Re: [PATCH v5 04/10] scsi: ufs: ufs-qcom: Limit negotiated gear to selected PHY gear

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 11/28/2023 6:52 PM, Manivannan Sadhasivam wrote:
On Tue, Nov 28, 2023 at 04:05:59PM +0800, Can Guo wrote:
Hi Mani,

On 11/28/2023 1:45 PM, Manivannan Sadhasivam wrote:
On Thu, Nov 23, 2023 at 12:46:24AM -0800, Can Guo wrote:
In the dual init scenario, the initial PHY gear is set to HS-G2, and the
first Power Mode Change (PMC) is meant to find the best matching PHY gear
for the 2nd init. However, for the first PMC, if the negotiated gear (say
HS-G4) is higher than the initial PHY gear, we cannot go ahead let PMC to
the negotiated gear happen, because the programmed UFS PHY settings may not
support the negotiated gear. Fix it by overwriting the negotiated gear with
the PHY gear.


I don't quite understand this patch. If the phy_gear is G2 initially and the
negotiated gear is G4, then as per this change,

phy_gear = G4;
negotiated gear = G2;

Could you please explain how this make sense?

phy_gear was G2 (in the beginning) and just now changed to G4, but the PHY
settings programmed in the beginning can only support no-G4 (not G4).
Without this change, as the negotiated gear is G4, the power mode change is
going to put UFS at HS-G4 mode, but the PHY settings programmed is no-G4.

But we are going to reinit the PHY anyway, isn't it?

We are power mode changing to HS-G4 with no-G4 PHY settings programmed, the power mode change operation, in the 1st init, may immediately cause UIC errors and lead to probe fail. We are not seeing issues as of now, maybe because the amount of HW used for testing is not large enough.

This change is not really related to this specific series, I can remove it in next version.

Thanks,
Can Guo.


This change is to limit the negotiated gear to HS-G2 for the 1st init. In
the 2nd init, as the new PHY gear is G4, G4 PHY settings would be
programmed, it'd be safe to put the UFS at HS-G4 mode.


Why do we need to limit it since we already have the logic in place to set
whatever gear mode applicable for 1st init?

- Mani

Thanks,
Can Guo.

- Mani

Signed-off-by: Can Guo <quic_cang@xxxxxxxxxxx>
---
   drivers/ufs/host/ufs-qcom.c | 7 ++++++-
   1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index cc0eb37..d4edf58 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -920,8 +920,13 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
   		 * because, the PHY gear settings are backwards compatible and we only need to
   		 * change the PHY gear settings while scaling to higher gears.
   		 */
-		if (dev_req_params->gear_tx > host->phy_gear)
+		if (dev_req_params->gear_tx > host->phy_gear) {
+			u32 old_phy_gear = host->phy_gear;
+
   			host->phy_gear = dev_req_params->gear_tx;
+			dev_req_params->gear_tx = old_phy_gear;
+			dev_req_params->gear_rx = old_phy_gear;
+		}
   		/* enable the device ref clock before changing to HS mode */
   		if (!ufshcd_is_hs_mode(&hba->pwr_info) &&
--
2.7.4







[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]

  Powered by Linux