Re: [PATCH v2 09/13] scsi: target: iscsit: Fix isert disconnect handling during login

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 1/13/23 08:08, Dmitry Bogdanov wrote:
> On Wed, Jan 11, 2023 at 09:08:28PM -0600, Mike Christie wrote:
>>
>> If we get a disconnect event while logging in we can end up in a state
>> where will never be able to relogin. This happens when:
>>
>> 1. login thread has put us into TARG_CONN_STATE_IN_LOGIN
>> 2. isert then does
>>
>> isert_disconnected_handler -> iscsit_cause_connection_reinstatement
>>
>> which sets the conn connection_reinstatement flag. Nothing else happens
>> because we are only in IN_LOGIN. The tx/rx threads are not running yet
>> so we can't start recovery from those contexts at this time.
>>
>> 3. The login thread finishes processing the login pdu and thinks login is
>> done. It sets us into TARG_CONN_STATE_LOGGED_IN/TARG_SESS_STATE_LOGGED_IN.
>> This starts the rx/tx threads.
>>
>> 4. The initiator thought it disconnected the connection at 2, and has
>> since sent a new connect which is now handled. This leads us to eventually
>> run:
>>
>> iscsi_check_for_session_reinstatement-> iscsit_stop_session ->
>> iscsit_cause_connection_reinstatement
>>
>> iscsit_stop_session sees the old conn and does
>> iscsit_cause_connection_reinstatement which sees connection_reinstatement
>> is set so it just returns instead of trying to kill the tx/rx threads
>> which would have caused recovery to start.
>>
>> 5. iscsit_stop_session then waits on session_wait_comp which will never
>> happen since we didn't kill the tx/rx threads.
>>
>> This has the iscsit login code check if a fabric driver ran
>> iscsit_cause_connection_reinstatement during the login process similar
>> to how we check for the sk state for tcp based iscsit. This will prevent
>> us from getting into 3 and creating a ghost session.
>>
>> Signed-off-by: Mike Christie <michael.christie@xxxxxxxxxx>
>> ---
>>  drivers/target/iscsi/iscsi_target_nego.c | 10 ++++++++++
>>  1 file changed, 10 insertions(+)
>>
>> diff --git a/drivers/target/iscsi/iscsi_target_nego.c b/drivers/target/iscsi/iscsi_target_nego.c
>> index ff49c8f3fe24..2dd81752d4c9 100644
>> --- a/drivers/target/iscsi/iscsi_target_nego.c
>> +++ b/drivers/target/iscsi/iscsi_target_nego.c
>> @@ -350,6 +350,16 @@ static int iscsi_target_do_tx_login_io(struct iscsit_conn *conn, struct iscsi_lo
>>                                             ISCSI_LOGIN_STATUS_NO_RESOURCES);
>>                         return -1;
>>                 }
>> +
>> +               /*
>> +                * isert doesn't know the iscsit state and uses
>> +                * iscsit_cause_connection_reinstatement as a generic error
>> +                * notification system. It may call it before we are in FFP.
>> +                * Handle this now in case it signaled a failure before the
>> +                * rx/tx threads were up and could start recovery.
>> +                */
>> +               if (atomic_read(&conn->connection_reinstatement))
>> +                       goto err;
> 
> Why only for login->login_complete case? In other case the session will
> not hang? Will it be droppped on login timeout or something else?

It will not hang. If you hit an error with isert before we think we can go into
FFP then the login timeout currently cleans up the conn and session.

> 
> May be the root cause is point 2 itself - calling iscsit_cause_connection_reinstatement
> in not ISER_CONN_FULL_FEATURE state where there are no TX_RX threads?
> I mean that was a misuse of iscsit_cause_connection_reinstatement?

Let me drop this patch for now. After writing the response above about normally it just
times out, and thinking about your question here I think to really fix this we want to
fully integrate isert login into iscsit.

The root problem is that isert login is not integrated into iscsit, so there is really
no error handling. iscsit_cause_connection_reinstatement was supposed to do it, but it
doesn't do anything.

So we need to separate the LOGIN_FLAGS_CLOSED tests and setting from the iscsi_target_sk*
code. Add a helper to set that bit and do some state checks, and make the checks generic
in the login code (not tied to having a socket). Convert iscsit and isert to use the new
helper. Then handle the LOGIN_FLAGS_READ_ACTIVE/LOGIN_FLAGS_WRITE_ACTIVE and login_work
stuff. Then review cxgb?

I'll do that later after fixing the command cleanup stuff in this patchsdet and the
other patchsets I have outstanding.



[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]

  Powered by Linux