Re: [PATCH v2 5/7] scsi: ufs: ufs-qcom: Set initial PHY gear to max HS gear for HW ver 5 and newer

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Nov 06, 2023 at 08:46:11PM -0800, Can Guo wrote:
> From: Can Guo <quic_cang@xxxxxxxxxxx>
> 
> Set the initial PHY gear to max HS gear for hosts with HW ver 5 and newer.
> 

How about,

"For UFSHC >= 5.0, set the initial PHY gear based on the gear value returned by
ufs_qcom_get_hs_gear(). For the rest, use the existing default value of G2."

> This patch is not changing any functionalities or logic but only a
> preparation patch for the next patch in this series.
> 

You are also moving the default phy_gear code to ufs_qcom_set_host_params(). So
it should be mentioned in the commit message.

> Signed-off-by: Can Guo <quic_cang@xxxxxxxxxxx>
> ---
>  drivers/ufs/host/ufs-qcom.c | 14 ++++++++------
>  1 file changed, 8 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 55ee31d..94d34b5 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -1069,6 +1069,14 @@ static void ufs_qcom_set_host_params(struct ufs_hba *hba)
>  
>  	/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
>  	host_params->hs_tx_gear = host_params->hs_rx_gear = ufs_qcom_get_hs_gear(hba);
> +	host->phy_gear = host_params->hs_tx_gear;
> +
> +	/*
> +	 * Power up the PHY using the minimum supported gear (UFS_HS_G2).
> +	 * Switching to max gear will be performed during reinit if supported.
> +	 */

This comment should be moved inside the "if" condition here as done in the next
patch.

- Mani

> +	if (host->hw_ver.major < 0x5)
> +		host->phy_gear = UFS_HS_G2;
>  }
>  
>  static void ufs_qcom_set_caps(struct ufs_hba *hba)
> @@ -1313,12 +1321,6 @@ static int ufs_qcom_init(struct ufs_hba *hba)
>  		dev_warn(dev, "%s: failed to configure the testbus %d\n",
>  				__func__, err);
>  
> -	/*
> -	 * Power up the PHY using the minimum supported gear (UFS_HS_G2).
> -	 * Switching to max gear will be performed during reinit if supported.
> -	 */
> -	host->phy_gear = UFS_HS_G2;
> -
>  	return 0;
>  
>  out_variant_clear:
> -- 
> 2.7.4
> 

-- 
மணிவண்ணன் சதாசிவம்



[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]

  Powered by Linux