Re: [PATCH v6 06/10] scsi: ufs: ufs-qcom: Set initial PHY gear to max HS gear for HW ver 4 and newer

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 11/30/2023 2:47 PM, Manivannan Sadhasivam wrote:
On Wed, Nov 29, 2023 at 12:28:31AM -0800, Can Guo wrote:
Since HW ver 4, max HS gear can be get from UFS host controller's register,
use the max HS gear as the initial PHY gear instead of UFS_HS_G2, so that
we don't need to update the hard code for newer targets in future.

Signed-off-by: Can Guo <quic_cang@xxxxxxxxxxx>

One comment below. With that addressed,

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>

---
  drivers/ufs/host/ufs-qcom.c | 21 +++++++++++++++------
  1 file changed, 15 insertions(+), 6 deletions(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index aca6199..30f4ca6 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -1060,6 +1060,20 @@ static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
  		hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
  }
+static void ufs_qcom_set_phy_gear(struct ufs_qcom_host *host)
+{
+	struct ufs_host_params *host_params = &host->host_params;
+
+	host->phy_gear = host_params->hs_tx_gear;
+
+	/*
+	 * Power up the PHY using the minimum supported gear (UFS_HS_G2).
+	 * Switching to max gear will be performed during reinit if supported.

As I mentioned in v5, you need to reword this comment to make it clear we are
setting G2 only for platforms < v4. Something like below:

"For controllers whose major version is < 4, power up the PHY using minimum
supported gear (UFS_HS_G2). Switching to max gear will be performed during
reinit if supported. For newer controllers (>= 4), PHY will be powered up using
max supported gear."

Sorry that I missed this one, will add in next version.

Thanks,
Can Guo.


- Mani

+	 */
+	if (host->hw_ver.major < 0x4)
+		host->phy_gear = UFS_HS_G2;
+}
+
  static void ufs_qcom_set_host_params(struct ufs_hba *hba)
  {
  	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
@@ -1296,6 +1310,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)
  	ufs_qcom_set_caps(hba);
  	ufs_qcom_advertise_quirks(hba);
  	ufs_qcom_set_host_params(hba);
+	ufs_qcom_set_phy_gear(host);
err = ufs_qcom_ice_init(host);
  	if (err)
@@ -1313,12 +1328,6 @@ static int ufs_qcom_init(struct ufs_hba *hba)
  		dev_warn(dev, "%s: failed to configure the testbus %d\n",
  				__func__, err);
- /*
-	 * Power up the PHY using the minimum supported gear (UFS_HS_G2).
-	 * Switching to max gear will be performed during reinit if supported.
-	 */
-	host->phy_gear = UFS_HS_G2;
-
  	return 0;
out_variant_clear:
--
2.7.4







[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]

  Powered by Linux