On Tue, 1 Feb 2022 15:47:47 -0600, Don Brace wrote: > These patches are based on Martin Petersen's 5.18/scsi-queue tree > https://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi.git > 5.18/scsi-queue > > This set of changes consist of: > * Correcting a stack trace when the driver is unloaded. The driver was > holding a spin lock when calling scsi_remove_device. > * Adding in new PCI device IDs and aligning the device order with our > out-of-box driver. No functional changes. > * Allow NCQ to be enabled for SATA disks. The controller firmware has > to have support for this feature. > * Enhance reboot performance by now issuing disk spin-downs during > reboots. This eliminates spin-up time required doing the boot up. > * Speed up multipath failover detection by returning DID_NO_CONNECT > when the controller returns a path failure. Previously, the driver was > waiting on an internal re-scan to detect the path failure. > * Change function name pqi_is_io_high_priority() to > pqi_is_io_high_priority() for better readability. Remove some white > spaces from the same function. > * Correct the structure used for AIO command submission. The structure > used was pqi_raid_path_request, but needs to be pqi_aio_path_request. > Both structure are the same size and have the same member offsets, > so no issues were reported. > * A PQI_HZ MACRO was introduced some time ago to resolve some timing > issues. This definition is not needed. Switch back to using HZ. > * For certain controllers, there was a request to avoid a drive > spin-down for suspend (S3) state transitions. > * For small drive expansions, the driver was not detecting the new > size changes. We added a rescan whenever the driver receives an > event from the controller. > * In some rare cases, the controller can be locked up when a kdump > is requested. When this occurs, the kdump is failed. This helps > in debugging the cause of the lockup. > * For RAID 10 disks, only one set of disks were used for read > operations. Now we spread out I/O to all volumes. This resolves > some inconsistent performance issues. > * Export SAS addresses for all disks instead of only SAS disks. > * Correct NUMA node association during pci_probe. A small typo > was causing a different NUMA node to be set. > * Not all structures were checked with BUILD_BUG_ON. > * Correct some rare Hibernate/Suspend issues. Newer controllers > may boot up with different timings. > * Correct WWID output for lsscsi -t. The wrong part of the 16-byte WWID > was used for the SAS address field. > * Bump the driver version to 2.1.14-035 > > [...] Applied to 5.18/scsi-queue, thanks! [01/18] smartpqi: fix rmmod stack trace https://git.kernel.org/mkp/scsi/c/c4ff687d25c0 [02/18] smartpqi: add PCI IDs https://git.kernel.org/mkp/scsi/c/c57ee4ccb358 [03/18] smartpqi: enable SATA NCQ priority in sysfs https://git.kernel.org/mkp/scsi/c/2a47834d9452 [04/18] smartpqi: eliminate drive spin down on warm boot https://git.kernel.org/mkp/scsi/c/70ba20be4bb1 [05/18] smartpqi: propagate path failures to SML quickly https://git.kernel.org/mkp/scsi/c/94a68c814328 [06/18] smartpqi: fix a name typo and cleanup code https://git.kernel.org/mkp/scsi/c/b4dc06a9070e [07/18] smartpqi: fix a typo in func pqi_aio_submit_io https://git.kernel.org/mkp/scsi/c/9e98e60bfca3 [08/18] smartpqi: resolve delay issue with PQI_HZ value https://git.kernel.org/mkp/scsi/c/42dc0426fbbb [09/18] smartpqi: avoid drive spin-down during suspend https://git.kernel.org/mkp/scsi/c/b73357a1fd39 [10/18] smartpqi: update volume size after expansion https://git.kernel.org/mkp/scsi/c/27655e9db479 [11/18] smartpqi: fix kdump issue when ctrl is locked up https://git.kernel.org/mkp/scsi/c/3ada501d602a [12/18] smartpqi: speed up RAID 10 sequential reads https://git.kernel.org/mkp/scsi/c/5d8fbce04d36 [13/18] smartpqi: expose SAS address for SATA drives https://git.kernel.org/mkp/scsi/c/00598b056aa6 [14/18] smartpqi: fix NUMA node not updated during init https://git.kernel.org/mkp/scsi/c/c52efc923856 [15/18] smartpqi: fix BUILD_BUG_ON() statements https://git.kernel.org/mkp/scsi/c/5e6935864d81 [16/18] smartpqi: fix hibernate and suspend https://git.kernel.org/mkp/scsi/c/c66e078ad89e [17/18] smartpqi: fix lsscsi-t SAS addresses https://git.kernel.org/mkp/scsi/c/291c2e0071ef [18/18] smartpqi: update version to 2.1.14-035 https://git.kernel.org/mkp/scsi/c/62ed6622aaf0 -- Martin K. Petersen Oracle Linux Engineering
