On Wed, 2008-01-16 at 16:01 +0200, Boaz Harrosh wrote:
> On Tue, Jan 15 2008 at 19:35 +0200, Boaz Harrosh <bharrosh@xxxxxxxxxxx> wrote:
> > On Tue, Jan 15 2008 at 18:49 +0200, James Bottomley <James.Bottomley@xxxxxxxxxxxxxxxxxxxxx> wrote:
> >> On Tue, 2008-01-15 at 18:09 +0200, Boaz Harrosh wrote:
> >>> On Tue, Jan 15 2008 at 17:52 +0200, James Bottomley <James.Bottomley@xxxxxxxxxxxxxxxxxxxxx> wrote:
> >>>> I thought, now we had this new shiny code to increase the scatterlist
> >>>> table size I'd try it out. It turns out there's a pretty vast block
> >>>> conspiracy that prevents us going over 128 entries in a scatterlist.
> >>>>
> >>>> The first problems are in SCSI: The host parameters sg_tablesize and
> >>>> max_sectors are used to set the queue limits max_hw_segments and
> >>>> max_sectors respectively (the former is the maximum number of entries
> >>>> the HBA can tolerate in a scatterlist for each transaction, the latter
> >>>> is a total transfer cap on the maxiumum number of 512 byte sectors).
> >>>> The default settings, assuming the HBA doesn't vary them are
> >>>> sg_tablesize at SG_ALL (255) and max_sectors at SCSI_DEFAULT_MAX_SECTORS
> >>>> (1024). A quick calculation shows the latter is actually 512k or 128
> >>>> pages (at 4k pages), hence the persistent 128 entry limit.
> >>>>
> >>>> However, raising max_sectors and sg_tablesize together still doesn't
> >>>> help: There's actually an insidious limit sitting in the block layer as
> >>>> well. This is what blk_queue_max_sectors says:
> >>>>
> >>>> void blk_queue_max_sectors(struct request_queue *q, unsigned int
> >>>> max_sectors)
> >>>> {
> >>>> if ((max_sectors << 9) < PAGE_CACHE_SIZE) {
> >>>> max_sectors = 1 << (PAGE_CACHE_SHIFT - 9);
> >>>> printk("%s: set to minimum %d\n", __FUNCTION__, max_sectors);
> >>>> }
> >>>>
> >>>> if (BLK_DEF_MAX_SECTORS > max_sectors)
> >>>> q->max_hw_sectors = q->max_sectors = max_sectors;
> >>>> else {
> >>>> q->max_sectors = BLK_DEF_MAX_SECTORS;
> >>>> q->max_hw_sectors = max_sectors;
> >>>> }
> >>>> }
> >>>>
> >>>> So it imposes a maximum possible setting of BLK_DEF_MAX_SECTORS which is
> >>>> defined in blkdev.h to .... 1024, thus also forcing the queue down to
> >>>> 128 scatterlist entries.
> >>>>
> >>>> Once I raised this limit as well, I was able to transfer over 128
> >>>> scatterlist elements during benchmark test runs of normal I/O (actually
> >>>> kernel compiles seem best, they hit 608 scatterlist entries).
> >>>>
> >>>> So my question, is there any reason not to raise this limit to something
> >>>> large (like 65536) or even eliminate it altogether?
> >>>>
> >>>> James
> >>>>
> >>> I have an old branch here where I've swiped through the scsi drivers just
> >>> to remove the SG_ALL limit. Unfortunately some drivers mean laterally
> >>> 255 when using SG_ALL. So I passed driver by driver and carfully inspected
> >>> the code to change it to something driver specific if they really meant
> >>> 255.
> >>>
> >>> I have used sg_tablesize = ~0; to indicate, I don't care any will do,
> >>> and some driver constant if there is a real limit. Though removing
> >>> SG_ALL at the end.
> >>>
> >>> Should I freshen up this branch and send it.
> >> By all means; however, I think having the defined constant SG_ALL is
> >> useful (even if it is eventually just set to ~0) it means I can support
> >> any scatterlist size. Having the drivers set sg_tablesize correctly
> >> that can't support SG_ALL is pretty vital.
> >>
> >> Thanks,
> >>
> >> James
> > OK will do.
> >
> > I have found the old branch and am looking. I agree with you about the
> > SG_ALL. I will fix it to have a patch per changed driver, with out changing
> > SG_ALL, and then final patch to just change SG_ALL.
> >
> > Boaz
>
>
> James hi
> reinspecting the code, what should I do with drivers that do not support chaining
> do to SW that still do sglist++?
>
> should I set their sg_tablesize to SG_MAX_SINGLE_ALLOC, or hard code to 128, and put
> a FIXME: in the submit message?
>
> or should we fix them first and serialize this effort on top of those fixes.
> (also in light of the other email where you removed the chaining flag)
How many of them are left?
The correct value is clearly SCSI_MAX_SG_SEGMENTS which fortunately
"[PATCH] remove use_sg_chaining" moved into a shared header. Worst
case, just use that and add a fixme comment giving the real value (if
there is one).
James
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
