Since we typically do not maintain changelogs as text files in the Linux kernel, and since the ips changelog has not been updated since 2002, remove it. Signed-off-by: Bart Van Assche <bvanassche@xxxxxxx> --- Documentation/scsi/ChangeLog.ips | 122 ------------------------------- 1 file changed, 122 deletions(-) delete mode 100644 Documentation/scsi/ChangeLog.ips diff --git a/Documentation/scsi/ChangeLog.ips b/Documentation/scsi/ChangeLog.ips deleted file mode 100644 index 5019f5182bf4..000000000000 --- a/Documentation/scsi/ChangeLog.ips +++ /dev/null @@ -1,122 +0,0 @@ -IBM ServeRAID driver Change Log -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - - 5.00.01 - Sarasota ( 5i ) adapters must always be scanned first - - Get rid on IOCTL_NEW_COMMAND code - - Add Extended DCDB Commands for Tape Support in 5I - - 4.90.11 - Don't actually RESET unless it's physically required - - Remove unused compile options - - 4.90.08 - Data Corruption if First Scatter Gather Element is > 64K - - 4.90.08 - Increase Delays in Flashing ( Trombone Only - 4H ) - - 4.90.05 - Use New PCI Architecture to facilitate Hot Plug Development - - 4.90.01 - Add ServeRAID Version Checking - - 4.80.26 - Clean up potential code problems ( Arjan's recommendations ) - - 4.80.21 - Change memcpy() to copy_to_user() in NVRAM Page 5 IOCTL path - - 4.80.20 - Set max_sectors in Scsi_Host structure ( if >= 2.4.7 kernel ) - - 5 second delay needed after resetting an i960 adapter - - 4.80.14 - Take all semaphores off stack - - Clean Up New_IOCTL path - - 4.80.04 - Eliminate calls to strtok() if 2.4.x or greater - - Adjustments to Device Queue Depth - - 4.80.00 - Make ia64 Safe - - 4.72.01 - I/O Mapped Memory release ( so "insmod ips" does not Fail ) - - Don't Issue Internal FFDC Command if there are Active Commands - - Close Window for getting too many IOCTL's active - - 4.72.00 - Allow for a Scatter-Gather Element to exceed MAX_XFER Size - - 4.71.00 - Change all memory allocations to not use GFP_DMA flag - - Code Clean-Up for 2.4.x kernel - - 4.70.15 - Fix Breakup for very large ( non-SG ) requests - - 4.70.13 - Don't release HA Lock in ips_next() until SC taken off queue - - Unregister SCSI device in ips_release() - - Don't Send CDB's if we already know the device is not present - - 4.70.12 - Corrective actions for bad controller ( during initialization ) - - 4.70.09 - Use a Common ( Large Buffer ) for Flashing from the JCRM CD - - Add IPSSEND Flash Support - - Set Sense Data for Unknown SCSI Command - - Use Slot Number from NVRAM Page 5 - - Restore caller's DCDB Structure - - 4.20.14 - Update patch files for kernel 2.4.0-test5 - - 4.20.13 - Fix some failure cases / reset code - - Hook into the reboot_notifier to flush the controller - cache - - 4.20.03 - Rename version to coincide with new release schedules - - Performance fixes - - Fix truncation of /proc files with cat - - Merge in changes through kernel 2.4.0test1ac21 - - 4.10.13 - Fix for dynamic unload and proc file system - - 4.10.00 - Add support for ServeRAID 4M/4L - - 4.00.06 - Fix timeout with initial FFDC command - - 4.00.05 - Remove wish_block from init routine - - Use linux/spinlock.h instead of asm/spinlock.h for kernels - 2.3.18 and later - - Sync with other changes from the 2.3 kernels - - 4.00.04 - Rename structures/constants to be prefixed with IPS_ - - 4.00.03 - Add alternative passthru interface - - Add ability to flash ServeRAID BIOS - - 4.00.02 - Fix problem with PT DCDB with no buffer - - 4.00.01 - Add support for First Failure Data Capture - - 4.00.00 - Add support for ServeRAID 4 - - 3.60.02 - Make DCDB direction based on lookup table. - - Only allow one DCDB command to a SCSI ID at a time. - - 3.60.01 - Remove bogus error check in passthru routine. - - 3.60.00 - Bump max commands to 128 for use with ServeRAID - firmware 3.60. - - Change version to 3.60 to coincide with ServeRAID release - numbering. - - 1.00.00 - Initial Public Release - - Functionally equivalent to 0.99.05 - - 0.99.05 - Fix an oops on certain passthru commands - - 0.99.04 - Fix race condition in the passthru mechanism - -- this required the interface to the utilities to change - - Fix error recovery code - - 0.99.03 - Make interrupt routine handle all completed request on the - adapter not just the first one - - Make sure passthru commands get woken up if we run out of - SCBs - - Send all of the commands on the queue at once rather than - one at a time since the card will support it. - - 0.99.02 - Added some additional debug statements to print out - errors if an error occurs while trying to read/write - to a logical drive (IPS_DEBUG). - - - Fixed read/write errors when the adapter is using an - 8K stripe size. -
