As part of the cmf framework, the firmware maintains a table with
congestion related state information, specifically whether enabled and
if enabled, whether monitoring or actively managing congestion.
Add definition of the table and add support to read the table from the
adapter and determine if it is enabled. In support of this, the
READ_OBJECT mailbox command definition is added to the driver.
Co-developed-by: Justin Tee <justin.tee@xxxxxxxxxxxx>
Signed-off-by: Justin Tee <justin.tee@xxxxxxxxxxxx>
Signed-off-by: James Smart <jsmart2021@xxxxxxxxx>
---
drivers/scsi/lpfc/lpfc.h | 29 ++++++
drivers/scsi/lpfc/lpfc_attr.c | 5 -
drivers/scsi/lpfc/lpfc_crtn.h | 4 +
drivers/scsi/lpfc/lpfc_hw4.h | 32 ++++++
drivers/scsi/lpfc/lpfc_init.c | 188 ++++++++++++++++++++++++++++++++++
drivers/scsi/lpfc/lpfc_sli.c | 110 ++++++++++++++++++++
6 files changed, 363 insertions(+), 5 deletions(-)
diff --git a/drivers/scsi/lpfc/lpfc.h b/drivers/scsi/lpfc/lpfc.h
index 169cef789f73..5a356a1d517c 100644
--- a/drivers/scsi/lpfc/lpfc.h
+++ b/drivers/scsi/lpfc/lpfc.h
@@ -114,6 +114,12 @@ struct lpfc_sli2_slim;
#define LPFC_MBX_NO_WAIT 0
#define LPFC_MBX_WAIT 1
+#define LPFC_CFG_PARAM_MAGIC_NUM 0xFEAA0005
+#define LPFC_PORT_CFG_NAME "/cfg/port.cfg"
+
+#define lpfc_rangecheck(val, min, max) \
+ ((uint)(val) >= (uint)(min) && (val) <= (max))
+
enum lpfc_polling_flags {
ENABLE_FCP_RING_POLLING = 0x1,
DISABLE_FCP_RING_INT = 0x2
@@ -403,6 +409,26 @@ struct lpfc_trunk_link {
link3;
};
+/* Format of congestion module parameters */
+struct lpfc_cgn_param {
+ uint32_t cgn_param_magic;
+ uint8_t cgn_param_version; /* version 1 */
+ uint8_t cgn_param_mode; /* 0=off 1=managed 2=monitor only */
+#define LPFC_CFG_OFF 0
+#define LPFC_CFG_MANAGED 1
+#define LPFC_CFG_MONITOR 2
+ uint8_t cgn_rsvd1;
+ uint8_t cgn_rsvd2;
+ uint8_t cgn_param_level0;
+ uint8_t cgn_param_level1;
+ uint8_t cgn_param_level2;
+ uint8_t byte11;
+ uint8_t byte12;
+ uint8_t byte13;
+ uint8_t byte14;
+ uint8_t byte15;
+};
+
/* Max number of days of congestion data */
#define LPFC_MAX_CGN_DAYS 10
@@ -1491,6 +1517,9 @@ struct lpfc_hba {
u32 cgn_sig_freq;
u32 cgn_acqe_cnt;
+ /* Congestion parameters from flash */
+ struct lpfc_cgn_param cgn_p;
+
/* Statistics counter for ACQE cgn alarms and warnings */
struct lpfc_cgn_acqe_stat cgn_acqe_stat;
diff --git a/drivers/scsi/lpfc/lpfc_attr.c b/drivers/scsi/lpfc/lpfc_attr.c
index d16d3544084f..449409cad60d 100644
--- a/drivers/scsi/lpfc/lpfc_attr.c
+++ b/drivers/scsi/lpfc/lpfc_attr.c
@@ -2248,11 +2248,6 @@ lpfc_sriov_hw_max_virtfn_show(struct device *dev,
return scnprintf(buf, PAGE_SIZE, "%d\n", max_nr_virtfn);
}
-static inline bool lpfc_rangecheck(uint val, uint min, uint max)
-{
- return val >= min && val <= max;
-}
-
/**
* lpfc_enable_bbcr_set: Sets an attribute value.
* @phba: pointer the the adapter structure.
diff --git a/drivers/scsi/lpfc/lpfc_crtn.h b/drivers/scsi/lpfc/lpfc_crtn.h
index e7fad8cd10ee..947c4ba847f6 100644
--- a/drivers/scsi/lpfc/lpfc_crtn.h
+++ b/drivers/scsi/lpfc/lpfc_crtn.h
@@ -77,6 +77,7 @@ int lpfc_post_rq_buffer(struct lpfc_hba *phba, struct lpfc_queue *hrq,
struct lpfc_queue *drq, int count, int idx);
void lpfc_init_congestion_stat(struct lpfc_hba *phba);
void lpfc_init_congestion_buf(struct lpfc_hba *phba);
+int lpfc_sli4_cgn_params_read(struct lpfc_hba *phba);
int lpfc_config_cgn_signal(struct lpfc_hba *phba);
void lpfc_mbx_cmpl_local_config_link(struct lpfc_hba *, LPFC_MBOXQ_t *);
@@ -220,6 +221,9 @@ irqreturn_t lpfc_sli_fp_intr_handler(int, void *);
irqreturn_t lpfc_sli4_intr_handler(int, void *);
irqreturn_t lpfc_sli4_hba_intr_handler(int, void *);
+int lpfc_read_object(struct lpfc_hba *phba, char *s, uint32_t *datap,
+ uint32_t len);
+
void lpfc_sli4_cleanup_poll_list(struct lpfc_hba *phba);
int lpfc_sli4_poll_eq(struct lpfc_queue *q, uint8_t path);
void lpfc_sli4_poll_hbtimer(struct timer_list *t);
diff --git a/drivers/scsi/lpfc/lpfc_hw4.h b/drivers/scsi/lpfc/lpfc_hw4.h
index 3e81d02fb24f..973af1f86d28 100644
--- a/drivers/scsi/lpfc/lpfc_hw4.h
+++ b/drivers/scsi/lpfc/lpfc_hw4.h
@@ -1134,6 +1134,12 @@ struct lpfc_mbx_sge {
uint32_t length;
};
+struct lpfc_mbx_host_buf {
+ uint32_t length;
+ uint32_t pa_lo;
+ uint32_t pa_hi;
+};
+
struct lpfc_mbx_nembed_cmd {
struct lpfc_sli4_cfg_mhdr cfg_mhdr;
#define LPFC_SLI4_MBX_SGE_MAX_PAGES 19
@@ -1144,6 +1150,30 @@ struct lpfc_mbx_nembed_sge_virt {
void *addr[LPFC_SLI4_MBX_SGE_MAX_PAGES];
};
+struct lpfc_mbx_read_object { /* Version 0 */
+ struct mbox_header header;
+ union {
+ struct {
+ uint32_t word0;
+#define lpfc_mbx_rd_object_rlen_SHIFT 0
+#define lpfc_mbx_rd_object_rlen_MASK 0x00FFFFFF
+#define lpfc_mbx_rd_object_rlen_WORD word0
+ uint32_t rd_object_offset;
+ uint32_t rd_object_name[26];
+#define LPFC_OBJ_NAME_SZ 104 /* 26 x sizeof(uint32_t) is 104. */
+ uint32_t rd_object_cnt;
+ struct lpfc_mbx_host_buf rd_object_hbuf[4];
+ } request;
+ struct {
+ uint32_t rd_object_actual_rlen;
+ uint32_t word1;
+#define lpfc_mbx_rd_object_eof_SHIFT 31
+#define lpfc_mbx_rd_object_eof_MASK 0x1
+#define lpfc_mbx_rd_object_eof_WORD word1
+ } response;
+ } u;
+};
+
struct lpfc_mbx_eq_create {
struct mbox_header header;
union {
@@ -2339,6 +2369,7 @@ struct lpfc_mbx_redisc_fcf_tbl {
#define ADD_STATUS_OPERATION_ALREADY_ACTIVE 0x67
#define ADD_STATUS_FW_NOT_SUPPORTED 0xEB
#define ADD_STATUS_INVALID_REQUEST 0x4B
+#define ADD_STATUS_INVALID_OBJECT_NAME 0xA0
#define ADD_STATUS_FW_DOWNLOAD_HW_DISABLED 0x58
struct lpfc_mbx_sli4_config {
@@ -3893,6 +3924,7 @@ struct lpfc_mqe {
struct lpfc_mbx_unreg_fcfi unreg_fcfi;
struct lpfc_mbx_mq_create mq_create;
struct lpfc_mbx_mq_create_ext mq_create_ext;
+ struct lpfc_mbx_read_object read_object;
struct lpfc_mbx_eq_create eq_create;
struct lpfc_mbx_modify_eq_delay eq_delay;
struct lpfc_mbx_cq_create cq_create;
diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c
index 71166c24ae89..a34f667e1cd0 100644
--- a/drivers/scsi/lpfc/lpfc_init.c
+++ b/drivers/scsi/lpfc/lpfc_init.c
@@ -6113,6 +6113,194 @@ lpfc_sli4_async_grp5_evt(struct lpfc_hba *phba,
phba->sli4_hba.link_state.logical_speed);
}
+/**
+ * lpfc_cgn_params_val - Validate FW congestion parameters.
+ * @phba: pointer to lpfc hba data structure.
+ * @p_cfg_param: pointer to FW provided congestion parameters.
+ *
+ * This routine validates the congestion parameters passed
+ * by the FW to the driver via an ACQE event.
+ **/
+static void
+lpfc_cgn_params_val(struct lpfc_hba *phba, struct lpfc_cgn_param *p_cfg_param)
+{
+ spin_lock_irq(&phba->hbalock);
+
+ if (!lpfc_rangecheck(p_cfg_param->cgn_param_mode, LPFC_CFG_OFF,
+ LPFC_CFG_MONITOR)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_CGN_MGMT,
+ "6225 CMF mode param out of range: %d\n",
+ p_cfg_param->cgn_param_mode);
+ p_cfg_param->cgn_param_mode = LPFC_CFG_OFF;
+ }
+
+ spin_unlock_irq(&phba->hbalock);
+}
+
+/**
+ * lpfc_cgn_params_parse - Process a FW cong parm change event
+ * @phba: pointer to lpfc hba data structure.
+ * @p_cgn_param: pointer to a data buffer with the FW cong params.
+ * @len: the size of pdata in bytes.
+ *
+ * This routine validates the congestion management buffer signature
+ * from the FW, validates the contents and makes corrections for
+ * valid, in-range values. If the signature magic is correct and
+ * after parameter validation, the contents are copied to the driver's
+ * @phba structure. If the magic is incorrect, an error message is
+ * logged.
+ **/
+static void
+lpfc_cgn_params_parse(struct lpfc_hba *phba,
+ struct lpfc_cgn_param *p_cgn_param, uint32_t len)
+{
+ uint32_t oldmode;
+
+ /* Make sure the FW has encoded the correct magic number to
+ * validate the congestion parameter in FW memory.
+ */
+ if (p_cgn_param->cgn_param_magic == LPFC_CFG_PARAM_MAGIC_NUM) {
+ lpfc_printf_log(phba, KERN_INFO, LOG_CGN_MGMT | LOG_INIT,
+ "4668 FW cgn parm buffer data: "
+ "magic 0x%x version %d mode %d "
+ "level0 %d level1 %d "
+ "level2 %d byte13 %d "
+ "byte14 %d byte15 %d "
+ "byte11 %d byte12 %d activeMode %d\n",
+ p_cgn_param->cgn_param_magic,
+ p_cgn_param->cgn_param_version,
+ p_cgn_param->cgn_param_mode,
+ p_cgn_param->cgn_param_level0,
+ p_cgn_param->cgn_param_level1,
+ p_cgn_param->cgn_param_level2,
+ p_cgn_param->byte13,
+ p_cgn_param->byte14,
+ p_cgn_param->byte15,
+ p_cgn_param->byte11,
+ p_cgn_param->byte12,
+ phba->cmf_active_mode);
+
+ oldmode = phba->cmf_active_mode;
+
+ /* Any parameters out of range are corrected to defaults
+ * by this routine. No need to fail.
+ */
+ lpfc_cgn_params_val(phba, p_cgn_param);
+
+ /* Parameters are verified, move them into driver storage */
+ spin_lock_irq(&phba->hbalock);
+ memcpy(&phba->cgn_p, p_cgn_param,
+ sizeof(struct lpfc_cgn_param));
+
+ spin_unlock_irq(&phba->hbalock);
+
+ phba->cmf_active_mode = phba->cgn_p.cgn_param_mode;
+
+ switch (oldmode) {
+ case LPFC_CFG_OFF:
+ if (phba->cgn_p.cgn_param_mode != LPFC_CFG_OFF) {
+ /* Turning CMF on */
+
+ if (phba->link_state >= LPFC_LINK_UP) {
+ phba->cgn_reg_fpin =
+ phba->cgn_init_reg_fpin;
+ phba->cgn_reg_signal =
+ phba->cgn_init_reg_signal;
+ lpfc_issue_els_edc(phba->pport, 0);
+ }
+ }
+ break;
+ case LPFC_CFG_MANAGED:
+ switch (phba->cgn_p.cgn_param_mode) {
+ case LPFC_CFG_OFF:
+ /* Turning CMF off */
+ if (phba->link_state >= LPFC_LINK_UP)
+ lpfc_issue_els_edc(phba->pport, 0);
+ break;
+ case LPFC_CFG_MONITOR:
+ lpfc_printf_log(phba, KERN_INFO, LOG_CGN_MGMT,
+ "4661 Switch from MANAGED to "
+ "`MONITOR mode\n");
+ break;
+ }
+ break;
+ case LPFC_CFG_MONITOR:
+ switch (phba->cgn_p.cgn_param_mode) {
+ case LPFC_CFG_OFF:
+ /* Turning CMF off */
+ if (phba->link_state >= LPFC_LINK_UP)
+ lpfc_issue_els_edc(phba->pport, 0);
+ break;
+ case LPFC_CFG_MANAGED:
+ lpfc_printf_log(phba, KERN_INFO, LOG_CGN_MGMT,
+ "4662 Switch from MONITOR to "
+ "MANAGED mode\n");
+ break;
+ }
+ break;
+ }
+ } else {
+ lpfc_printf_log(phba, KERN_ERR, LOG_CGN_MGMT | LOG_INIT,
+ "4669 FW cgn parm buf wrong magic 0x%x "
+ "version %d\n", p_cgn_param->cgn_param_magic,
+ p_cgn_param->cgn_param_version);
+ }
+}
+
+/**
+ * lpfc_sli4_cgn_params_read - Read and Validate FW congestion parameters.
+ * @phba: pointer to lpfc hba data structure.
+ *
+ * This routine issues a read_object mailbox command to
+ * get the congestion management parameters from the FW
+ * parses it and updates the driver maintained values.
+ *
+ * Returns
+ * 0 if the object was empty
+ * -Eval if an error was encountered
+ * Count if bytes were read from object
+ **/
+int
+lpfc_sli4_cgn_params_read(struct lpfc_hba *phba)
+{
+ int ret = 0;
+ struct lpfc_cgn_param *p_cgn_param = NULL;
+ u32 *pdata = NULL;
+ u32 len = 0;
+
+ /* Find out if the FW has a new set of congestion parameters. */
+ len = sizeof(struct lpfc_cgn_param);
+ pdata = kzalloc(len, GFP_KERNEL);
+ ret = lpfc_read_object(phba, (char *)LPFC_PORT_CFG_NAME,
+ pdata, len);
+
+ /* 0 means no data. A negative means error. A positive means
+ * bytes were copied.
+ */
+ if (!ret) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_CGN_MGMT | LOG_INIT,
+ "4670 CGN RD OBJ returns no data\n");
+ goto rd_obj_err;
+ } else if (ret < 0) {
+ /* Some error. Just exit and return it to the caller.*/
+ goto rd_obj_err;
+ }
+
+ lpfc_printf_log(phba, KERN_INFO, LOG_CGN_MGMT | LOG_INIT,
+ "6234 READ CGN PARAMS Successful %d\n", len);
+
+ /* Parse data pointer over len and update the phba congestion
+ * parameters with values passed back. The receive rate values
+ * may have been altered in FW, but take no action here.
+ */
+ p_cgn_param = (struct lpfc_cgn_param *)pdata;
+ lpfc_cgn_params_parse(phba, p_cgn_param, len);
+
+ rd_obj_err:
+ kfree(pdata);
+ return ret;
+}
+
/**
* lpfc_sli4_async_event_proc - Process all the pending asynchronous event
* @phba: pointer to lpfc hba data structure.
diff --git a/drivers/scsi/lpfc/lpfc_sli.c b/drivers/scsi/lpfc/lpfc_sli.c
index e6d03a0cf5c1..b42c2dc49c83 100644
--- a/drivers/scsi/lpfc/lpfc_sli.c
+++ b/drivers/scsi/lpfc/lpfc_sli.c
@@ -21705,6 +21705,116 @@ struct lpfc_io_buf *lpfc_get_io_buf(struct lpfc_hba *phba,
return lpfc_cmd;
}
+/**
+ * lpfc_read_object - Retrieve object data from HBA
+ * @phba: The HBA for which this call is being executed.
+ * @rdobject: Pathname of object data we want to read.
+ * @datap: Pointer to where data will be copied to.
+ * @datasz: size of data area
+ *
+ * This routine is limited to object sizes of LPFC_BPL_SIZE (1024) or less.
+ * The data will be truncated if datasz is not large enough.
+ * Version 1 is not supported with Embedded mbox cmd, so we must use version 0.
+ * Returns the actual bytes read from the object.
+ */
+int
+lpfc_read_object(struct lpfc_hba *phba, char *rdobject, uint32_t *datap,
+ uint32_t datasz)
+{
+ struct lpfc_mbx_read_object *read_object;
+ LPFC_MBOXQ_t *mbox;
+ int rc, length, eof, j, byte_cnt = 0;
+ uint32_t shdr_status, shdr_add_status;
+ union lpfc_sli4_cfg_shdr *shdr;
+ struct lpfc_dmabuf *pcmd;
+
+ /* sanity check on queue memory */
+ if (!datap)
+ return -ENODEV;
+
+ mbox = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
+ if (!mbox)
+ return -ENOMEM;
+ length = (sizeof(struct lpfc_mbx_read_object) -
+ sizeof(struct lpfc_sli4_cfg_mhdr));
+ lpfc_sli4_config(phba, mbox, LPFC_MBOX_SUBSYSTEM_COMMON,
+ LPFC_MBOX_OPCODE_READ_OBJECT,
+ length, LPFC_SLI4_MBX_EMBED);
+ read_object = &mbox->u.mqe.un.read_object;
+ shdr = (union lpfc_sli4_cfg_shdr *)&read_object->header.cfg_shdr;
+
+ bf_set(lpfc_mbox_hdr_version, &shdr->request, LPFC_Q_CREATE_VERSION_0);
+ bf_set(lpfc_mbx_rd_object_rlen, &read_object->u.request, datasz);
+ read_object->u.request.rd_object_offset = 0;
+ read_object->u.request.rd_object_cnt = 1;
+
+ memset((void *)read_object->u.request.rd_object_name, 0,
+ LPFC_OBJ_NAME_SZ);
+ sprintf((uint8_t *)read_object->u.request.rd_object_name, rdobject);
+ for (j = 0; j < strlen(rdobject); j++)
+ read_object->u.request.rd_object_name[j] =
+ cpu_to_le32(read_object->u.request.rd_object_name[j]);
+
+ pcmd = kmalloc(sizeof(*pcmd), GFP_KERNEL);
+ if (pcmd)
+ pcmd->virt = lpfc_mbuf_alloc(phba, MEM_PRI, &pcmd->phys);
+ if (!pcmd || !pcmd->virt) {
+ kfree(pcmd);
+ mempool_free(mbox, phba->mbox_mem_pool);
+ return -ENOMEM;
+ }
+ memset((void *)pcmd->virt, 0, LPFC_BPL_SIZE);
+ read_object->u.request.rd_object_hbuf[0].pa_lo =
+ putPaddrLow(pcmd->phys);
+ read_object->u.request.rd_object_hbuf[0].pa_hi =
+ putPaddrHigh(pcmd->phys);
+ read_object->u.request.rd_object_hbuf[0].length = LPFC_BPL_SIZE;
+
+ mbox->vport = phba->pport;
+ mbox->mbox_cmpl = lpfc_sli_def_mbox_cmpl;
+ mbox->ctx_buf = NULL;
+ mbox->ctx_ndlp = NULL;
+
+ rc = lpfc_sli_issue_mbox(phba, mbox, MBX_POLL);
+ shdr_status = bf_get(lpfc_mbox_hdr_status, &shdr->response);
+ shdr_add_status = bf_get(lpfc_mbox_hdr_add_status, &shdr->response);
+
+ if (shdr_status == STATUS_FAILED &&
+ shdr_add_status == ADD_STATUS_INVALID_OBJECT_NAME) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_INIT | LOG_CGN_MGMT,
+ "4674 No port cfg file in FW.\n");
+ byte_cnt = -ENOENT;
+ } else if (shdr_status || shdr_add_status || rc) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_INIT | LOG_CGN_MGMT,
+ "2625 READ_OBJECT mailbox failed with "
+ "status x%x add_status x%x, mbx status x%x\n",
+ shdr_status, shdr_add_status, rc);
+ byte_cnt = -ENXIO;
+ } else {
+ /* Success */
+ length = read_object->u.response.rd_object_actual_rlen;
+ eof = bf_get(lpfc_mbx_rd_object_eof, &read_object->u.response);
+ lpfc_printf_log(phba, KERN_INFO, LOG_INIT | LOG_CGN_MGMT,
+ "2626 READ_OBJECT Success len %d:%d, EOF %d\n",
+ length, datasz, eof);
+
+ /* Detect the port config file exists but is empty */
+ if (!length && eof) {
+ byte_cnt = 0;
+ goto exit;
+ }
+
+ byte_cnt = length;
+ lpfc_sli_pcimem_bcopy(pcmd->virt, datap, byte_cnt);
+ }
+
+ exit:
+ lpfc_mbuf_free(phba, pcmd->virt, pcmd->phys);
+ kfree(pcmd);
+ mempool_free(mbox, phba->mbox_mem_pool);
+ return byte_cnt;
+}
+
/**
* lpfc_get_sgl_per_hdwq - Get one SGL chunk from hdwq's pool
* @phba: The HBA for which this call is being executed.
--
2.26.2
