This has scsi_probe_lun ask scsi-ml to retry UAs instead of driving them
itself.
There is one behavior change with this patch. We used to get a total of
3 retries for both UAs we were checking for. We now get 3 retries for
each.
Signed-off-by: Mike Christie <michael.christie@xxxxxxxxxx>
Reviewed-by: Christoph Hellwig <hch@xxxxxx>
---
drivers/scsi/scsi_scan.c | 42 +++++++++++++++++++++++-----------------
1 file changed, 24 insertions(+), 18 deletions(-)
diff --git a/drivers/scsi/scsi_scan.c b/drivers/scsi/scsi_scan.c
index aa13feb17c62..519755952254 100644
--- a/drivers/scsi/scsi_scan.c
+++ b/drivers/scsi/scsi_scan.c
@@ -647,10 +647,29 @@ static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result,
int first_inquiry_len, try_inquiry_len, next_inquiry_len;
int response_len = 0;
int pass, count, result, resid;
- struct scsi_sense_hdr sshdr;
+ /*
+ * not-ready to ready transition [asc/ascq=0x28/0x0] or power-on,
+ * reset [asc/ascq=0x29/0x0], continue. INQUIRY should not yield
+ * UNIT_ATTENTION but many buggy devices do so anyway.
+ */
+ struct scsi_failure failures[] = {
+ {
+ .sense = UNIT_ATTENTION,
+ .asc = 0x28,
+ .allowed = 3,
+ .result = SAM_STAT_CHECK_CONDITION,
+ },
+ {
+ .sense = UNIT_ATTENTION,
+ .asc = 0x29,
+ .allowed = 3,
+ .result = SAM_STAT_CHECK_CONDITION,
+ },
+ {},
+ };
const struct scsi_exec_args exec_args = {
- .sshdr = &sshdr,
.resid = &resid,
+ .failures = failures,
};
*bflags = 0;
@@ -668,6 +687,8 @@ static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result,
pass, try_inquiry_len));
/* Each pass gets up to three chances to ignore Unit Attention */
+ scsi_reset_failures(failures);
+
for (count = 0; count < 3; ++count) {
memset(scsi_cmd, 0, 6);
scsi_cmd[0] = INQUIRY;
@@ -684,22 +705,7 @@ static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result,
"scsi scan: INQUIRY %s with code 0x%x\n",
result ? "failed" : "successful", result));
- if (result > 0) {
- /*
- * not-ready to ready transition [asc/ascq=0x28/0x0]
- * or power-on, reset [asc/ascq=0x29/0x0], continue.
- * INQUIRY should not yield UNIT_ATTENTION
- * but many buggy devices do so anyway.
- */
- if (scsi_status_is_check_condition(result) &&
- scsi_sense_valid(&sshdr)) {
- if ((sshdr.sense_key == UNIT_ATTENTION) &&
- ((sshdr.asc == 0x28) ||
- (sshdr.asc == 0x29)) &&
- (sshdr.ascq == 0))
- continue;
- }
- } else if (result == 0) {
+ if (result == 0) {
/*
* if nothing was transferred, we try
* again. It's a workaround for some USB
--
2.34.1
