow-path event queue */
+ struct lpfc_queue **fcp_wq;/* Fast-path FCP work queue */
+ struct lpfc_queue *mbx_wq; /* Slow-path MBOX work queue */
+ struct lpfc_queue *els_wq; /* Slow-path ELS work queue */
+ struct lpfc_queue *hdr_rq; /* Slow-path Header Receive queue */
+ struct lpfc_queue *dat_rq; /* Slow-path Data Receive queue */
+ struct lpfc_queue **fcp_cq;/* Fast-path FCP compl queue */
+ struct lpfc_queue *mbx_cq; /* Slow-path mailbox complete queue */
+ struct lpfc_queue *els_cq; /* Slow-path ELS response complete queue */
+ struct lpfc_queue *rxq_cq; /* Slow-path unsolicited complete queue */
+
+ /* Setup information for various queue parameters */
+ int eq_esize;
+ int eq_ecount;
+ int cq_esize;
+ int cq_ecount;
+ int wq_esize;
+ int wq_ecount;
+ int mq_esize;
+ int mq_ecount;
+ int rq_esize;
+ int rq_ecount;
+#define LPFC_SP_EQ_MAX_INTR_SEC 10000
+#define LPFC_FP_EQ_MAX_INTR_SEC 10000
+
+ uint32_t intr_enable;
+ struct lpfc_bmbx bmbx;
+ struct lpfc_max_cfg_param max_cfg_param;
+ uint16_t next_xri; /* last_xri - max_cfg_param.xri_base = used */
+ uint16_t next_rpi;
+ uint16_t scsi_xri_max;
+ uint16_t scsi_xri_cnt;
+ struct list_head lpfc_free_sgl_list;
+ struct list_head lpfc_sgl_list;
+ struct lpfc_sglq **lpfc_els_sgl_array;
+ struct list_head lpfc_abts_els_sgl_list;
+ struct lpfc_scsi_buf **lpfc_scsi_psb_array;
+ struct list_head lpfc_abts_scsi_buf_list;
+ uint32_t total_sglq_bufs;
+ struct lpfc_sglq **lpfc_sglq_active_list;
+ struct list_head lpfc_rpi_hdr_list;
+ unsigned long *rpi_bmask;
+ uint16_t rpi_count;
+ struct lpfc_sli4_flags sli4_flags;
+ struct list_head sp_rspiocb_work_queue;
+ struct list_head sp_cqe_event_pool;
+ struct list_head sp_asynce_work_queue;
+ struct list_head sp_fcp_xri_aborted_work_queue;
+ struct list_head sp_els_xri_aborted_work_queue;
+ struct list_head sp_unsol_work_queue;
+ struct lpfc_sli4_link link_state;
+ spinlock_t abts_scsi_buf_list_lock; /* list of aborted SCSI IOs */
+ spinlock_t abts_sgl_list_lock; /* list of aborted els IOs */
+};
+
+enum lpfc_sge_type {
+ GEN_BUFF_TYPE,
+ SCSI_BUFF_TYPE
+};
+
+struct lpfc_sglq {
+ /* lpfc_sglqs are used in double linked lists */
+ struct list_head list;
+ struct list_head clist;
+ enum lpfc_sge_type buff_type; /* is this a scsi sgl */
+ uint16_t iotag; /* pre-assigned IO tag */
+ uint16_t sli4_xritag; /* pre-assigned XRI, (OXID) tag. */
+ struct sli4_sge *sgl; /* pre-assigned SGL */
+ void *virt; /* virtual address. */
+ dma_addr_t phys; /* physical address */
+};
+
+struct lpfc_rpi_hdr {
+ struct list_head list;
+ uint32_t len;
+ struct lpfc_dmabuf *dmabuf;
+ uint32_t page_count;
+ uint32_t start_rpi;
+};
+
+/*
+ * SLI4 specific function prototypes
+ */
+int lpfc_pci_function_reset(struct lpfc_hba *);
+int lpfc_sli4_hba_setup(struct lpfc_hba *);
+int lpfc_sli4_hba_down(struct lpfc_hba *);
+int lpfc_sli4_config(struct lpfc_hba *, struct lpfcMboxq *, uint8_t,
+ uint8_t, uint32_t, bool);
+void lpfc_sli4_mbox_cmd_free(struct lpfc_hba *, struct lpfcMboxq *);
+void lpfc_sli4_mbx_sge_set(struct lpfcMboxq *, uint32_t, dma_addr_t, uint32_t);
+void lpfc_sli4_mbx_sge_get(struct lpfcMboxq *, uint32_t,
+ struct lpfc_mbx_sge *);
+
+void lpfc_sli4_hba_reset(struct lpfc_hba *);
+struct lpfc_queue *lpfc_sli4_queue_alloc(struct lpfc_hba *, uint32_t,
+ uint32_t);
+void lpfc_sli4_queue_free(struct lpfc_queue *);
+uint32_t lpfc_eq_create(struct lpfc_hba *, struct lpfc_queue *, uint16_t);
+uint32_t lpfc_cq_create(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *, uint32_t, uint32_t);
+uint32_t lpfc_mq_create(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *, uint32_t);
+uint32_t lpfc_wq_create(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *, uint32_t);
+uint32_t lpfc_rq_create(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *, struct lpfc_queue *, uint32_t);
+uint32_t lpfc_eq_destroy(struct lpfc_hba *, struct lpfc_queue *);
+uint32_t lpfc_cq_destroy(struct lpfc_hba *, struct lpfc_queue *);
+uint32_t lpfc_mq_destroy(struct lpfc_hba *, struct lpfc_queue *);
+uint32_t lpfc_wq_destroy(struct lpfc_hba *, struct lpfc_queue *);
+uint32_t lpfc_rq_destroy(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *);
+int lpfc_sli4_queue_setup(struct lpfc_hba *);
+void lpfc_sli4_queue_unset(struct lpfc_hba *);
+int lpfc_sli4_post_sgl(struct lpfc_hba *, dma_addr_t, dma_addr_t, uint16_t);
+int lpfc_sli4_repost_scsi_sgl_list(struct lpfc_hba *);
+int lpfc_sli4_remove_all_sgl_pages(struct lpfc_hba *);
+uint16_t lpfc_sli4_next_xritag(struct lpfc_hba *);
+int lpfc_sli4_post_async_mbox(struct lpfc_hba *);
+int lpfc_sli4_post_sgl_list(struct lpfc_hba *phba);
+int lpfc_sli4_post_scsi_sgl_block(struct lpfc_hba *, struct list_head *, int);
+struct lpfc_cq_event *__lpfc_sli4_cq_event_alloc(struct lpfc_hba *);
+struct lpfc_cq_event *lpfc_sli4_cq_event_alloc(struct lpfc_hba *);
+void __lpfc_sli4_cq_event_release(struct lpfc_hba *, struct lpfc_cq_event *);
+void lpfc_sli4_cq_event_release(struct lpfc_hba *, struct lpfc_cq_event *);
+int lpfc_sli4_init_rpi_hdrs(struct lpfc_hba *);
+int lpfc_sli4_post_rpi_hdr(struct lpfc_hba *, struct lpfc_rpi_hdr *);
+int lpfc_sli4_post_all_rpi_hdrs(struct lpfc_hba *);
+struct lpfc_rpi_hdr *lpfc_sli4_create_rpi_hdr(struct lpfc_hba *);
+void lpfc_sli4_remove_rpi_hdrs(struct lpfc_hba *);
+int lpfc_sli4_alloc_rpi(struct lpfc_hba *);
+void lpfc_sli4_free_rpi(struct lpfc_hba *, int);
+void lpfc_sli4_remove_rpis(struct lpfc_hba *);
+void lpfc_sli4_async_event_proc(struct lpfc_hba *);
+int lpfc_sli4_resume_rpi(struct lpfc_nodelist *);
+void lpfc_sli4_fcp_xri_abort_event_proc(struct lpfc_hba *);
+void lpfc_sli4_els_xri_abort_event_proc(struct lpfc_hba *);
+void lpfc_sli4_fcp_xri_aborted(struct lpfc_hba *,
+ struct sli4_wcqe_xri_aborted *);
+void lpfc_sli4_els_xri_aborted(struct lpfc_hba *,
+ struct sli4_wcqe_xri_aborted *);
+int lpfc_sli4_brdreset(struct lpfc_hba *);
+int lpfc_sli4_add_fcf_record(struct lpfc_hba *, struct fcf_record *);
+void lpfc_sli_remove_dflt_fcf(struct lpfc_hba *);
+int lpfc_sli4_get_els_iocb_cnt(struct lpfc_hba *);
+int lpfc_sli4_init_vpi(struct lpfc_hba *, uint16_t);
+uint32_t lpfc_sli4_cq_release(struct lpfc_queue *, bool);
+uint32_t lpfc_sli4_eq_release(struct lpfc_queue *, bool);
+void lpfc_sli4_fcfi_unreg(struct lpfc_hba *, uint16_t);
+int lpfc_sli4_read_fcf_record(struct lpfc_hba *, uint16_t);
+void lpfc_mbx_cmpl_read_fcf_record(struct lpfc_hba *, LPFC_MBOXQ_t *);
+int lpfc_sli4_post_status_check(struct lpfc_hba *);
+uint8_t lpfc_sli4_mbox_opcode_get(struct lpfc_hba *, struct lpfcMboxq *);
+
diff -upNr a/drivers/scsi/lpfc/lpfc_sli.c b/drivers/scsi/lpfc/lpfc_sli.c
--- a/drivers/scsi/lpfc/lpfc_sli.c 2009-05-22 13:14:55.000000000 -0400
+++ b/drivers/scsi/lpfc/lpfc_sli.c 2009-05-22 13:16:40.000000000 -0400
@@ -29,9 +29,12 @@
#include <scsi/scsi_device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_transport_fc.h>
+#include <scsi/fc/fc_fs.h>
+#include "lpfc_hw4.h"
#include "lpfc_hw.h"
#include "lpfc_sli.h"
+#include "lpfc_sli4.h"
#include "lpfc_nl.h"
#include "lpfc_disc.h"
#include "lpfc_scsi.h"
@@ -121,6 +124,76 @@ __lpfc_sli_get_iocbq(struct lpfc_hba *ph
}
/**
+ * __lpfc_clear_active_sglq - Remove the active sglq for this XRI.
+ * @phba: Pointer to HBA context object.
+ * @xritag: XRI value.
+ *
+ * This function clears the sglq pointer from the array of acive
+ * sglq's. The xritag that is passed in is used to index into the
+ * array. Before the xritag can be used it needs to be adjusted
+ * by subtracting the xribase.
+ *
+ * Returns sglq ponter = success, NULL = Failure.
+ **/
+static struct lpfc_sglq *
+__lpfc_clear_active_sglq(struct lpfc_hba *phba, uint16_t xritag)
+{
+ uint16_t adj_xri;
+ struct lpfc_sglq *sglq;
+ adj_xri = xritag - phba->sli4_hba.max_cfg_param.xri_base;
+ if (adj_xri > phba->sli4_hba.max_cfg_param.max_xri)
+ return NULL;
+ sglq = phba->sli4_hba.lpfc_sglq_active_list[adj_xri];
+ phba->sli4_hba.lpfc_sglq_active_list[adj_xri] = NULL;
+ return sglq;
+}
+
+/**
+ * __lpfc_get_active_sglq - Get the active sglq for this XRI.
+ * @phba: Pointer to HBA context object.
+ * @xritag: XRI value.
+ *
+ * This function returns the sglq pointer from the array of acive
+ * sglq's. The xritag that is passed in is used to index into the
+ * array. Before the xritag can be used it needs to be adjusted
+ * by subtracting the xribase.
+ *
+ * Returns sglq ponter = success, NULL = Failure.
+ **/
+static struct lpfc_sglq *
+__lpfc_get_active_sglq(struct lpfc_hba *phba, uint16_t xritag)
+{
+ uint16_t adj_xri;
+ struct lpfc_sglq *sglq;
+ adj_xri = xritag - phba->sli4_hba.max_cfg_param.xri_base;
+ if (adj_xri > phba->sli4_hba.max_cfg_param.max_xri)
+ return NULL;
+ sglq = phba->sli4_hba.lpfc_sglq_active_list[adj_xri];
+ return sglq;
+}
+
+/**
+ * __lpfc_sli_get_sglq - Allocates an iocb object from sgl pool
+ * @phba: Pointer to HBA context object.
+ *
+ * This function is called with hbalock held. This function
+ * Gets a new driver sglq object from the sglq list. If the
+ * list is not empty then it is successful, it returns pointer to the newly
+ * allocated sglq object else it returns NULL.
+ **/
+static struct lpfc_sglq *
+__lpfc_sli_get_sglq(struct lpfc_hba *phba)
+{
+ struct list_head *lpfc_sgl_list = &phba->sli4_hba.lpfc_sgl_list;
+ struct lpfc_sglq *sglq = NULL;
+ uint16_t adj_xri;
+ list_remove_head(lpfc_sgl_list, sglq, struct lpfc_sglq, list);
+ adj_xri = sglq->sli4_xritag - phba->sli4_hba.max_cfg_param.xri_base;
+ phba->sli4_hba.lpfc_sglq_active_list[adj_xri] = sglq;
+ return sglq;
+}
+
+/**
* lpfc_sli_get_iocbq - Allocates an iocb object from iocb pool
* @phba: Pointer to HBA context object.
*
@@ -298,6 +371,14 @@ lpfc_sli_iocb_cmd_type(uint8_t iocb_cmnd
case CMD_GEN_REQUEST64_CR:
case CMD_GEN_REQUEST64_CX:
case CMD_XMIT_ELS_RSP64_CX:
+ case DSSCMD_IWRITE64_CR:
+ case DSSCMD_IWRITE64_CX:
+ case DSSCMD_IREAD64_CR:
+ case DSSCMD_IREAD64_CX:
+ case DSSCMD_INVALIDATE_DEK:
+ case DSSCMD_SET_KEK:
+ case DSSCMD_GET_KEK_ID:
+ case DSSCMD_GEN_XFER:
type = LPFC_SOL_IOCB;
break;
case CMD_ABORT_XRI_CN:
@@ -2629,6 +2710,56 @@ lpfc_sli_brdready_s3(struct lpfc_hba *ph
return retval;
}
+/**
+ * lpfc_sli_brdready_s4 - Check for sli4 host ready status
+ * @phba: Pointer to HBA context object.
+ * @mask: Bit mask to be checked.
+ *
+ * This function checks the host status register to check if HBA is
+ * ready. This function will wait in a loop for the HBA to be ready
+ * If the HBA is not ready , the function will will reset the HBA PCI
+ * function again. The function returns 1 when HBA fail to be ready
+ * otherwise returns zero.
+ **/
+static int
+lpfc_sli_brdready_s4(struct lpfc_hba *phba, uint32_t mask)
+{
+ uint32_t status;
+ int retval = 0;
+
+ /* Read the HBA Host Status Register */
+ status = lpfc_sli4_post_status_check(phba);
+
+ if (status) {
+ phba->pport->port_state = LPFC_VPORT_UNKNOWN;
+ lpfc_sli_brdrestart(phba);
+ status = lpfc_sli4_post_status_check(phba);
+ }
+
+ /* Check to see if any errors occurred during init */
+ if (status) {
+ phba->link_state = LPFC_HBA_ERROR;
+ retval = 1;
+ } else
+ phba->sli4_hba.intr_enable = 0;
+
+ return retval;
+}
+
+/**
+ * lpfc_sli_brdready - Wrapper func for checking the hba readyness
+ * @phba: Pointer to HBA context object.
+ * @mask: Bit mask to be checked.
+ *
+ * This routine wraps the actual SLI3 or SLI4 hba readyness check routine
+ * from the API jump table function pointer from the lpfc_hba struct.
+ **/
+int
+lpfc_sli_brdready(struct lpfc_hba *phba, uint32_t mask)
+{
+ return phba->lpfc_sli_brdready(phba, mask);
+}
+
#define BARRIER_TEST_PATTERN (0xdeadbeef)
/**
@@ -2863,7 +2994,66 @@ lpfc_sli_brdreset(struct lpfc_hba *phba)
}
/**
- * lpfc_sli_brdrestart - Restart the HBA
+ * lpfc_sli4_brdreset - Reset a sli-4 HBA
+ * @phba: Pointer to HBA context object.
+ *
+ * This function resets a SLI4 HBA. This function disables PCI layer parity
+ * checking during resets the device. The caller is not required to hold
+ * any locks.
+ *
+ * This function returns 0 always.
+ **/
+int
+lpfc_sli4_brdreset(struct lpfc_hba *phba)
+{
+ struct lpfc_sli *psli = &phba->sli;
+ uint16_t cfg_value;
+ uint8_t qindx;
+
+ /* Reset HBA */
+ lpfc_printf_log(phba, KERN_INFO, LOG_SLI,
+ "0295 Reset HBA Data: x%x x%x\n",
+ phba->pport->port_state, psli->sli_flag);
+
+ /* perform board reset */
+ phba->fc_eventTag = 0;
+ phba->pport->fc_myDID = 0;
+ phba->pport->fc_prevDID = 0;
+
+ /* Turn off parity checking and serr during the physical reset */
+ pci_read_config_word(phba->pcidev, PCI_COMMAND, &cfg_value);
+ pci_write_config_word(phba->pcidev, PCI_COMMAND,
+ (cfg_value &
+ ~(PCI_COMMAND_PARITY | PCI_COMMAND_SERR)));
+
+ spin_lock_irq(&phba->hbalock);
+ psli->sli_flag &= ~(LPFC_PROCESS_LA);
+ phba->fcf.fcf_flag = 0;
+ /* Clean up the child queue list for the CQs */
+ list_del_init(&phba->sli4_hba.mbx_wq->list);
+ list_del_init(&phba->sli4_hba.els_wq->list);
+ list_del_init(&phba->sli4_hba.hdr_rq->list);
+ list_del_init(&phba->sli4_hba.dat_rq->list);
+ list_del_init(&phba->sli4_hba.mbx_cq->list);
+ list_del_init(&phba->sli4_hba.els_cq->list);
+ list_del_init(&phba->sli4_hba.rxq_cq->list);
+ for (qindx = 0; qindx < phba->cfg_fcp_wq_count; qindx++)
+ list_del_init(&phba->sli4_hba.fcp_wq[qindx]->list);
+ for (qindx = 0; qindx < phba->cfg_fcp_eq_count; qindx++)
+ list_del_init(&phba->sli4_hba.fcp_cq[qindx]->list);
+ spin_unlock_irq(&phba->hbalock);
+
+ /* Now physically reset the device */
+ lpfc_printf_log(phba, KERN_INFO, LOG_INIT,
+ "0389 Performing PCI function reset!\n");
+ /* Perform FCoE PCI function reset */
+ lpfc_pci_function_reset(phba);
+
+ return 0;
+}
+
+/**
+ * lpfc_sli_brdrestart_s3 - Restart a sli-3 hba
* @phba: Pointer to HBA context object.
*
* This function is called in the SLI initialization code path to
@@ -2875,8 +3065,8 @@ lpfc_sli_brdreset(struct lpfc_hba *phba)
* The function does not guarantee completion of MBX_RESTART mailbox
* command before the return of this function.
**/
-int
-lpfc_sli_brdrestart(struct lpfc_hba *phba)
+static int
+lpfc_sli_brdrestart_s3(struct lpfc_hba *phba)
{
MAILBOX_t *mb;
struct lpfc_sli *psli;
@@ -2915,7 +3105,7 @@ lpfc_sli_brdrestart(struct lpfc_hba *phb
lpfc_sli_brdreset(phba);
phba->pport->stopped = 0;
phba->link_state = LPFC_INIT_START;
-
+ phba->hba_flag = 0;
spin_unlock_irq(&phba->hbalock);
memset(&psli->lnk_stat_offsets, 0, sizeof(psli->lnk_stat_offsets));
@@ -2930,6 +3120,55 @@ lpfc_sli_brdrestart(struct lpfc_hba *phb
}
/**
+ * lpfc_sli_brdrestart_s4 - Restart the sli-4 hba
+ * @phba: Pointer to HBA context object.
+ *
+ * This function is called in the SLI initialization code path to restart
+ * a SLI4 HBA. The caller is not required to hold any lock.
+ * At the end of the function, it calls lpfc_hba_down_post function to
+ * free any pending commands.
+ **/
+static int
+lpfc_sli_brdrestart_s4(struct lpfc_hba *phba)
+{
+ struct lpfc_sli *psli = &phba->sli;
+
+
+ /* Restart HBA */
+ lpfc_printf_log(phba, KERN_INFO, LOG_SLI,
+ "0296 Restart HBA Data: x%x x%x\n",
+ phba->pport->port_state, psli->sli_flag);
+
+ lpfc_sli4_brdreset(phba);
+
+ spin_lock_irq(&phba->hbalock);
+ phba->pport->stopped = 0;
+ phba->link_state = LPFC_INIT_START;
+ phba->hba_flag = 0;
+ spin_unlock_irq(&phba->hbalock);
+
+ memset(&psli->lnk_stat_offsets, 0, sizeof(psli->lnk_stat_offsets));
+ psli->stats_start = get_seconds();
+
+ lpfc_hba_down_post(phba);
+
+ return 0;
+}
+
+/**
+ * lpfc_sli_brdrestart - Wrapper func for restarting hba
+ * @phba: Pointer to HBA context object.
+ *
+ * This routine wraps the actual SLI3 or SLI4 hba restart routine from the
+ * API jump table function pointer from the lpfc_hba struct.
+**/
+int
+lpfc_sli_brdrestart(struct lpfc_hba *phba)
+{
+ return phba->lpfc_sli_brdrestart(phba);
+}
+
+/**
* lpfc_sli_chipset_init - Wait for the restart of the HBA after a restart
* @phba: Pointer to HBA context object.
*
@@ -3353,6 +3592,488 @@ lpfc_sli_hba_setup_error:
return rc;
}
+/**
+ * lpfc_sli4_read_fcoe_params - Read fcoe params from conf region
+ * @phba: Pointer to HBA context object.
+ * @mboxq: mailbox pointer.
+ * This function issue a dump mailbox command to read config region
+ * 23 and parse the records in the region and populate driver
+ * data structure.
+ **/
+static int
+lpfc_sli4_read_fcoe_params(struct lpfc_hba *phba,
+ LPFC_MBOXQ_t *mboxq)
+{
+ struct lpfc_dmabuf *mp;
+ struct lpfc_mqe *mqe;
+ uint32_t data_length;
+ int rc;
+
+ /* Program the default value of vlan_id and fc_map */
+ phba->valid_vlan = 0;
+ phba->fc_map[0] = LPFC_FCOE_FCF_MAP0;
+ phba->fc_map[1] = LPFC_FCOE_FCF_MAP1;
+ phba->fc_map[2] = LPFC_FCOE_FCF_MAP2;
+
+ mqe = &mboxq->u.mqe;
+ if (lpfc_dump_fcoe_param(phba, mboxq))
+ return -ENOMEM;
+
+ mp = (struct lpfc_dmabuf *) mboxq->context1;
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
+
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):2571 Mailbox cmd x%x Status x%x "
+ "Data: x%x x%x x%x x%x x%x x%x x%x x%x x%x "
+ "x%x x%x x%x x%x x%x x%x x%x x%x x%x "
+ "CQ: x%x x%x x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ bf_get(lpfc_mqe_command, mqe),
+ bf_get(lpfc_mqe_status, mqe),
+ mqe->un.mb_words[0], mqe->un.mb_words[1],
+ mqe->un.mb_words[2], mqe->un.mb_words[3],
+ mqe->un.mb_words[4], mqe->un.mb_words[5],
+ mqe->un.mb_words[6], mqe->un.mb_words[7],
+ mqe->un.mb_words[8], mqe->un.mb_words[9],
+ mqe->un.mb_words[10], mqe->un.mb_words[11],
+ mqe->un.mb_words[12], mqe->un.mb_words[13],
+ mqe->un.mb_words[14], mqe->un.mb_words[15],
+ mqe->un.mb_words[16], mqe->un.mb_words[50],
+ mboxq->mcqe.word0,
+ mboxq->mcqe.mcqe_tag0, mboxq->mcqe.mcqe_tag1,
+ mboxq->mcqe.trailer);
+
+ if (rc) {
+ lpfc_mbuf_free(phba, mp->virt, mp->phys);
+ kfree(mp);
+ return -EIO;
+ }
+ data_length = mqe->un.mb_words[5];
+ if (data_length > DMP_FCOEPARAM_RGN_SIZE)
+ return -EIO;
+
+ lpfc_parse_fcoe_conf(phba, mp->virt, data_length);
+ lpfc_mbuf_free(phba, mp->virt, mp->phys);
+ kfree(mp);
+ return 0;
+}
+
+/**
+ * lpfc_sli4_read_rev - Issue READ_REV and collect vpd data
+ * @phba: pointer to lpfc hba data structure.
+ * @mboxq: pointer to the LPFC_MBOXQ_t structure.
+ * @vpd: pointer to the memory to hold resulting port vpd data.
+ * @vpd_size: On input, the number of bytes allocated to @vpd.
+ * On output, the number of data bytes in @vpd.
+ *
+ * This routine executes a READ_REV SLI4 mailbox command. In
+ * addition, this routine gets the port vpd data.
+ *
+ * Return codes
+ * 0 - sucessful
+ * ENOMEM - could not allocated memory.
+ **/
+static int
+lpfc_sli4_read_rev(struct lpfc_hba *phba, LPFC_MBOXQ_t *mboxq,
+ uint8_t *vpd, uint32_t *vpd_size)
+{
+ int rc = 0;
+ uint32_t dma_size;
+ struct lpfc_dmabuf *dmabuf;
+ struct lpfc_mqe *mqe;
+
+ dmabuf = kzalloc(sizeof(struct lpfc_dmabuf), GFP_KERNEL);
+ if (!dmabuf)
+ return -ENOMEM;
+
+ /*
+ * Get a DMA buffer for the vpd data resulting from the READ_REV
+ * mailbox command.
+ */
+ dma_size = *vpd_size;
+ dmabuf->virt = dma_alloc_coherent(&phba->pcidev->dev,
+ dma_size,
+ &dmabuf->phys,
+ GFP_KERNEL);
+ if (!dmabuf->virt) {
+ kfree(dmabuf);
+ return -ENOMEM;
+ }
+ memset(dmabuf->virt, 0, dma_size);
+
+ /*
+ * The SLI4 implementation of READ_REV conflicts at word1,
+ * bits 31:16 and SLI4 adds vpd functionality not present
+ * in SLI3. This code corrects the conflicts.
+ */
+ lpfc_read_rev(phba, mboxq);
+ mqe = &mboxq->u.mqe;
+ mqe->un.read_rev.vpd_paddr_high = putPaddrHigh(dmabuf->phys);
+ mqe->un.read_rev.vpd_paddr_low = putPaddrLow(dmabuf->phys);
+ mqe->un.read_rev.word1 &= 0x0000FFFF;
+ bf_set(lpfc_mbx_rd_rev_vpd, &mqe->un.read_rev, 1);
+ bf_set(lpfc_mbx_rd_rev_avail_len, &mqe->un.read_rev, dma_size);
+
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
+ if (rc) {
+ dma_free_coherent(&phba->pcidev->dev, dma_size,
+ dmabuf->virt, dmabuf->phys);
+ return -EIO;
+ }
+
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):0380 Mailbox cmd x%x Status x%x "
+ "Data: x%x x%x x%x x%x x%x x%x x%x x%x x%x "
+ "x%x x%x x%x x%x x%x x%x x%x x%x x%x "
+ "CQ: x%x x%x x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ bf_get(lpfc_mqe_command, mqe),
+ bf_get(lpfc_mqe_status, mqe),
+ mqe->un.mb_words[0], mqe->un.mb_words[1],
+ mqe->un.mb_words[2], mqe->un.mb_words[3],
+ mqe->un.mb_words[4], mqe->un.mb_words[5],
+ mqe->un.mb_words[6], mqe->un.mb_words[7],
+ mqe->un.mb_words[8], mqe->un.mb_words[9],
+ mqe->un.mb_words[10], mqe->un.mb_words[11],
+ mqe->un.mb_words[12], mqe->un.mb_words[13],
+ mqe->un.mb_words[14], mqe->un.mb_words[15],
+ mqe->un.mb_words[16], mqe->un.mb_words[50],
+ mboxq->mcqe.word0,
+ mboxq->mcqe.mcqe_tag0, mboxq->mcqe.mcqe_tag1,
+ mboxq->mcqe.trailer);
+
+ /*
+ * The available vpd length cannot be bigger than the
+ * DMA buffer passed to the port. Catch the less than
+ * case and update the caller's size.
+ */
+ if (mqe->un.read_rev.avail_vpd_len < *vpd_size)
+ *vpd_size = mqe->un.read_rev.avail_vpd_len;
+
+ lpfc_sli_pcimem_bcopy(dmabuf->virt, vpd, *vpd_size);
+ dma_free_coherent(&phba->pcidev->dev, dma_size,
+ dmabuf->virt, dmabuf->phys);
+ kfree(dmabuf);
+ return 0;
+}
+
+/**
+ * lpfc_sli4_arm_cqeq_intr - Arm sli-4 device completion and event queues
+ * @phba: pointer to lpfc hba data structure.
+ *
+ * This routine is called to explicitly arm the SLI4 device's completion and
+ * event queues
+ **/
+static void
+lpfc_sli4_arm_cqeq_intr(struct lpfc_hba *phba)
+{
+ uint8_t fcp_eqidx;
+
+ lpfc_sli4_cq_release(phba->sli4_hba.mbx_cq, LPFC_QUEUE_REARM);
+ lpfc_sli4_cq_release(phba->sli4_hba.els_cq, LPFC_QUEUE_REARM);
+ lpfc_sli4_cq_release(phba->sli4_hba.rxq_cq, LPFC_QUEUE_REARM);
+ for (fcp_eqidx = 0; fcp_eqidx < phba->cfg_fcp_eq_count; fcp_eqidx++)
+ lpfc_sli4_cq_release(phba->sli4_hba.fcp_cq[fcp_eqidx],
+ LPFC_QUEUE_REARM);
+ lpfc_sli4_eq_release(phba->sli4_hba.sp_eq, LPFC_QUEUE_REARM);
+ for (fcp_eqidx = 0; fcp_eqidx < phba->cfg_fcp_eq_count; fcp_eqidx++)
+ lpfc_sli4_eq_release(phba->sli4_hba.fp_eq[fcp_eqidx],
+ LPFC_QUEUE_REARM);
+}
+
+/**
+ * lpfc_sli4_hba_setup - SLI4 device intialization PCI function
+ * @phba: Pointer to HBA context object.
+ *
+ * This function is the main SLI4 device intialization PCI function. This
+ * function is called by the HBA intialization code, HBA reset code and
+ * HBA error attention handler code. Caller is not required to hold any
+ * locks.
+ **/
+int
+lpfc_sli4_hba_setup(struct lpfc_hba *phba)
+{
+ int rc;
+ LPFC_MBOXQ_t *mboxq;
+ struct lpfc_mqe *mqe;
+ uint8_t *vpd;
+ uint32_t vpd_size;
+ uint32_t ftr_rsp = 0;
+ struct Scsi_Host *shost = lpfc_shost_from_vport(phba->pport);
+ struct lpfc_vport *vport = phba->pport;
+ struct lpfc_dmabuf *mp;
+
+ /* Perform a PCI function reset to start from clean */
+ rc = lpfc_pci_function_reset(phba);
+ if (unlikely(rc))
+ return -ENODEV;
+
+ /* Check the HBA Host Status Register for readyness */
+ rc = lpfc_sli4_post_status_check(phba);
+ if (unlikely(rc))
+ return -ENODEV;
+ else {
+ spin_lock_irq(&phba->hbalock);
+ phba->sli.sli_flag |= LPFC_SLI_ACTIVE;
+ spin_unlock_irq(&phba->hbalock);
+ }
+
+ /*
+ * Allocate a single mailbox container for initializing the
+ * port.
+ */
+ mboxq = (LPFC_MBOXQ_t *) mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
+ if (!mboxq)
+ return -ENOMEM;
+
+ /*
+ * Continue initialization with default values even if driver failed
+ * to read FCoE param config regions
+ */
+ if (lpfc_sli4_read_fcoe_params(phba, mboxq))
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_INIT,
+ "2570 Failed to read FCoE parameters \n");
+
+ /* Issue READ_REV to collect vpd and FW information. */
+ vpd_size = PAGE_SIZE;
+ vpd = kzalloc(vpd_size, GFP_KERNEL);
+ if (!vpd) {
+ rc = -ENOMEM;
+ goto out_free_mbox;
+ }
+
+ rc = lpfc_sli4_read_rev(phba, mboxq, vpd, &vpd_size);
+ if (unlikely(rc))
+ goto out_free_vpd;
+
+ mqe = &mboxq->u.mqe;
+ if ((bf_get(lpfc_mbx_rd_rev_sli_lvl,
+ &mqe->un.read_rev) != LPFC_SLI_REV4) ||
+ (bf_get(lpfc_mbx_rd_rev_fcoe, &mqe->un.read_rev) == 0)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0376 READ_REV Error. SLI Level %d "
+ "FCoE enabled %d\n",
+ bf_get(lpfc_mbx_rd_rev_sli_lvl, &mqe->un.read_rev),
+ bf_get(lpfc_mbx_rd_rev_fcoe, &mqe->un.read_rev));
+ rc = -EIO;
+ goto out_free_vpd;
+ }
+ /* Single threaded at this point, no need for lock */
+ spin_lock_irq(&phba->hbalock);
+ phba->hba_flag |= HBA_FCOE_SUPPORT;
+ spin_unlock_irq(&phba->hbalock);
+ /*
+ * Evaluate the read rev and vpd data. Populate the driver
+ * state with the results. If this routine fails, the failure
+ * is not fatal as the driver will use generic values.
+ */
+ rc = lpfc_parse_vpd(phba, vpd, vpd_size);
+ if (unlikely(!rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0377 Error %d parsing vpd. "
+ "Using defaults.\n", rc);
+ rc = 0;
+ }
+
+ /* By now, we should determine the SLI revision, hard code for now */
+ phba->sli_rev = LPFC_SLI_REV4;
+
+ /*
+ * Discover the port's supported feature set and match it against the
+ * hosts requests.
+ */
+ lpfc_request_features(phba, mboxq);
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
+ if (unlikely(rc)) {
+ rc = -EIO;
+ goto out_free_vpd;
+ }
+
+ /*
+ * The port must support FCP initiator mode as this is the
+ * only mode running in the host.
+ */
+ if (!(bf_get(lpfc_mbx_rq_ftr_rsp_fcpi, &mqe->un.req_ftrs))) {
+ lpfc_printf_log(phba, KERN_WARNING, LOG_MBOX | LOG_SLI,
+ "0378 No support for fcpi mode.\n");
+ ftr_rsp++;
+ }
+
+ /*
+ * If the port cannot support the host's requested features
+ * then turn off the global config parameters to disable the
+ * feature in the driver. This is not a fatal error.
+ */
+ if ((phba->cfg_enable_bg) &&
+ !(bf_get(lpfc_mbx_rq_ftr_rsp_dif, &mqe->un.req_ftrs)))
+ ftr_rsp++;
+
+ if (phba->max_vpi && phba->cfg_enable_npiv &&
+ !(bf_get(lpfc_mbx_rq_ftr_rsp_npiv, &mqe->un.req_ftrs)))
+ ftr_rsp++;
+
+ if (ftr_rsp) {
+ lpfc_printf_log(phba, KERN_WARNING, LOG_MBOX | LOG_SLI,
+ "0379 Feature Mismatch Data: x%08x %08x "
+ "x%x x%x x%x\n", mqe->un.req_ftrs.word2,
+ mqe->un.req_ftrs.word3, phba->cfg_enable_bg,
+ phba->cfg_enable_npiv, phba->max_vpi);
+ if (!(bf_get(lpfc_mbx_rq_ftr_rsp_dif, &mqe->un.req_ftrs)))
+ phba->cfg_enable_bg = 0;
+ if (!(bf_get(lpfc_mbx_rq_ftr_rsp_npiv, &mqe->un.req_ftrs)))
+ phba->cfg_enable_npiv = 0;
+ }
+
+ /* These SLI3 features are assumed in SLI4 */
+ spin_lock_irq(&phba->hbalock);
+ phba->sli3_options |= (LPFC_SLI3_NPIV_ENABLED | LPFC_SLI3_HBQ_ENABLED);
+ spin_unlock_irq(&phba->hbalock);
+
+ /* Read the port's service parameters. */
+ lpfc_read_sparam(phba, mboxq, vport->vpi);
+ mboxq->vport = vport;
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
+ mp = (struct lpfc_dmabuf *) mboxq->context1;
+ if (rc == MBX_SUCCESS) {
+ memcpy(&vport->fc_sparam, mp->virt, sizeof(struct serv_parm));
+ rc = 0;
+ }
+
+ /*
+ * This memory was allocated by the lpfc_read_sparam routine. Release
+ * it to the mbuf pool.
+ */
+ lpfc_mbuf_free(phba, mp->virt, mp->phys);
+ kfree(mp);
+ mboxq->context1 = NULL;
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0382 READ_SPARAM command failed "
+ "status %d, mbxStatus x%x\n",
+ rc, bf_get(lpfc_mqe_status, mqe));
+ phba->link_state = LPFC_HBA_ERROR;
+ rc = -EIO;
+ goto out_free_vpd;
+ }
+
+ if (phba->cfg_soft_wwnn)
+ u64_to_wwn(phba->cfg_soft_wwnn,
+ vport->fc_sparam.nodeName.u.wwn);
+ if (phba->cfg_soft_wwpn)
+ u64_to_wwn(phba->cfg_soft_wwpn,
+ vport->fc_sparam.portName.u.wwn);
+ memcpy(&vport->fc_nodename, &vport->fc_sparam.nodeName,
+ sizeof(struct lpfc_name));
+ memcpy(&vport->fc_portname, &vport->fc_sparam.portName,
+ sizeof(struct lpfc_name));
+
+ /* Update the fc_host data structures with new wwn. */
+ fc_host_node_name(shost) = wwn_to_u64(vport->fc_nodename.u.wwn);
+ fc_host_port_name(shost) = wwn_to_u64(vport->fc_portname.u.wwn);
+
+ /* Register SGL pool to the device using non-embedded mailbox command */
+ rc = lpfc_sli4_post_sgl_list(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0582 Error %d during sgl post operation", rc);
+ rc = -ENODEV;
+ goto out_free_vpd;
+ }
+
+ /* Register SCSI SGL pool to the device */
+ rc = lpfc_sli4_repost_scsi_sgl_list(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_WARNING, LOG_MBOX | LOG_SLI,
+ "0383 Error %d during scsi sgl post opeation",
+ rc);
+ /* Some Scsi buffers were moved to the abort scsi list */
+ /* A pci function reset will repost them */
+ rc = -ENODEV;
+ goto out_free_vpd;
+ }
+
+ /* Post the rpi header region to the device. */
+ rc = lpfc_sli4_post_all_rpi_hdrs(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0393 Error %d during rpi post operation\n",
+ rc);
+ rc = -ENODEV;
+ goto out_free_vpd;
+ }
+ /* Temporary initialization of lpfc_fip_flag to non-fip */
+ bf_set(lpfc_fip_flag, &phba->sli4_hba.sli4_flags, 0);
+
+ /* Set up all the queues to the device */
+ rc = lpfc_sli4_queue_setup(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0381 Error %d during queue setup.\n ", rc);
+ goto out_stop_timers;
+ }
+
+ /* Arm the CQs and then EQs on device */
+ lpfc_sli4_arm_cqeq_intr(phba);
+
+ /* Indicate device interrupt mode */
+ phba->sli4_hba.intr_enable = 1;
+
+ /* Allow asynchronous mailbox command to go through */
+ spin_lock_irq(&phba->hbalock);
+ phba->sli.sli_flag &= ~LPFC_SLI_ASYNC_MBX_BLK;
+ spin_unlock_irq(&phba->hbalock);
+
+ /* Post receive buffers to the device */
+ lpfc_sli4_rb_setup(phba);
+
+ /* Start the ELS watchdog timer */
+ /*
+ * The driver for SLI4 is not yet ready to process timeouts
+ * or interrupts. Once it is, the comment bars can be removed.
+ */
+ /* mod_timer(&vport->els_tmofunc,
+ * jiffies + HZ * (phba->fc_ratov*2)); */
+
+ /* Start heart beat timer */
+ mod_timer(&phba->hb_tmofunc,
+ jiffies + HZ * LPFC_HB_MBOX_INTERVAL);
+ phba->hb_outstanding = 0;
+ phba->last_completion_time = jiffies;
+
+ /* Start error attention (ERATT) polling timer */
+ mod_timer(&phba->eratt_poll, jiffies + HZ * LPFC_ERATT_POLL_INTERVAL);
+
+ /*
+ * The port is ready, set the host's link state to LINK_DOWN
+ * in preparation for link interrupts.
+ */
+ lpfc_init_link(phba, mboxq, phba->cfg_topology, phba->cfg_link_speed);
+ mboxq->mbox_cmpl = lpfc_sli_def_mbox_cmpl;
+ lpfc_set_loopback_flag(phba);
+ /* Change driver state to LPFC_LINK_DOWN right before init link */
+ spin_lock_irq(&phba->hbalock);
+ phba->link_state = LPFC_LINK_DOWN;
+ spin_unlock_irq(&phba->hbalock);
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_NOWAIT);
+ if (unlikely(rc != MBX_NOT_FINISHED)) {
+ kfree(vpd);
+ return 0;
+ } else
+ rc = -EIO;
+
+ /* Unset all the queues set up in this routine when error out */
+ if (rc)
+ lpfc_sli4_queue_unset(phba);
+
+out_stop_timers:
+ if (rc)
+ lpfc_stop_hba_timers(phba);
+out_free_vpd:
+ kfree(vpd);
+out_free_mbox:
+ mempool_free(mboxq, phba->mbox_mem_pool);
+ return rc;
+}
/**
* lpfc_mbox_timeout - Timeout call back function for mbox timer
@@ -3812,13 +4533,420 @@ lpfc_sli_issue_mbox_s3(struct lpfc_hba *
out_not_finished:
if (processing_queue) {
- pmbox->mb.mbxStatus = MBX_NOT_FINISHED;
+ pmbox->u.mb.mbxStatus = MBX_NOT_FINISHED;
lpfc_mbox_cmpl_put(phba, pmbox);
}
return MBX_NOT_FINISHED;
}
/**
+ * lpfc_sli4_post_sync_mbox - Post an SLI4 mailbox to the bootstrap mailbox
+ * @phba: Pointer to HBA context object.
+ * @mboxq: Pointer to mailbox object.
+ *
+ * The function posts a mailbox to the port. The mailbox is expected
+ * to be comletely filled in and ready for the port to operate on it.
+ * This routine executes a synchronous completion operation on the
+ * mailbox by polling for its completion.
+ *
+ * The caller must not be holding any locks when calling this routine.
+ *
+ * Returns:
+ * MBX_SUCCESS - mailbox posted successfully
+ * Any of the MBX error values.
+ **/
+static int
+lpfc_sli4_post_sync_mbox(struct lpfc_hba *phba, LPFC_MBOXQ_t *mboxq)
+{
+ int rc = MBX_SUCCESS;
+ unsigned long iflag;
+ uint32_t db_ready;
+ uint32_t mcqe_status;
+ uint32_t mbx_cmnd;
+ unsigned long timeout;
+ struct lpfc_sli *psli = &phba->sli;
+ struct lpfc_mqe *mb = &mboxq->u.mqe;
+ struct lpfc_bmbx_create *mbox_rgn;
+ struct dma_address *dma_address;
+ struct lpfc_register bmbx_reg;
+
+ /*
+ * Only one mailbox can be active to the bootstrap mailbox region
+ * at a time and there is no queueing provided.
+ */
+ spin_lock_irqsave(&phba->hbalock, iflag);
+ if (psli->sli_flag & LPFC_SLI_MBOX_ACTIVE) {
+ spin_unlock_irqrestore(&phba->hbalock, iflag);
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2532 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, MBX_POLL);
+ return MBXERR_ERROR;
+ }
+ /* The server grabs the token and owns it until release */
+ psli->sli_flag |= LPFC_SLI_MBOX_ACTIVE;
+ phba->sli.mbox_active = mboxq;
+ spin_unlock_irqrestore(&phba->hbalock, iflag);
+
+ /*
+ * Initialize the bootstrap memory region to avoid stale data areas
+ * in the mailbox post. Then copy the caller's mailbox contents to
+ * the bmbx mailbox region.
+ */
+ mbx_cmnd = bf_get(lpfc_mqe_command, mb);
+ memset(phba->sli4_hba.bmbx.avirt, 0, sizeof(struct lpfc_bmbx_create));
+ lpfc_sli_pcimem_bcopy(mb, phba->sli4_hba.bmbx.avirt,
+ sizeof(struct lpfc_mqe));
+
+ /* Post the high mailbox dma address to the port and wait for ready. */
+ dma_address = &phba->sli4_hba.bmbx.dma_address;
+ writel(dma_address->addr_hi, phba->sli4_hba.BMBXregaddr);
+
+ timeout = msecs_to_jiffies(lpfc_mbox_tmo_val(phba, mbx_cmnd)
+ * 1000) + jiffies;
+ do {
+ bmbx_reg.word0 = readl(phba->sli4_hba.BMBXregaddr);
+ db_ready = bf_get(lpfc_bmbx_rdy, &bmbx_reg);
+ if (!db_ready)
+ msleep(2);
+
+ if (time_after(jiffies, timeout)) {
+ rc = MBXERR_ERROR;
+ goto exit;
+ }
+ } while (!db_ready);
+
+ /* Post the low mailbox dma address to the port. */
+ writel(dma_address->addr_lo, phba->sli4_hba.BMBXregaddr);
+ timeout = msecs_to_jiffies(lpfc_mbox_tmo_val(phba, mbx_cmnd)
+ * 1000) + jiffies;
+ do {
+ bmbx_reg.word0 = readl(phba->sli4_hba.BMBXregaddr);
+ db_ready = bf_get(lpfc_bmbx_rdy, &bmbx_reg);
+ if (!db_ready)
+ msleep(2);
+
+ if (time_after(jiffies, timeout)) {
+ rc = MBXERR_ERROR;
+ goto exit;
+ }
+ } while (!db_ready);
+
+ /*
+ * Read the CQ to ensure the mailbox has completed.
+ * If so, update the mailbox status so that the upper layers
+ * can complete the request normally.
+ */
+ lpfc_sli_pcimem_bcopy(phba->sli4_hba.bmbx.avirt, mb,
+ sizeof(struct lpfc_mqe));
+ mbox_rgn = (struct lpfc_bmbx_create *) phba->sli4_hba.bmbx.avirt;
+ lpfc_sli_pcimem_bcopy(&mbox_rgn->mcqe, &mboxq->mcqe,
+ sizeof(struct lpfc_mcqe));
+ mcqe_status = bf_get(lpfc_mcqe_status, &mbox_rgn->mcqe);
+
+ /* Prefix the mailbox status with range x4000 to note SLI4 status. */
+ if (mcqe_status != MB_CQE_STATUS_SUCCESS) {
+ bf_set(lpfc_mqe_status, mb, LPFC_MBX_ERROR_RANGE | mcqe_status);
+ rc = MBXERR_ERROR;
+ }
+
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):0356 Mailbox cmd x%x (x%x) Status x%x "
+ "Data: x%x x%x x%x x%x x%x x%x x%x x%x x%x x%x x%x"
+ " x%x x%x CQ: x%x x%x x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mbx_cmnd, lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ bf_get(lpfc_mqe_status, mb),
+ mb->un.mb_words[0], mb->un.mb_words[1],
+ mb->un.mb_words[2], mb->un.mb_words[3],
+ mb->un.mb_words[4], mb->un.mb_words[5],
+ mb->un.mb_words[6], mb->un.mb_words[7],
+ mb->un.mb_words[8], mb->un.mb_words[9],
+ mb->un.mb_words[10], mb->un.mb_words[11],
+ mb->un.mb_words[12], mboxq->mcqe.word0,
+ mboxq->mcqe.mcqe_tag0, mboxq->mcqe.mcqe_tag1,
+ mboxq->mcqe.trailer);
+exit:
+ /* We are holding the token, no needed for lock when release */
+ spin_lock_irqsave(&phba->hbalock, iflag);
+ psli->sli_flag &= ~LPFC_SLI_MBOX_ACTIVE;
+ phba->sli.mbox_active = NULL;
+ spin_unlock_irqrestore(&phba->hbalock, iflag);
+ return rc;
+}
+
+/**
+ * lpfc_sli_issue_mbox_s4 - Issue an SLI4 mailbox command to firmware
+ * @phba: Pointer to HBA context object.
+ * @pmbox: Pointer to mailbox object.
+ * @flag: Flag indicating how the mailbox need to be processed.
+ *
+ * This function is called by discovery code and HBA management code to submit
+ * a mailbox command to firmware with SLI-4 interface spec.
+ *
+ * Return codes the caller owns the mailbox command after the return of the
+ * function.
+ **/
+static int
+lpfc_sli_issue_mbox_s4(struct lpfc_hba *phba, LPFC_MBOXQ_t *mboxq,
+ uint32_t flag)
+{
+ struct lpfc_sli *psli = &phba->sli;
+ unsigned long iflags;
+ int rc;
+
+ /* Detect polling mode and jump to a handler */
+ if (!phba->sli4_hba.intr_enable) {
+ if (flag == MBX_POLL)
+ rc = lpfc_sli4_post_sync_mbox(phba, mboxq);
+ else
+ rc = -EIO;
+ if (rc != MBX_SUCCESS)
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2541 Mailbox command x%x "
+ "(x%x) cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, flag);
+ return rc;
+ } else if (flag == MBX_POLL) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2542 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, flag);
+ return -EIO;
+ }
+
+ /* Now, interrupt mode asynchrous mailbox command */
+ rc = lpfc_mbox_cmd_check(phba, mboxq);
+ if (rc) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2543 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, flag);
+ goto out_not_finished;
+ }
+ rc = lpfc_mbox_dev_check(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2544 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, flag);
+ goto out_not_finished;
+ }
+
+ /* Put the mailbox command to the driver internal FIFO */
+ psli->slistat.mbox_busy++;
+ spin_lock_irqsave(&phba->hbalock, iflags);
+ lpfc_mbox_put(phba, mboxq);
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):0354 Mbox cmd issue - Enqueue Data: "
+ "x%x (x%x) x%x x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0xffffff,
+ bf_get(lpfc_mqe_command, &mboxq->u.mqe),
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ phba->pport->port_state,
+ psli->sli_flag, MBX_NOWAIT);
+ /* Wake up worker thread to transport mailbox command from head */
+ lpfc_worker_wake_up(phba);
+
+ return MBX_BUSY;
+
+out_not_finished:
+ return MBX_NOT_FINISHED;
+}
+
+/**
+ * lpfc_sli4_post_async_mbox - Post an SLI4 mailbox command to device
+ * @phba: Pointer to HBA context object.
+ *
+ * This function is called by worker thread to send a mailbox command to
+ * SLI4 HBA firmware.
+ *
+ **/
+int
+lpfc_sli4_post_async_mbox(struct lpfc_hba *phba)
+{
+ struct lpfc_sli *psli = &phba->sli;
+ LPFC_MBOXQ_t *mboxq;
+ int rc = MBX_SUCCESS;
+ unsigned long iflags;
+ struct lpfc_mqe *mqe;
+ uint32_t mbx_cmnd;
+
+ /* Check interrupt mode before post async mailbox command */
+ if (unlikely(!phba->sli4_hba.intr_enable))
+ return MBX_NOT_FINISHED;
+
+ /* Check for mailbox command service token */
+ spin_lock_irqsave(&phba->hbalock, iflags);
+ if (unlikely(psli->sli_flag & LPFC_SLI_ASYNC_MBX_BLK)) {
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ return MBX_NOT_FINISHED;
+ }
+ if (psli->sli_flag & LPFC_SLI_MBOX_ACTIVE) {
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ return MBX_NOT_FINISHED;
+ }
+ if (unlikely(phba->sli.mbox_active)) {
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0384 There is pending active mailbox cmd\n");
+ return MBX_NOT_FINISHED;
+ }
+ /* Take the mailbox command service token */
+ psli->sli_flag |= LPFC_SLI_MBOX_ACTIVE;
+
+ /* Get the next mailbox command from head of queue */
+ mboxq = lpfc_mbox_get(phba);
+
+ /* If no more mailbox command waiting for post, we're done */
+ if (!mboxq) {
+ psli->sli_flag &= ~LPFC_SLI_MBOX_ACTIVE;
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ return MBX_SUCCESS;
+ }
+ phba->sli.mbox_active = mboxq;
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+
+ /* Check device readiness for posting mailbox command */
+ rc = lpfc_mbox_dev_check(phba);
+ if (unlikely(rc))
+ /* Driver clean routine will clean up pending mailbox */
+ goto out_not_finished;
+
+ /* Prepare the mbox command to be posted */
+ mqe = &mboxq->u.mqe;
+ mbx_cmnd = bf_get(lpfc_mqe_command, mqe);
+
+ /* Start timer for the mbox_tmo and log some mailbox post messages */
+ mod_timer(&psli->mbox_tmo, (jiffies +
+ (HZ * lpfc_mbox_tmo_val(phba, mbx_cmnd))));
+
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):0355 Mailbox cmd x%x (x%x) issue Data: "
+ "x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0, mbx_cmnd,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ phba->pport->port_state, psli->sli_flag);
+
+ if (mbx_cmnd != MBX_HEARTBEAT) {
+ if (mboxq->vport) {
+ lpfc_debugfs_disc_trc(mboxq->vport,
+ LPFC_DISC_TRC_MBOX_VPORT,
+ "MBOX Send vport: cmd:x%x mb:x%x x%x",
+ mbx_cmnd, mqe->un.mb_words[0],
+ mqe->un.mb_words[1]);
+ } else {
+ lpfc_debugfs_disc_trc(phba->pport,
+ LPFC_DISC_TRC_MBOX,
+ "MBOX Send: cmd:x%x mb:x%x x%x",
+ mbx_cmnd, mqe->un.mb_words[0],
+ mqe->un.mb_words[1]);
+ }
+ }
+ psli->slistat.mbox_cmd++;
+
+ /* Post the mailbox command to the port */
+ rc = lpfc_sli4_mq_put(phba->sli4_hba.mbx_wq, mqe);
+ if (rc != MBX_SUCCESS) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2533 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, MBX_NOWAIT);
+ goto out_not_finished;
+ }
+
+ return rc;
+
+out_not_finished:
+ spin_lock_irqsave(&phba->hbalock, iflags);
+ mboxq->u.mb.mbxStatus = MBX_NOT_FINISHED;
+ __lpfc_mbox_cmpl_put(phba, mboxq);
+ /* Release the token */
+ psli->sli_flag &= ~LPFC_SLI_MBOX_ACTIVE;
+ phba->sli.mbox_active = NULL;
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+
+ return MBX_NOT_FINISHED;
+}
+
+/**
+ * lpfc_sli_issue_mbox - Wrapper func for issuing mailbox command
+ * @phba: Pointer to HBA context object.
+ * @pmbox: Pointer to mailbox object.
+ * @flag: Flag indicating how the mailbox need to be processed.
+ *
+ * This routine wraps the actual SLI3 or SLI4 mailbox issuing routine from
+ * the API jump table function pointer from the lpfc_hba struct.
+ *
+ * Return codes the caller owns the mailbox command after the return of the
+ * function.
+ **/
+int
+lpfc_sli_issue_mbox(struct lpfc_hba *phba, LPFC_MBOXQ_t *pmbox, uint32_t flag)
+{
+ return phba->lpfc_sli_issue_mbox(phba, pmbox, flag);
+}
+
+/**
+ * lpfc_mbox_api_table_setup - Set up mbox api fucntion jump table
+ * @phba: The hba struct for which this call is being executed.
+ * @dev_grp: The HBA PCI-Device group number.
+ *
+ * This routine sets up the mbox interface API function jump table in @phba
+ * struct.
+ * Returns: 0 - success, -ENODEV - failure.
+ **/
+int
+lpfc_mbox_api_table_setup(struct lpfc_hba *phba, uint8_t dev_grp)
+{
+
+ switch (dev_grp) {
+ case LPFC_PCI_DEV_LP:
+ phba->lpfc_sli_issue_mbox = lpfc_sli_issue_mbox_s3;
+ phba->lpfc_sli_handle_slow_ring_event =
+ lpfc_sli_handle_slow_ring_event_s3;
+ phba->lpfc_sli_hbq_to_firmware = lpfc_sli_hbq_to_firmware_s3;
+ phba->lpfc_sli_brdrestart = lpfc_sli_brdrestart_s3;
+ phba->lpfc_sli_brdready = lpfc_sli_brdready_s3;
+ break;
+ case LPFC_PCI_DEV_OC:
+ phba->lpfc_sli_issue_mbox = lpfc_sli_issue_mbox_s4;
+ phba->lpfc_sli_handle_slow_ring_event =
+ lpfc_sli_handle_slow_ring_event_s4;
+ phba->lpfc_sli_hbq_to_firmware = lpfc_sli_hbq_to_firmware_s4;
+ phba->lpfc_sli_brdrestart = lpfc_sli_brdrestart_s4;
+ phba->lpfc_sli_brdready = lpfc_sli_brdready_s4;
+ break;
+ default:
+ lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
+ "1420 Invalid HBA PCI-device group: 0x%x\n",
+ dev_grp);
+ return -ENODEV;
+ break;
+ }
+ return 0;
+}
+
+/**
* __lpfc_sli_ringtx_put - Add an iocb to the txq
* @phba: Pointer to HBA context object.
* @pring: Pointer to driver SLI ring object.
@@ -4501,28 +5629,42 @@ lpfc_sli_hba_down(struct lpfc_hba *phba)
/* Return any active mbox cmds */
del_timer_sync(&psli->mbox_tmo);
- spin_lock_irqsave(&phba->hbalock, flags);
- spin_lock(&phba->pport->work_port_lock);
+ spin_lock_irqsave(&phba->pport->work_port_lock, flags);
phba->pport->work_port_events &= ~WORKER_MBOX_TMO;
- spin_unlock(&phba->pport->work_port_lock);
+ spin_unlock_irqrestore(&phba->pport->work_port_lock, flags);
- /* Return any pending or completed mbox cmds */
- list_splice_init(&phba->sli.mboxq, &completions);
- if (psli->mbox_active) {
- list_add_tail(&psli->mbox_active->list, &completions);
- psli->mbox_active = NULL;
- psli->sli_flag &= ~LPFC_SLI_MBOX_ACTIVE;
- }
- list_splice_init(&phba->sli.mboxq_cmpl, &completions);
- spin_unlock_irqrestore(&phba->hbalock, flags);
+ return 1;
+}
+
+/**
+ * lpfc_sli4_hba_down - PCI function resource cleanup for the SLI4 HBA
+ * @phba: Pointer to HBA context object.
+ *
+ * This function cleans up all queues, iocb, buffers, mailbox commands while
+ * shutting down the SLI4 HBA FCoE function. This function is called with no
+ * lock held and always returns 1.
+ *
+ * This function does the following to cleanup driver FCoE function resources:
+ * - Free discovery resources for each virtual port
+ * - Cleanup any pending fabric iocbs
+ * - Iterate through the iocb txq and free each entry in the list.
+ * - Free up any buffer posted to the HBA.
+ * - Clean up all the queue entries: WQ, RQ, MQ, EQ, CQ, etc.
+ * - Free mailbox commands in the mailbox queue.
+ **/
+int
+lpfc_sli4_hba_down(struct lpfc_hba *phba)
+{
+ /* Stop the SLI4 device port */
+ lpfc_stop_port(phba);
+
+ /* Tear down the queues in the HBA */
+ lpfc_sli4_queue_unset(phba);
+
+ /* unregister default FCFI from the HBA */
+ lpfc_sli4_fcfi_unreg(phba, phba->fcf.fcfi);
- while (!list_empty(&completions)) {
- list_remove_head(&completions, pmb, LPFC_MBOXQ_t, list);
- pmb->mb.mbxStatus = MBX_NOT_FINISHED;
- if (pmb->mbox_cmpl)
- pmb->mbox_cmpl(phba,pmb);
- }
return 1;
}
@@ -4853,7 +5995,10 @@ lpfc_sli_issue_abort_iotag(struct lpfc_h
iabt = &abtsiocbp->iocb;
iabt->un.acxri.abortType = ABORT_TYPE_ABTS;
iabt->un.acxri.abortContextTag = icmd->ulpContext;
- iabt->un.acxri.abortIoTag = icmd->ulpIoTag;
+ if (phba->sli_rev == LPFC_SLI_REV4)
+ iabt->un.acxri.abortIoTag = cmdiocb->sli4_xritag;
+ else
+ iabt->un.acxri.abortIoTag = icmd->ulpIoTag;
iabt->ulpLe = 1;
iabt->ulpClass = icmd->ulpClass;
@@ -4869,7 +6014,7 @@ lpfc_sli_issue_abort_iotag(struct lpfc_h
"abort cmd iotag x%x\n",
iabt->un.acxri.abortContextTag,
iabt->un.acxri.abortIoTag, abtsiocbp->iotag);
- retval = __lpfc_sli_issue_iocb(phba, pring, abtsiocbp, 0);
+ retval = __lpfc_sli_issue_iocb(phba, pring->ringno, abtsiocbp, 0);
if (retval)
__lpfc_sli_release_iocbq(phba, abtsiocbp);
@@ -5052,7 +6197,10 @@ lpfc_sli_abort_iocb(struct lpfc_vport *v
cmd = &iocbq->iocb;
abtsiocb->iocb.un.acxri.abortType = ABORT_TYPE_ABTS;
abtsiocb->iocb.un.acxri.abortContextTag = cmd->ulpContext;
- abtsiocb->iocb.un.acxri.abortIoTag = cmd->ulpIoTag;
+ if (phba->sli_rev == LPFC_SLI_REV4)
+ abtsiocb->iocb.un.acxri.abortIoTag = iocbq->sli4_xritag;
+ else
+ abtsiocb->iocb.un.acxri.abortIoTag = cmd->ulpIoTag;
abtsiocb->iocb.ulpLe = 1;
abtsiocb->iocb.ulpClass = cmd->ulpClass;
abtsiocb->vport = phba->pport;
@@ -5064,7 +6212,8 @@ lpfc_sli_abort_iocb(struct lpfc_vport *v
/* Setup callback routine and issue the command. */
abtsiocb->iocb_cmpl = lpfc_sli_abort_fcp_cmpl;
- ret_val = lpfc_sli_issue_iocb(phba, pring, abtsiocb, 0);
+ ret_val = lpfc_sli_issue_iocb(phba, pring->ringno,
+ abtsiocb, 0);
if (ret_val == IOCB_ERROR) {
lpfc_sli_release_iocbq(phba, abtsiocb);
errcnt++;
@@ -5145,7 +6294,7 @@ lpfc_sli_wake_iocb_wait(struct lpfc_hba
**/
int
lpfc_sli_issue_iocb_wait(struct lpfc_hba *phba,
- struct lpfc_sli_ring *pring,
+ uint32_t ring_number,
struct lpfc_iocbq *piocb,
struct lpfc_iocbq *prspiocbq,
uint32_t timeout)
@@ -5176,7 +6325,7 @@ lpfc_sli_issue_iocb_wait(struct lpfc_hba
readl(phba->HCregaddr); /* flush */
}
- retval = lpfc_sli_issue_iocb(phba, pring, piocb, 0);
+ retval = lpfc_sli_issue_iocb(phba, ring_number, piocb, 0);
if (retval == IOCB_SUCCESS) {
timeout_req = timeout * HZ;
timeleft = wait_event_timeout(done_q,
@@ -5385,6 +6534,58 @@ lpfc_sli_eratt_read(struct lpfc_hba *phb
}
/**
+ * lpfc_sli4_eratt_read - read sli-4 error attention events
+ * @phba: Pointer to HBA context.
+ *
+ * This function is called to read the SLI4 device error attention registers
+ * for possible error attention events. The caller must hold the hostlock
+ * with spin_lock_irq().
+ *
+ * This fucntion returns 1 when there is Error Attention in the Host Attention
+ * Register and returns 0 otherwise.
+ **/
+static int
+lpfc_sli4_eratt_read(struct lpfc_hba *phba)
+{
+ uint32_t uerr_sta_hi, uerr_sta_lo;
+ uint32_t onlnreg0, onlnreg1;
+
+ /* For now, use the SLI4 device internal unrecoverable error
+ * registers for error attention. This can be changed later.
+ */
+ onlnreg0 = readl(phba->sli4_hba.ONLINE0regaddr);
+ onlnreg1 = readl(phba->sli4_hba.ONLINE1regaddr);
+ if ((onlnreg0 != LPFC_ONLINE_NERR) || (onlnreg1 != LPFC_ONLINE_NERR)) {
+ uerr_sta_lo = readl(phba->sli4_hba.UERRLOregaddr);
+ uerr_sta_hi = readl(phba->sli4_hba.UERRHIregaddr);
+ if (uerr_sta_lo || uerr_sta_hi) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
+ "1423 HBA Unrecoverable error: "
+ "uerr_lo_reg=0x%x, uerr_hi_reg=0x%x, "
+ "online0_reg=0x%x, online1_reg=0x%x\n",
+ uerr_sta_lo, uerr_sta_hi,
+ onlnreg0, onlnreg1);
+ /* TEMP: as the driver error recover logic is not
+ * fully developed, we just log the error message
+ * and the device error attention action is now
+ * temporarily disabled.
+ */
+ return 0;
+ phba->work_status[0] = uerr_sta_lo;
+ phba->work_status[1] = uerr_sta_hi;
+ spin_lock_irq(&phba->hbalock);
+ /* Set the driver HA work bitmap */
+ phba->work_ha |= HA_ERATT;
+ /* Indicate polling handles this ERATT */
+ phba->hba_flag |= HBA_ERATT_HANDLED;
+ spin_unlock_irq(&phba->hbalock);
+ return 1;
+ }
+ }
+ return 0;
+}
+
+/**
* lpfc_sli_check_eratt - check error attention events
* @phba: Pointer to HBA context.
*
@@ -5434,6 +6635,10 @@ lpfc_sli_check_eratt(struct lpfc_hba *ph
/* Read chip Host Attention (HA) register */
ha_copy = lpfc_sli_eratt_read(phba);
break;
+ case LPFC_SLI_REV4:
+ /* Read devcie Uncoverable Error (UERR) registers */
+ ha_copy = lpfc_sli4_eratt_read(phba);
+ break;
default:
lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
"0299 Invalid SLI revision (%d)\n",
diff -upNr a/drivers/scsi/lpfc/lpfc_sli.h b/drivers/scsi/lpfc/lpfc_sli.h
--- a/drivers/scsi/lpfc/lpfc_sli.h 2008-10-18 10:32:52.000000000 -0400
+++ b/drivers/scsi/lpfc/lpfc_sli.h 2009-05-22 13:16:40.000000000 -0400
@@ -29,13 +29,23 @@ typedef enum _lpfc_ctx_cmd {
LPFC_CTX_HOST
} lpfc_ctx_cmd;
+/* This structure is used to carry the needed response IOCB states */
+struct lpfc_sli4_rspiocb_info {
+ uint8_t hw_status;
+ uint8_t bfield;
+#define LPFC_XB 0x1
+#define LPFC_PV 0x2
+ uint8_t priority;
+ uint8_t reserved;
+};
+
/* This structure is used to handle IOCB requests / responses */
struct lpfc_iocbq {
/* lpfc_iocbqs are used in double linked lists */
struct list_head list;
struct list_head clist;
uint16_t iotag; /* pre-assigned IO tag */
- uint16_t rsvd1;
+ uint16_t sli4_xritag; /* pre-assigned XRI, (OXID) tag. */
IOCB_t iocb; /* IOCB cmd */
uint8_t retry; /* retry counter for IOCB cmd - if needed */
@@ -65,7 +75,7 @@ struct lpfc_iocbq {
struct lpfc_iocbq *);
void (*iocb_cmpl) (struct lpfc_hba *, struct lpfc_iocbq *,
struct lpfc_iocbq *);
-
+ struct lpfc_sli4_rspiocb_info sli4_info;
};
#define SLI_IOCB_RET_IOCB 1 /* Return IOCB if cmd ring full */
@@ -81,14 +91,18 @@ struct lpfc_iocbq {
typedef struct lpfcMboxq {
/* MBOXQs are used in single linked lists */
struct list_head list; /* ptr to next mailbox command */
- MAILBOX_t mb; /* Mailbox cmd */
- struct lpfc_vport *vport;/* virutal port pointer */
+ union {
+ MAILBOX_t mb; /* Mailbox cmd */
+ struct lpfc_mqe mqe;
+ } u;
+ struct lpfc_vport *vport;/* virtual port pointer */
void *context1; /* caller context information */
void *context2; /* caller context information */
void (*mbox_cmpl) (struct lpfc_hba *, struct lpfcMboxq *);
uint8_t mbox_flag;
-
+ struct lpfc_mcqe mcqe;
+ struct lpfc_mbx_nembed_sge_virt *sge_array;
} LPFC_MBOXQ_t;
#define MBX_POLL 1 /* poll mailbox till command done, then
@@ -234,6 +248,7 @@ struct lpfc_sli {
#define LPFC_PROCESS_LA 0x400 /* Able to process link attention */
#define LPFC_BLOCK_MGMT_IO 0x800 /* Don't allow mgmt mbx or iocb cmds */
#define LPFC_MENLO_MAINT 0x1000 /* need for menl fw download */
+#define LPFC_SLI_ASYNC_MBX_BLK 0x2000 /* Async mailbox is blocked */
struct lpfc_sli_ring ring[LPFC_MAX_RING];
int fcp_ring; /* ring used for FCP initiator commands */
@@ -261,6 +276,8 @@ struct lpfc_sli {
#define LPFC_MBOX_TMO 30 /* Sec tmo for outstanding mbox
command */
+#define LPFC_MBOX_SLI4_CONFIG_TMO 60 /* Sec tmo for outstanding mbox
+ command */
#define LPFC_MBOX_TMO_FLASH_CMD 300 /* Sec tmo for outstanding FLASH write
* or erase cmds. This is especially
* long because of the potential of
diff -upNr a/drivers/scsi/lpfc/lpfc_vport.c b/drivers/scsi/lpfc/lpfc_vport.c
--- a/drivers/scsi/lpfc/lpfc_vport.c 2009-05-19 09:39:28.000000000 -0400
+++ b/drivers/scsi/lpfc/lpfc_vport.c 2009-05-22 13:16:40.000000000 -0400
@@ -32,8 +32,10 @@
#include <scsi/scsi_device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_transport_fc.h>
+#include "lpfc_hw4.h"
#include "lpfc_hw.h"
#include "lpfc_sli.h"
+#include "lpfc_sli4.h"
#include "lpfc_nl.h"
#include "lpfc_disc.h"
#include "lpfc_scsi.h"
@@ -89,6 +91,8 @@ lpfc_alloc_vpi(struct lpfc_hba *phba)
vpi = 0;
else
set_bit(vpi, phba->vpi_bmask);
+ if (phba->sli_rev == LPFC_SLI_REV4)
+ phba->sli4_hba.max_cfg_param.vpi_used++;
spin_unlock_irq(&phba->hbalock);
return vpi;
}
@@ -96,8 +100,12 @@ lpfc_alloc_vpi(struct lpfc_hba *phba)
static void
lpfc_free_vpi(struct lpfc_hba *phba, int vpi)
{
+ if (vpi == 0)
+ return;
spin_lock_irq(&phba->hbalock);
clear_bit(vpi, phba->vpi_bmask);
+ if (phba->sli_rev == LPFC_SLI_REV4)
+ phba->sli4_hba.max_cfg_param.vpi_used--;
spin_unlock_irq(&phba->hbalock);
}
@@ -308,6 +316,21 @@ lpfc_vport_create(struct fc_vport *fc_vp
goto error_out;
}
+ /*
+ * In SLI4, the vpi must be activated before it can be used
+ * by the port.
+ */
+ if (phba->sli_rev == LPFC_SLI_REV4) {
+ rc = lpfc_sli4_init_vpi(phba, vpi);
+ if (rc) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_VPORT,
+ "1838 Failed to INIT_VPI on vpi %d "
+ "status %d\n", vpi, rc);
+ rc = VPORT_NORESOURCES;
+ lpfc_free_vpi(phba, vpi);
+ goto error_out;
+ }
+ }
/* Assign an unused board number */
if ((instance = lpfc_get_instance()) < 0) {
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
