- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@xxxxxxxxxxxxx>
---
drivers/scsi/qla1280.c | 369 ++++++++++++++++++++----------------------------
1 files changed, 154 insertions(+), 215 deletions(-)
diff --git a/drivers/scsi/qla1280.c b/drivers/scsi/qla1280.c
index bd805ec..25ba0bd 100644
--- a/drivers/scsi/qla1280.c
+++ b/drivers/scsi/qla1280.c
@@ -1310,14 +1310,7 @@ qla1280_done(struct scsi_qla_host *ha)
}
/* Release memory used for this I/O */
- if (cmd->use_sg) {
- pci_unmap_sg(ha->pdev, cmd->request_buffer,
- cmd->use_sg, cmd->sc_data_direction);
- } else if (cmd->request_bufflen) {
- pci_unmap_single(ha->pdev, sp->saved_dma_handle,
- cmd->request_bufflen,
- cmd->sc_data_direction);
- }
+ scsi_dma_unmap(cmd);
/* Call the mid-level driver interrupt handler */
CMD_HANDLE(sp->cmd) = (unsigned char *)INVALID_HANDLE;
@@ -1406,14 +1399,14 @@ qla1280_return_status(struct response * sts, struct scsi_cmnd *cp)
break;
case CS_DATA_UNDERRUN:
- if ((cp->request_bufflen - residual_length) <
+ if ((scsi_bufflen(cp) - residual_length) <
cp->underflow) {
printk(KERN_WARNING
"scsi: Underflow detected - retrying "
"command.\n");
host_status = DID_ERROR;
} else {
- cp->resid = residual_length;
+ scsi_set_resid(cp, residual_length);
host_status = DID_OK;
}
break;
@@ -2781,27 +2774,23 @@ qla1280_64bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp)
int status = 0;
int cnt;
int req_cnt;
- u16 seg_cnt;
+ int seg_cnt;
u8 dir;
ENTER("qla1280_64bit_start_scsi:");
/* Calculate number of entries and segments required. */
req_cnt = 1;
- if (cmd->use_sg) {
- sg = (struct scatterlist *) cmd->request_buffer;
- seg_cnt = pci_map_sg(ha->pdev, sg, cmd->use_sg,
- cmd->sc_data_direction);
-
+ seg_cnt = scsi_dma_map(cmd);
+ if (seg_cnt > 0) {
if (seg_cnt > 2) {
req_cnt += (seg_cnt - 2) / 5;
if ((seg_cnt - 2) % 5)
req_cnt++;
}
- } else if (cmd->request_bufflen) { /* If data transfer. */
- seg_cnt = 1;
- } else {
- seg_cnt = 0;
+ } else if (seg_cnt < 0) {
+ status = 1;
+ goto out;
}
if ((req_cnt + 2) >= ha->req_q_cnt) {
@@ -2893,120 +2882,95 @@ qla1280_64bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp)
/* Setup packet address segment pointer. */
dword_ptr = (u32 *)&pkt->dseg_0_address;
- if (cmd->use_sg) { /* If scatter gather */
- /* Load command entry data segments. */
- for_each_sg(sg, s, seg_cnt, cnt) {
- if (cnt == 2)
+ /* Load command entry data segments. */
+ for_each_sg(sg, s, seg_cnt, cnt) {
+ if (cnt == 2)
+ break;
+ dma_handle = sg_dma_address(s);
+#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2)
+ if (ha->flags.use_pci_vchannel)
+ sn_pci_set_vchan(ha->pdev,
+ (unsigned long *)&dma_handle,
+ SCSI_BUS_32(cmd));
+#endif
+ *dword_ptr++ =
+ cpu_to_le32(pci_dma_lo32(dma_handle));
+ *dword_ptr++ =
+ cpu_to_le32(pci_dma_hi32(dma_handle));
+ *dword_ptr++ = cpu_to_le32(sg_dma_len(s));
+ dprintk(3, "S/G Segment phys_addr=%x %x, len=0x%x\n",
+ cpu_to_le32(pci_dma_hi32(dma_handle)),
+ cpu_to_le32(pci_dma_lo32(dma_handle)),
+ cpu_to_le32(sg_dma_len(sg_next(s))));
+ remseg--;
+ }
+ dprintk(5, "qla1280_64bit_start_scsi: Scatter/gather "
+ "command packet data - b %i, t %i, l %i \n",
+ SCSI_BUS_32(cmd), SCSI_TCN_32(cmd),
+ SCSI_LUN_32(cmd));
+ qla1280_dump_buffer(5, (char *)pkt,
+ REQUEST_ENTRY_SIZE);
+
+ /*
+ * Build continuation packets.
+ */
+ dprintk(3, "S/G Building Continuation...seg_cnt=0x%x "
+ "remains\n", seg_cnt);
+
+ while (remseg > 0) {
+ /* Update sg start */
+ sg = s;
+ /* Adjust ring index. */
+ ha->req_ring_index++;
+ if (ha->req_ring_index == REQUEST_ENTRY_CNT) {
+ ha->req_ring_index = 0;
+ ha->request_ring_ptr =
+ ha->request_ring;
+ } else
+ ha->request_ring_ptr++;
+
+ pkt = (cmd_a64_entry_t *)ha->request_ring_ptr;
+
+ /* Zero out packet. */
+ memset(pkt, 0, REQUEST_ENTRY_SIZE);
+
+ /* Load packet defaults. */
+ ((struct cont_a64_entry *) pkt)->entry_type =
+ CONTINUE_A64_TYPE;
+ ((struct cont_a64_entry *) pkt)->entry_count = 1;
+ ((struct cont_a64_entry *) pkt)->sys_define =
+ (uint8_t)ha->req_ring_index;
+ /* Setup packet address segment pointer. */
+ dword_ptr =
+ (u32 *)&((struct cont_a64_entry *) pkt)->dseg_0_address;
+
+ /* Load continuation entry data segments. */
+ for_each_sg(sg, s, remseg, cnt) {
+ if (cnt == 5)
break;
dma_handle = sg_dma_address(s);
#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2)
if (ha->flags.use_pci_vchannel)
sn_pci_set_vchan(ha->pdev,
- (unsigned long *)&dma_handle,
+ (unsigned long *)&dma_handle,
SCSI_BUS_32(cmd));
#endif
*dword_ptr++ =
cpu_to_le32(pci_dma_lo32(dma_handle));
*dword_ptr++ =
cpu_to_le32(pci_dma_hi32(dma_handle));
- *dword_ptr++ = cpu_to_le32(sg_dma_len(s));
- dprintk(3, "S/G Segment phys_addr=%x %x, len=0x%x\n",
+ *dword_ptr++ =
+ cpu_to_le32(sg_dma_len(s));
+ dprintk(3, "S/G Segment Cont. phys_addr=%x %x, len=0x%x\n",
cpu_to_le32(pci_dma_hi32(dma_handle)),
cpu_to_le32(pci_dma_lo32(dma_handle)),
- cpu_to_le32(sg_dma_len(sg_next(s))));
+ cpu_to_le32(sg_dma_len(s)));
remseg--;
}
- dprintk(5, "qla1280_64bit_start_scsi: Scatter/gather "
- "command packet data - b %i, t %i, l %i \n",
- SCSI_BUS_32(cmd), SCSI_TCN_32(cmd),
- SCSI_LUN_32(cmd));
- qla1280_dump_buffer(5, (char *)pkt,
- REQUEST_ENTRY_SIZE);
-
- /*
- * Build continuation packets.
- */
- dprintk(3, "S/G Building Continuation...seg_cnt=0x%x "
- "remains\n", seg_cnt);
-
- while (remseg > 0) {
- /* Update sg start */
- sg = s;
- /* Adjust ring index. */
- ha->req_ring_index++;
- if (ha->req_ring_index == REQUEST_ENTRY_CNT) {
- ha->req_ring_index = 0;
- ha->request_ring_ptr =
- ha->request_ring;
- } else
- ha->request_ring_ptr++;
-
- pkt = (cmd_a64_entry_t *)ha->request_ring_ptr;
-
- /* Zero out packet. */
- memset(pkt, 0, REQUEST_ENTRY_SIZE);
-
- /* Load packet defaults. */
- ((struct cont_a64_entry *) pkt)->entry_type =
- CONTINUE_A64_TYPE;
- ((struct cont_a64_entry *) pkt)->entry_count = 1;
- ((struct cont_a64_entry *) pkt)->sys_define =
- (uint8_t)ha->req_ring_index;
- /* Setup packet address segment pointer. */
- dword_ptr =
- (u32 *)&((struct cont_a64_entry *) pkt)->dseg_0_address;
-
- /* Load continuation entry data segments. */
- for_each_sg(sg, s, remseg, cnt) {
- if (cnt == 5)
- break;
- dma_handle = sg_dma_address(s);
-#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2)
- if (ha->flags.use_pci_vchannel)
- sn_pci_set_vchan(ha->pdev,
- (unsigned long *)&dma_handle,
- SCSI_BUS_32(cmd));
-#endif
- *dword_ptr++ =
- cpu_to_le32(pci_dma_lo32(dma_handle));
- *dword_ptr++ =
- cpu_to_le32(pci_dma_hi32(dma_handle));
- *dword_ptr++ =
- cpu_to_le32(sg_dma_len(s));
- dprintk(3, "S/G Segment Cont. phys_addr=%x %x, len=0x%x\n",
- cpu_to_le32(pci_dma_hi32(dma_handle)),
- cpu_to_le32(pci_dma_lo32(dma_handle)),
- cpu_to_le32(sg_dma_len(s)));
- remseg--;
- }
- dprintk(5, "qla1280_64bit_start_scsi: "
- "continuation packet data - b %i, t "
- "%i, l %i \n", SCSI_BUS_32(cmd),
- SCSI_TCN_32(cmd), SCSI_LUN_32(cmd));
- qla1280_dump_buffer(5, (char *)pkt,
- REQUEST_ENTRY_SIZE);
- }
- } else { /* No scatter gather data transfer */
- dma_handle = pci_map_single(ha->pdev,
- cmd->request_buffer,
- cmd->request_bufflen,
- cmd->sc_data_direction);
-
- sp->saved_dma_handle = dma_handle;
-#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2)
- if (ha->flags.use_pci_vchannel)
- sn_pci_set_vchan(ha->pdev,
- (unsigned long *)&dma_handle,
- SCSI_BUS_32(cmd));
-#endif
- *dword_ptr++ = cpu_to_le32(pci_dma_lo32(dma_handle));
- *dword_ptr++ = cpu_to_le32(pci_dma_hi32(dma_handle));
- *dword_ptr = cpu_to_le32(cmd->request_bufflen);
-
- dprintk(5, "qla1280_64bit_start_scsi: No scatter/"
- "gather command packet data - b %i, t %i, "
- "l %i \n", SCSI_BUS_32(cmd), SCSI_TCN_32(cmd),
- SCSI_LUN_32(cmd));
+ dprintk(5, "qla1280_64bit_start_scsi: "
+ "continuation packet data - b %i, t "
+ "%i, l %i \n", SCSI_BUS_32(cmd),
+ SCSI_TCN_32(cmd), SCSI_LUN_32(cmd));
qla1280_dump_buffer(5, (char *)pkt,
REQUEST_ENTRY_SIZE);
}
@@ -3073,7 +3037,7 @@ qla1280_32bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp)
int status = 0;
int cnt;
int req_cnt;
- uint16_t seg_cnt;
+ int seg_cnt;
dma_addr_t dma_handle;
u8 dir;
@@ -3084,17 +3048,8 @@ qla1280_32bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp)
/* Calculate number of entries and segments required. */
req_cnt = 1;
- if (cmd->use_sg) {
- /*
- * We must build an SG list in adapter format, as the kernel's
- * SG list cannot be used directly because of data field size
- * (__alpha__) differences and the kernel SG list uses virtual
- * addresses where we need physical addresses.
- */
- sg = (struct scatterlist *) cmd->request_buffer;
- seg_cnt = pci_map_sg(ha->pdev, sg, cmd->use_sg,
- cmd->sc_data_direction);
-
+ seg_cnt = scsi_dma_map(cmd);
+ if (seg_cnt > 0) {
/*
* if greater than four sg entries then we need to allocate
* continuation entries
@@ -3106,14 +3061,9 @@ qla1280_32bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp)
}
dprintk(3, "S/G Transfer cmd=%p seg_cnt=0x%x, req_cnt=%x\n",
cmd, seg_cnt, req_cnt);
- } else if (cmd->request_bufflen) { /* If data transfer. */
- dprintk(3, "No S/G transfer t=%x cmd=%p len=%x CDB=%x\n",
- SCSI_TCN_32(cmd), cmd, cmd->request_bufflen,
- cmd->cmnd[0]);
- seg_cnt = 1;
- } else {
- /* dprintk(1, "No data transfer \n"); */
- seg_cnt = 0;
+ } else if (seg_cnt < 0) {
+ status = 1;
+ goto out;
}
if ((req_cnt + 2) >= ha->req_q_cnt) {
@@ -3198,84 +3148,73 @@ qla1280_32bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp)
/* Setup packet address segment pointer. */
dword_ptr = &pkt->dseg_0_address;
- if (cmd->use_sg) { /* If scatter gather */
- dprintk(3, "Building S/G data segments..\n");
- qla1280_dump_buffer(1, (char *)sg, 4 * 16);
+ dprintk(3, "Building S/G data segments..\n");
+ qla1280_dump_buffer(1, (char *)scsi_sglist(cmd), 4 * 16);
- /* Load command entry data segments. */
- for_each_sg(sg, s, seg_cnt, cnt) {
- if (cnt == 4)
- break;
+ /* Load command entry data segments. */
+ for_each_sg(sg, s, seg_cnt, cnt) {
+ if (cnt == 4)
+ break;
+ *dword_ptr++ =
+ cpu_to_le32(pci_dma_lo32(sg_dma_address(s)));
+ *dword_ptr++ = cpu_to_le32(sg_dma_len(s));
+ dprintk(3, "S/G Segment phys_addr=0x%lx, len=0x%x\n",
+ (pci_dma_lo32(sg_dma_address(s))),
+ (sg_dma_len(s)));
+ remseg--;
+ }
+ /*
+ * Build continuation packets.
+ */
+ dprintk(3, "S/G Building Continuation"
+ "...seg_cnt=0x%x remains\n", seg_cnt);
+ while (remseg > 0) {
+ /* Continue from end point */
+ sg = s;
+ /* Adjust ring index. */
+ ha->req_ring_index++;
+ if (ha->req_ring_index == REQUEST_ENTRY_CNT) {
+ ha->req_ring_index = 0;
+ ha->request_ring_ptr =
+ ha->request_ring;
+ } else
+ ha->request_ring_ptr++;
+
+ pkt = (struct cmd_entry *)ha->request_ring_ptr;
+
+ /* Zero out packet. */
+ memset(pkt, 0, REQUEST_ENTRY_SIZE);
+
+ /* Load packet defaults. */
+ ((struct cont_entry *) pkt)->
+ entry_type = CONTINUE_TYPE;
+ ((struct cont_entry *) pkt)->entry_count = 1;
+
+ ((struct cont_entry *) pkt)->sys_define =
+ (uint8_t) ha->req_ring_index;
+
+ /* Setup packet address segment pointer. */
+ dword_ptr =
+ &((struct cont_entry *) pkt)->dseg_0_address;
+
+ /* Load continuation entry data segments. */
+ for_each_sg(sg, s, remseg, cnt) {
*dword_ptr++ =
cpu_to_le32(pci_dma_lo32(sg_dma_address(s)));
- *dword_ptr++ = cpu_to_le32(sg_dma_len(s));
- dprintk(3, "S/G Segment phys_addr=0x%lx, len=0x%x\n",
- (pci_dma_lo32(sg_dma_address(s))),
- (sg_dma_len(s)));
- remseg--;
- }
- /*
- * Build continuation packets.
- */
- dprintk(3, "S/G Building Continuation"
- "...seg_cnt=0x%x remains\n", seg_cnt);
- while (remseg > 0) {
- /* Continue from end point */
- sg = s;
- /* Adjust ring index. */
- ha->req_ring_index++;
- if (ha->req_ring_index == REQUEST_ENTRY_CNT) {
- ha->req_ring_index = 0;
- ha->request_ring_ptr =
- ha->request_ring;
- } else
- ha->request_ring_ptr++;
-
- pkt = (struct cmd_entry *)ha->request_ring_ptr;
-
- /* Zero out packet. */
- memset(pkt, 0, REQUEST_ENTRY_SIZE);
-
- /* Load packet defaults. */
- ((struct cont_entry *) pkt)->
- entry_type = CONTINUE_TYPE;
- ((struct cont_entry *) pkt)->entry_count = 1;
-
- ((struct cont_entry *) pkt)->sys_define =
- (uint8_t) ha->req_ring_index;
-
- /* Setup packet address segment pointer. */
- dword_ptr =
- &((struct cont_entry *) pkt)->dseg_0_address;
-
- /* Load continuation entry data segments. */
- for_each_sg(sg, s, remseg, cnt) {
- *dword_ptr++ =
- cpu_to_le32(pci_dma_lo32(sg_dma_address(s)));
- *dword_ptr++ =
- cpu_to_le32(sg_dma_len(s));
- dprintk(1,
- "S/G Segment Cont. phys_addr=0x%x, "
- "len=0x%x\n",
- cpu_to_le32(pci_dma_lo32(sg_dma_address(s))),
- cpu_to_le32(sg_dma_len(s)));
- }
- dprintk(5, "qla1280_32bit_start_scsi: "
- "continuation packet data - "
- "scsi(%i:%i:%i)\n", SCSI_BUS_32(cmd),
- SCSI_TCN_32(cmd), SCSI_LUN_32(cmd));
- qla1280_dump_buffer(5, (char *)pkt,
- REQUEST_ENTRY_SIZE);
+ *dword_ptr++ =
+ cpu_to_le32(sg_dma_len(s));
+ dprintk(1,
+ "S/G Segment Cont. phys_addr=0x%x, "
+ "len=0x%x\n",
+ cpu_to_le32(pci_dma_lo32(sg_dma_address(s))),
+ cpu_to_le32(sg_dma_len(s)));
}
- } else { /* No S/G data transfer */
- dma_handle = pci_map_single(ha->pdev,
- cmd->request_buffer,
- cmd->request_bufflen,
- cmd->sc_data_direction);
- sp->saved_dma_handle = dma_handle;
-
- *dword_ptr++ = cpu_to_le32(pci_dma_lo32(dma_handle));
- *dword_ptr = cpu_to_le32(cmd->request_bufflen);
+ dprintk(5, "qla1280_32bit_start_scsi: "
+ "continuation packet data - "
+ "scsi(%i:%i:%i)\n", SCSI_BUS_32(cmd),
+ SCSI_TCN_32(cmd), SCSI_LUN_32(cmd));
+ qla1280_dump_buffer(5, (char *)pkt,
+ REQUEST_ENTRY_SIZE);
}
} else { /* No data transfer at all */
dprintk(5, "qla1280_32bit_start_scsi: No data, command "
@@ -4083,9 +4022,9 @@ __qla1280_print_scsi_cmd(struct scsi_cmnd *cmd)
for (i = 0; i < cmd->cmd_len; i++) {
printk("0x%02x ", cmd->cmnd[i]);
}
- printk(" seg_cnt =%d\n", cmd->use_sg);
+ printk(" seg_cnt =%d\n", scsi_sg_count(cmd));
printk(" request buffer=0x%p, request buffer len=0x%x\n",
- cmd->request_buffer, cmd->request_bufflen);
+ scsi_sglist(cmd), scsi_bufflen(cmd));
/* if (cmd->use_sg)
{
sg = (struct scatterlist *) cmd->request_buffer;
--
1.5.2.4
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
