On 10/7/23 15:58, David Wronek wrote:
Add the UFS and QMP PHY nodes for the Qualcomm SC7180 SoC.
Signed-off-by: David Wronek <davidwronek@xxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc7180.dtsi | 70 ++++++++++++++++++++++++++++
1 file changed, 70 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 11f353d416b4..9f18be4fd61a 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -1532,6 +1532,76 @@ mmss_noc: interconnect@1740000 {
qcom,bcm-voters = <&apps_bcm_voter>;
};
+ ufs_mem_hc: ufshc@1d84000 {
+ compatible = "qcom,sc7180-ufshc", "qcom,ufshc",
+ "jedec,ufs-2.0";
+ reg = <0 0x01d84000 0 0x3000>,
+ <0 0x01d90000 0 0x8000>;
+ reg-names = "std", "ice";
Recently the ICE was separated into its own node
+ interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&ufs_mem_phy>;
+ phy-names = "ufsphy";
+ lanes-per-direction = <1>;
+ power-domains = <&gcc UFS_PHY_GDSC>;
+ #reset-cells = <1>;
+ resets = <&gcc GCC_UFS_PHY_BCR>;
+ reset-names = "rst";
+
+ iommus = <&apps_smmu 0xa0 0x0>;
+
+ clock-names =
+ "core_clk",
Remove the newline after the =, here and below
+ "bus_aggr_clk",
+ "iface_clk",
+ "core_clk_unipro",
+ "ref_clk",
+ "tx_lane0_sync_clk",
+ "rx_lane0_sync_clk",
+ "ice_core_clk";
+ clocks =
+ <&gcc GCC_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_UFS_PHY_AHB_CLK>,
+ <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
+ freq-table-hz =
+ <50000000 200000000>,
+ <0 0>,
+ <0 0>,
+ <37500000 150000000>,
+ <0 0>,
+ <0 0>,
+ <0 0>,
+ <0 300000000>;
+
+ interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;
Please make the <s align and use QCOM_ICC_TAG_ALWAYS from
include/dt-bindings/interconnect/qcom,icc.h like in sa8775p.dtsi
+ interconnect-names = "ufs-ddr", "cpu-ufs";
+
+ status = "disabled";
+ };
+
+ ufs_mem_phy: phy@1d87000 {
+ compatible = "qcom,sc7180-qmp-ufs-phy";
+ reg = <0 0x01d87000 0 0x1000>;
+
+ clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
+ <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
Please align the <s
Konrad
