Re: [PATCH v5 03/10] scsi: ufs: ufs-qcom: Setup host power mode during init

[Nitin Rawat <quic_nitirawa@xxxxxxxxxxx>]

On 11/23/2023 2:16 PM, Can Guo wrote:
> Setup host power mode and its limitations during UFS host driver init to
> avoid repetitive work during every power mode change.
>
> Acked-by: Andrew Halaney <ahalaney@xxxxxxxxxx>
> Co-developed-by: Bao D. Nguyen <quic_nguyenb@xxxxxxxxxxx>
> Signed-off-by: Bao D. Nguyen <quic_nguyenb@xxxxxxxxxxx>
> Signed-off-by: Can Guo <quic_cang@xxxxxxxxxxx>
> ---
>   drivers/ufs/host/ufs-qcom.c | 21 ++++++++++++++-------
>   drivers/ufs/host/ufs-qcom.h |  1 +
>   2 files changed, 15 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index cc30ad9..cc0eb37 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -898,7 +898,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
>   				struct ufs_pa_layer_attr *dev_req_params)
>   {
>   	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> -	struct ufs_host_params host_params;
> +	struct ufs_host_params *host_params = &host->host_params;
>   	int ret = 0;
>   
>   	if (!dev_req_params) {
> @@ -908,12 +908,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
>   
>   	switch (status) {
>   	case PRE_CHANGE:
> -		ufshcd_init_host_param(&host_params);
> -
> -		/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
> -		host_params.hs_tx_gear = host_params.hs_rx_gear = ufs_qcom_get_hs_gear(hba);
> -
> -		ret = ufshcd_negotiate_pwr_param(&host_params, dev_max_params, dev_req_params);
> +		ret = ufshcd_negotiate_pwr_param(host_params, dev_max_params, dev_req_params);
>   		if (ret) {
>   			dev_err(hba->dev, "%s: failed to determine capabilities\n",
>   					__func__);
> @@ -1048,6 +1043,17 @@ static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
>   		hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
>   }
>   
> +static void ufs_qcom_set_host_params(struct ufs_hba *hba)
> +{
> +	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> +	struct ufs_host_params *host_params = &host->host_params;
> +
> +	ufshcd_init_host_param(host_params);
> +
> +	/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
> +	host_params->hs_tx_gear = host_params->hs_rx_gear = ufs_qcom_get_hs_gear(hba);
> +}
> +
>   static void ufs_qcom_set_caps(struct ufs_hba *hba)
>   {
>   	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> @@ -1272,6 +1278,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)
>   
>   	ufs_qcom_set_caps(hba);
>   	ufs_qcom_advertise_quirks(hba);
> +	ufs_qcom_set_host_params(hba);
>   
>   	err = ufs_qcom_ice_init(host);
>   	if (err)
> diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
> index 82cd143..11419eb 100644
> --- a/drivers/ufs/host/ufs-qcom.h
> +++ b/drivers/ufs/host/ufs-qcom.h
> @@ -238,6 +238,7 @@ struct ufs_qcom_host {
>   
>   	struct gpio_desc *device_reset;
>   
> +	struct ufs_host_params host_params;
>   	u32 phy_gear;
>   
>   	bool esi_enabled;

Reviewed-by: Nitin Rawat <quic_nitirawa@xxxxxxxxxxx>