From: Christoph Hellwig <hch@xxxxxx> Sent: Thursday, September 2, 2021 1:00 AM > > On Tue, Aug 31, 2021 at 05:16:19PM +0000, Michael Kelley wrote: > > As a quick overview, I think there are four places where the > > shared_gpa_boundary must be applied to adjust the guest physical > > address that is used. Each requires mapping a corresponding > > virtual address range. Here are the four places: > > > > 1) The so-called "monitor pages" that are a core communication > > mechanism between the guest and Hyper-V. These are two single > > pages, and the mapping is handled by calling memremap() for > > each of the two pages. See Patch 7 of Tianyu's series. > > Ah, interesting. > > > 3) The network driver send and receive buffers. vmap_phys_range() > > should work here. > > Actually it won't. The problem with these buffers is that they are > physically non-contiguous allocations. Indeed you are right. These buffers are allocated with vzalloc(). > We really have two sensible options: > > 1) use vmap_pfn as in the current series. But in that case I think > we should get rid of the other mapping created by vmalloc. I > though a bit about finding a way to apply the offset in vmalloc > itself, but I think it would be too invasive to the normal fast > path. So the other sub-option would be to allocate the pages > manually (maybe even using high order allocations to reduce TLB > pressure) and then remap them What's the benefit of getting rid of the other mapping created by vmalloc if it isn't referenced? Just page table space? The default sizes are a 16 Meg receive buffer and a 1 Meg send buffer for each VMbus channel used by netvsc, and usually the max number of channels is 8. So there's 128 Meg of virtual space to be saved on the receive buffers, which could be worth it. Allocating the pages manually is also an option, but we have to be careful about high order allocations. While typically these buffers are allocated during system boot, these synthetic NICs can be hot added and removed while the VM is running. The channel count can also be changed while the VM is running. So multiple 16 Meg receive buffer allocations may need to be done after the system has been running a long time. > 2) do away with the contiguous kernel mapping entirely. This means > the simple memcpy calls become loops over kmap_local_pfn. As > I just found out for the send side that would be pretty easy, > but the receive side would be more work. We'd also need to check > the performance implications. Doing away with the contiguous kernel mapping entirely seems like it would result in fairly messy code to access the buffer. What's the benefit of doing away with the mapping? I'm not an expert on the netvsc driver, but decoding the incoming packets is already fraught with complexities because of the nature of the protocol with Hyper-V. The contiguous kernel mapping at least keeps the basics sane. > > > 4) The swiotlb memory used for bounce buffers. vmap_phys_range() > > should work here as well. > > Or memremap if it works for 1. > > > Case #2 above does unusual mapping. The ring buffer consists of a ring > > buffer header page, followed by one or more pages that are the actual > > ring buffer. The pages making up the actual ring buffer are mapped > > twice in succession. For example, if the ring buffer has 4 pages > > (one header page and three ring buffer pages), the contiguous > > virtual mapping must cover these seven pages: 0, 1, 2, 3, 1, 2, 3. > > The duplicate contiguous mapping allows the code that is reading > > or writing the actual ring buffer to not be concerned about wrap-around > > because writing off the end of the ring buffer is automatically > > wrapped-around by the mapping. The amount of data read or > > written in one batch never exceeds the size of the ring buffer, and > > after a batch is read or written, the read or write indices are adjusted > > to put them back into the range of the first mapping of the actual > > ring buffer pages. So there's method to the madness, and the > > technique works pretty well. But this kind of mapping is not > > amenable to using vmap_phys_range(). > > Hmm. Can you point me to where this is mapped? Especially for the > classic non-isolated case where no vmap/vmalloc mapping is involved > at all? The existing code is in hv_ringbuffer_init() in drivers/hv/ring_buffer.c. The code hasn't changed in a while, so any recent upstream code tree is valid to look at. The memory pages are typically allocated in vmbus_alloc_ring() in drivers/hv/channel.c. Michael
