On Thursday February 28, k-tanaka@xxxxxxxxxxxxx wrote:
> This message describes another issue about md RAID10 found by
> testing the 2.6.24 md RAID10 using new scsi fault injection framework.
Thanks for this one too.
The patch looks good (except for some tiny formatting changes).
I'll forward it upstream shortly.
NeilBrown
>
> Abstract:
> When a scsi error results in disabling a disk during RAID10 recovery,
> the resync threads of md RAID10 could stall.
> This case, the raid array has already been broken and it may not matter.
> But I think stall is not preferable. If it occurs, even shutdown or reboot
> will fail because of resource busy.
>
> The deadlock mechanism:
> The r10bio_s structure has a "remaining" member to keep track of BIOs yet to be
> handled when recovering. The "remaining" counter is incremented when building a BIO
> in sync_request() and is decremented when finish a BIO in end_sync_write().
>
> If building a BIO fails for some reasons in sync_request(), the "remaining" should be
> decremented if it has already been incremented. I found a case where this decrement
> is forgotten. This causes a md_do_sync() deadlock because md_do_sync() waits for
> md_done_sync() called by end_sync_write(), but end_sync_write() never calls
> md_done_sync() because of the "remaining" counter mismatch.
>
> For example, this problem would be reproduced in the following case:
>
> Personalities : [raid10]
> md0 : active raid10 sdf1[4] sde1[5](F) sdd1[2] sdc1[1] sdb1[6](F)
> 3919616 blocks 64K chunks 2 near-copies [4/2] [_UU_]
> [>....................] recovery = 2.2% (45376/1959808) finish=0.7min speed=45376K/sec
>
> This case, sdf1 is recovering, sdb1 and sde1 are disabled.
> An additional error with detaching sdd will cause a deadlock.
>
> md0 : active raid10 sdf1[4] sde1[5](F) sdd1[6](F) sdc1[1] sdb1[7](F)
> 3919616 blocks 64K chunks 2 near-copies [4/1] [_U__]
> [=>...................] recovery = 5.0% (99520/1959808) finish=5.9min speed=5237K/sec
>
> 2739 ? S< 0:17 [md0_raid10]
> 28608 ? D< 0:00 [md0_resync]
> 28629 pts/1 Ss 0:00 bash
> 28830 pts/1 R+ 0:00 ps ax
> 31819 ? D< 0:00 [kjournald]
>
> The resync thread keeps working, but actually it is deadlocked.
>
> Patch:
> By this patch, the remaining counter will be decremented if needed.
>
> --- raid10.c.org 2008-01-30 01:09:04.000000000 +0900
> +++ raid10.c 2008-02-26 16:27:22.000000000 +0900
> @@ -1805,6 +1805,9 @@ static sector_t sync_request(mddev_t *md
> if (j == conf->copies) {
> /* Cannot recover, so abort the recovery */
> put_buf(r10_bio);
> + if (rb2) {
> + atomic_dec(&rb2->remaining);
> + }
> r10_bio = rb2;
> if (!test_and_set_bit(MD_RECOVERY_ERR, &mddev->recovery))
> printk(KERN_INFO "raid10: %s: insufficient working devices for recovery.\n",
>
>
> This problem is also detected by using new scsi fault injection framework.
> I have posted a new version to sourceforge with some sample shell script
> using the framework for usability. If you are interested, please take a look at it.
>
>
> --
>
> ---------------------------------------------------------
> Kenichi TANAKA | Open Source Software Platform Development Division
> | Computers Software Operations Unit, NEC Corporation
> | k-tanaka@xxxxxxxxxxxxx
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-raid" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
