Implement the ->restore() PM operation and set the link to off, which
will force a full reset and restore. This ensures that Host Performance
Booster is reset after suspend-to-disk.
The Host Performance Booster feature caches logical-to-physical mapping
information in the host memory. After suspend-to-disk, such information
is not valid, so a full reset and restore is needed.
A full reset and restore is done if the SPM level is 5 or 6, but not for
other SPM levels, so this change fixes those cases.
A full reset and restore also restores base address registers, so that
code is removed.
Signed-off-by: Adrian Hunter <adrian.hunter@xxxxxxxxx>
---
drivers/scsi/ufs/ufshcd-pci.c | 31 ++++++++++++++++---------------
1 file changed, 16 insertions(+), 15 deletions(-)
diff --git a/drivers/scsi/ufs/ufshcd-pci.c b/drivers/scsi/ufs/ufshcd-pci.c
index 149c1aa09103..d65e6cd7a28d 100644
--- a/drivers/scsi/ufs/ufshcd-pci.c
+++ b/drivers/scsi/ufs/ufshcd-pci.c
@@ -370,20 +370,6 @@ static void ufs_intel_common_exit(struct ufs_hba *hba)
static int ufs_intel_resume(struct ufs_hba *hba, enum ufs_pm_op op)
{
- /*
- * To support S4 (suspend-to-disk) with spm_lvl other than 5, the base
- * address registers must be restored because the restore kernel can
- * have used different addresses.
- */
- ufshcd_writel(hba, lower_32_bits(hba->utrdl_dma_addr),
- REG_UTP_TRANSFER_REQ_LIST_BASE_L);
- ufshcd_writel(hba, upper_32_bits(hba->utrdl_dma_addr),
- REG_UTP_TRANSFER_REQ_LIST_BASE_H);
- ufshcd_writel(hba, lower_32_bits(hba->utmrdl_dma_addr),
- REG_UTP_TASK_REQ_LIST_BASE_L);
- ufshcd_writel(hba, upper_32_bits(hba->utmrdl_dma_addr),
- REG_UTP_TASK_REQ_LIST_BASE_H);
-
if (ufshcd_is_link_hibern8(hba)) {
int ret = ufshcd_uic_hibern8_exit(hba);
@@ -463,6 +449,16 @@ static struct ufs_hba_variant_ops ufs_intel_lkf_hba_vops = {
.device_reset = ufs_intel_device_reset,
};
+static int ufshcd_pci_restore(struct device *dev)
+{
+ struct ufs_hba *hba = dev_get_drvdata(dev);
+
+ /* Force a full reset and restore */
+ ufshcd_set_link_off(hba);
+
+ return ufshcd_system_resume(dev);
+}
+
/**
* ufshcd_pci_shutdown - main function to put the controller in reset state
* @pdev: pointer to PCI device handle
@@ -546,9 +542,14 @@ ufshcd_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
}
static const struct dev_pm_ops ufshcd_pci_pm_ops = {
- SET_SYSTEM_SLEEP_PM_OPS(ufshcd_system_suspend, ufshcd_system_resume)
SET_RUNTIME_PM_OPS(ufshcd_runtime_suspend, ufshcd_runtime_resume, NULL)
#ifdef CONFIG_PM_SLEEP
+ .suspend = ufshcd_system_suspend,
+ .resume = ufshcd_system_resume,
+ .freeze = ufshcd_system_suspend,
+ .thaw = ufshcd_system_resume,
+ .poweroff = ufshcd_system_suspend,
+ .restore = ufshcd_pci_restore,
.prepare = ufshcd_suspend_prepare,
.complete = ufshcd_resume_complete,
#endif
--
2.25.1
