From: John Garry <john.garry@xxxxxxxxxx> [ Upstream commit 62afb379a0fee7e9c2f9f68e1abeb85ceddf51b9 ] According to the comment in check_fw_ready() we should not check the IOP1_READY field in register SCRATCH_PAD_1 for 8008 or 8009 controllers. However we check this very field in process_oq() for processing the highest index interrupt vector. The highest interrupt vector is checked as the FW is programmed to signal fatal errors through this irq. Change that function to not check IOP1_READY for those mentioned controllers, but do check ILA_READY in both cases. The reason I assume that this was not hit earlier was because we always allocated 64 MSI(X), and just did not pass the vector index check in process_oq(), i.e. the handler never ran for vector index 63. Link: https://lore.kernel.org/r/1642508105-95432-1-git-send-email-john.garry@xxxxxxxxxx Tested-by: Damien Le Moal <damien.lemoal@xxxxxxxxxxxxxxxxxx> Reviewed-by: Damien Le Moal <damien.lemoal@xxxxxxxxxxxxxxxxxx> Signed-off-by: John Garry <john.garry@xxxxxxxxxx> Signed-off-by: Martin K. Petersen <martin.petersen@xxxxxxxxxx> Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx> --- drivers/scsi/pm8001/pm80xx_hwi.c | 16 ++++++++++++++-- drivers/scsi/pm8001/pm80xx_hwi.h | 6 +++++- 2 files changed, 19 insertions(+), 3 deletions(-) diff --git a/drivers/scsi/pm8001/pm80xx_hwi.c b/drivers/scsi/pm8001/pm80xx_hwi.c index 2101fc5761c3c..4c5b945bf3187 100644 --- a/drivers/scsi/pm8001/pm80xx_hwi.c +++ b/drivers/scsi/pm8001/pm80xx_hwi.c @@ -4161,10 +4161,22 @@ static int process_oq(struct pm8001_hba_info *pm8001_ha, u8 vec) u32 ret = MPI_IO_STATUS_FAIL; u32 regval; + /* + * Fatal errors are programmed to be signalled in irq vector + * pm8001_ha->max_q_num - 1 through pm8001_ha->main_cfg_tbl.pm80xx_tbl. + * fatal_err_interrupt + */ if (vec == (pm8001_ha->max_q_num - 1)) { + u32 mipsall_ready; + + if (pm8001_ha->chip_id == chip_8008 || + pm8001_ha->chip_id == chip_8009) + mipsall_ready = SCRATCH_PAD_MIPSALL_READY_8PORT; + else + mipsall_ready = SCRATCH_PAD_MIPSALL_READY_16PORT; + regval = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1); - if ((regval & SCRATCH_PAD_MIPSALL_READY) != - SCRATCH_PAD_MIPSALL_READY) { + if ((regval & mipsall_ready) != mipsall_ready) { pm8001_ha->controller_fatal_error = true; pm8001_dbg(pm8001_ha, FAIL, "Firmware Fatal error! Regval:0x%x\n", diff --git a/drivers/scsi/pm8001/pm80xx_hwi.h b/drivers/scsi/pm8001/pm80xx_hwi.h index c7e5d93bea924..c41ed039c92ac 100644 --- a/drivers/scsi/pm8001/pm80xx_hwi.h +++ b/drivers/scsi/pm8001/pm80xx_hwi.h @@ -1405,8 +1405,12 @@ typedef struct SASProtocolTimerConfig SASProtocolTimerConfig_t; #define SCRATCH_PAD_BOOT_LOAD_SUCCESS 0x0 #define SCRATCH_PAD_IOP0_READY 0xC00 #define SCRATCH_PAD_IOP1_READY 0x3000 -#define SCRATCH_PAD_MIPSALL_READY (SCRATCH_PAD_IOP1_READY | \ +#define SCRATCH_PAD_MIPSALL_READY_16PORT (SCRATCH_PAD_IOP1_READY | \ SCRATCH_PAD_IOP0_READY | \ + SCRATCH_PAD_ILA_READY | \ + SCRATCH_PAD_RAAE_READY) +#define SCRATCH_PAD_MIPSALL_READY_8PORT (SCRATCH_PAD_IOP0_READY | \ + SCRATCH_PAD_ILA_READY | \ SCRATCH_PAD_RAAE_READY) /* boot loader state */ -- 2.34.1
