On Thu, Feb 28, 2008 at 08:15:25PM -0500, James Bottomley wrote:
> On Thu, 2008-02-28 at 11:16 +0800, Ke Wei wrote:
> > On Thu, Feb 28, 2008 at 12:22 AM, James Bottomley
> > <James.Bottomley@xxxxxxxxxxxxxxxxxxxxx> wrote:
> > > On Wed, 2008-02-27 at 20:50 +0800, Ke Wei wrote:
> > > > 1. Owing to device testing, we need the kernel can show mvsas current
> > > > version in the /proc system.
> > >
> > > I'm afraid proc is really deprecated now. We have /sys for showing
> > > necessary information. For an example of how to use /sys, aacraid does
> > > it the right way (drivers/scsi/aacraid/linit.c). They use this for
> > > exposing a lot of detail about the actual device and its firmware. The
> > > format of sysfs is one entry per file, rather than descriptive text.
> > >
> > > However, for both the parameters you're trying to export, you can get
> > > them an alternative way. The driver version is available from modinfo,
> > > which is usually what your support is looking for:
> > >
> > > jejb@hobholes> modinfo -F version mvsas
> > > 0.5
> > >
> > > And the sas_address is available from the phys. Because it's possible
> > > for a HBA to have a different address per phy, it has to be stored this
> > > way:
> > >
> > > jejb@hobholes> ls /sys/class/sas_host/host0/device/*/sas_phy\:*/sas_address
> > > /sys/class/sas_host/host0/device/phy-0:0/sas_phy:phy-0:0/sas_address
> > > /sys/class/sas_host/host0/device/phy-0:1/sas_phy:phy-0:1/sas_address
> > > /sys/class/sas_host/host0/device/phy-0:2/sas_phy:phy-0:2/sas_address
> > > /sys/class/sas_host/host0/device/phy-0:3/sas_phy:phy-0:3/sas_address
> > > /sys/class/sas_host/host0/device/phy-0:4/sas_phy:phy-0:4/sas_address
> > > /sys/class/sas_host/host0/device/phy-0:5/sas_phy:phy-0:5/sas_address
> > > /sys/class/sas_host/host0/device/phy-0:6/sas_phy:phy-0:6/sas_address
> > > /sys/class/sas_host/host0/device/phy-0:7/sas_phy:phy-0:7/sas_address
> > >
> > > (showing that the sas_address is stored under the sas_phy class in
> > > sysfs). The values for this one (aic94xx) are all the same:
> > >
> > > jejb@hobholes> cat /sys/class/sas_host/host0/device/*/sas_phy\:*/sas_address
> > > 0x50000d100001cae0
> > > 0x50000d100001cae0
> > > 0x50000d100001cae0
> > > 0x50000d100001cae0
> > > 0x50000d100001cae0
> > > 0x50000d100001cae0
> > > 0x50000d100001cae0
> > > 0x50000d100001cae0
> > >
> > Ok, I will tell our testing team how to show version in this way.
>
> Thanks!
>
> > >
> > > > 2. Set the correct SAS address to per port.
> > >
> > > This looks interesting:
> > >
> > > > for (i = 0; i < mvi->chip->n_phy; i++) {
> > > > - /* FIXME: is this the correct dword order? */
> > > > - u32 lo = *((u32 *)&mvi->sas_addr[0]);
> > > > - u32 hi = *((u32 *)&mvi->sas_addr[4]);
> > > > + u32 lo = swab32p((u32 *)&mvi->sas_addr[4]);
> > > > + u32 hi = swab32p((u32 *)&mvi->sas_addr[0]);
> > > >
> > > > mvs_detect_porttype(mvi, i);
> > >
> > > I'm assuming the swab32p is because the mvi->sas_addr array is in wire
> > > (big endian) format, and you need to write it out to the config
> > > registers as two u32 upper and lower words via mvs_write_port_cfg. As
> > > long as that register set is always in pci order (little endian), I
> > > think this will work, but has it been tested on a big endian system,
> > > like PPC?
> >
> > Yes, the mvi->sas_addr array is in wire big endian format. And it
> > will be written to two
> > little-endian 32-bit registers after converting to little endian. So I
> > think this is independent
> > of system architecture.
>
> OK, so in that case, this manner of doing the transformations will fail
> on a Big Endian machine. I think instead of the swab32p, which will
> swap to little endian all the time, you want be32_to_cpu() which will
> swap on a little endian CPU but not on a big endian one.
>
> The register outputs eventually go via writel which likewise includes a
> cpu_to_<architecture endianness> before it actually does the write (So
> on a big endian machine, writel takes big endian in and swaps to output
> in PCI bus format, which is little endian).
>
> James
You are right. I will patch for this issue.
BTW, mvsas driver may perform big endian transfers in a big-endian system in the future.
Thanks.
Signed-off-by: Ke Wei <kewei@xxxxxxxxxxx>
diff --git a/drivers/scsi/mvsas.c b/drivers/scsi/mvsas.c
old mode 100644
new mode 100755
index 3e56178..1f77b6e
--- a/drivers/scsi/mvsas.c
+++ b/drivers/scsi/mvsas.c
@@ -2747,8 +2747,8 @@ static int __devinit mvs_hw_init(struct mvs_info *mvi)
msleep(100);
/* init and reset phys */
for (i = 0; i < mvi->chip->n_phy; i++) {
- u32 lo = swab32p((u32 *)&mvi->sas_addr[4]);
- u32 hi = swab32p((u32 *)&mvi->sas_addr[0]);
+ u32 lo = be32_to_cpu(*(u32 *)&mvi->sas_addr[4]);
+ u32 hi = be32_to_cpu(*(u32 *)&mvi->sas_addr[0]);
mvs_detect_porttype(mvi, i);
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
