RE: QLE2432 initiator fails to see any LUN's on one of servers while using 5QLE2464 as a target.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Tom,
Can you also share the logs of Server1(inititator) with ql2xextended_error_logging=1? It will be great if logs are from load of the driver.

Thanks,
~Saurav

> -----Original Message-----
> From: TomK <tomkcpr@xxxxxxxxxxx>
> Sent: Saturday, April 10, 2021 8:57 PM
> To: linux-scsi@xxxxxxxxxxxxxxx
> Subject: QLE2432 initiator fails to see any LUN's on one of servers while using
> 5QLE2464 as a target.
> 
> Hey Everyone,
> 
> In a basic SAN config using a few QLE2432 adapters connected to a target
> using a QLE2464 adapter via a EMC Brocade 5000B switch, one of the
> initiators fails to present a LUN after being online for sometime.  Over
> a period of time, few months, the initiator on one of the hosts stops
> showing available LUN's to the underlying VMware clients.
> 
> All the other hosts are fine, except for this specific one.  Unless that
> is, I reboot the target completely, affecting all the other working
> hosts in the process.
> 
> Digging a bit closer, I notice that the issue seems to strike an uncanny
> similarity to the following one:
> 
> ht tps://www.spinics.net/lists/linux-scsi/msg136622.html
> 
> However, I'm wondering why only one of the servers is affected and not
> the others?  Seems it is a card issue with the first host (please see
> image) however I'm not familiar with all the messages printed so can't
> be sure of the reason nor link things as effectively. Neither of the two
> ports of the HBA on Server 1 work, when in this disconnected state,
> despite switching SFP's on the Brocade switch, switching cables etc.
> That is, again, until I reboot the target entirely.
> 
> Initiator:
>                   50:01:43:80:16:77:99:38; 50:01:43:80:16:77:99:3a;
>                   50:01:43:80:16:77:99:3b; 50:01:43:80:16:77:99:39
> 
> Target:
> 		(see below)
> 
> This also started to happen a few months ago.  Everything was fine for a
> few years before that.
> 
> 
> Log snippet:
> 
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e818:
> is_send_status=1, cmd->bufflen=73728, cmd->sg_cnt=0,
> cmd->dma_data_direction=2 se_cmd[00000000cc1dc466] qp 0
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e874:2:
> qlt_free_cmd: se_cmd[00000000cc1dc466] ox_id 00e1
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e872:2:
> qlt_24xx_atio_pkt_all_vps: qla_target(0): type 6 ox_id 0110
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e818:
> is_send_status=1, cmd->bufflen=10240, cmd->sg_cnt=0,
> cmd->dma_data_direction=2 se_cmd[00000000cc1dc466] qp 0
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e874:2:
> qlt_free_cmd: se_cmd[00000000cc1dc466] ox_id 0110
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e872:2:
> qlt_24xx_atio_pkt_all_vps: qla_target(0): type d ox_id 0000
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e82e:2:
> IMMED_NOTIFY ATIO
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f826:2:
> qla_target(0): Port ID: 01:09:00 ELS opcode: 0x03 lid 7
> 50:01:43:80:16:77:99:3a
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f897:2: Linking
> sess 00000000088a6dfa [0] wwn 50:01:43:80:16:77:99:3a with PLOGI ACK to
> wwn 50:01:43:80:16:77:99:3a s_id 01:09:00, ref=1 pla 000000004bdf1d76 link 0
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-28f9:2:
> qlt_handle_login 4772 50:01:43:80:16:77:99:3a  DS 8
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-28f9:2:
> qlt_handle_login 4803 50:01:43:80:16:77:99:3a post del sess
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e801:2:
> Scheduling sess 00000000088a6dfa for deletion
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f826:2:
> qla_target(0): Exit ELS opcode: 0x03 res 0
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-290a:2:
> qlt_unreg_sess sess 00000000088a6dfa for deletion 50:01:43:80:16:77:99:3a
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-287d:2: FCPort
> 50:01:43:80:16:77:99:3a state transitioned from ONLINE to LOST -
> portid=010900.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-28a3:2: Port
> login retry 500143801677993a, lid 0x0007 retry cnt=45.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f884:2:
> qlt_free_session_done: se_sess 000000001f2eac78 / sess 00000000088a6dfa
> from port 50:01:43:80:16:77:99:3a loop_id 0x07 s_id 01:09:00 logout 1
> keep 1 els_logo 0
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f886:2:
> qlt_free_session_done: waiting for sess 00000000088a6dfa logout
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-2870:2:
> Async-logout - hdl=172 loop-id=7 portid=010900 50:01:43:80:16:77:99:3a.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-5836:2:
> Async-logout complete - 50:01:43:80:16:77:99:3a hdl=172 portid=010900
> iop0=0.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f893:2:
> qlt_logo_completion_handler: se_sess 000000001f2eac78 / sess
> 00000000088a6dfa from port 50:01:43:80:16:77:99:3a loop_id 0x07 s_id
> 01:09:00 LOGO failed: 0x0
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e872:2:
> qlt_24xx_atio_pkt_all_vps: qla_target(0): type 6 ox_id 008a
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e818:
> is_send_status=1, cmd->bufflen=4096, cmd->sg_cnt=0,
> cmd->dma_data_direction=2 se_cmd[00000000cc1dc466] qp 0
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-e874:2:
> qlt_free_cmd: se_cmd[00000000cc1dc466] ox_id 008a
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-680b:2:
> isp_abort_needed=0 loop_resync_needed=0 fcport_update_needed=0
> start_dpc=0 reset_marker_needed=0
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-680c:2:
> beacon_blink_needed=0 isp_unrecoverable=0 fcoe_ctx_reset_needed=0
> vp_dpc_needed=0 relogin_needed=1.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-4801:2: DPC
> handler waking up, dpc_flags=0x100.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-480d:2: Relogin
> scheduled.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-4800:2: DPC
> handler sleeping.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-2908:2:
> qla2x00_relogin 21:01:00:1b:32:a1:81:21 DS 0 LS 7
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-2902:2:
> qla24xx_handle_relogin_event 21:01:00:1b:32:a1:81:21 DS 0 LS 7 P 0 del 2
> cnfl           (null) rscn 0|0 login 0|0 fl 3
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-28d8:2:
> qla24xx_fcport_handle_login 21:01:00:1b:32:a1:81:21 DS 0 LS 7 P 0 fl 3
> confl           (null) rscn 0|0 login 0 retry 45 lid 4096 scan 2
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-2908:2:
> qla2x00_relogin 50:01:43:80:16:77:99:38 DS 3 LS 4
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-2902:2:
> qla24xx_handle_relogin_event 50:01:43:80:16:77:99:38 DS 3 LS 4 P 0 del 1
> cnfl           (null) rscn 0|0 login 4|18 fl 1
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-28d8:2:
> qla24xx_fcport_handle_login 50:01:43:80:16:77:99:38 DS 3 LS 4 P 0 fl 1
> confl           (null) rscn 0|0 login 18 retry 45 lid 4 scan 2
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-2908:2:
> qla2x00_relogin 50:01:43:80:16:77:99:3a DS 10 LS 3
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-2902:2:
> qla24xx_handle_relogin_event 50:01:43:80:16:77:99:3a DS 10 LS 3 P 0 del
> 1 cnfl           (null) rscn 0|0 login 8|9 fl 1
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-480e:2: Relogin end.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f887:2:
> qlt_free_session_done: sess 00000000088a6dfa logout completed
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f89a:2: se_sess
>           (null) / sess 00000000088a6dfa port 50:01:43:80:16:77:99:3a is
> gone, releasing own PLOGI (ref=1)
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-5889:2: Sending
> PLOGI ACK to wwn 50:01:43:80:16:77:99:3a s_id 01:09:00 loop_id 0x07 exch
> 0x11223c ox_id 0xae
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f801:2:
> Unregistration of sess 00000000088a6dfa 50:01:43:80:16:77:99:3a finished
> fcp_cnt 4
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-28f4:2:
> Async-nack 50:01:43:80:16:77:99:3a hndl 175 PLOGI
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-28f2:2: Async
> done-nack res 0 50:01:43:80:16:77:99:3a  type 16
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-5811:2:
> Asynchronous PORT UPDATE ignored 0007/0004/0600.
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f83d:2:
> qla_target(0): Port update async event 0x8014 occurred: updating the
> ports database (m[0]=8014, m[1]=7, m[2]=4, m[3]=600)
> Mar 28 02:40:24 mbpc-pc kernel: qla2xxx [0000:04:00.0]-f83e:2: Async MB
> 2: Got PLOGI Complete
> 
> 
> 
> 
> 
> Thanks,
> 
> 
> 
> 
> Seems similar to this issue:
> ht tps://www.spinics.net/lists/linux-scsi/msg136470.html
> 
> 
> Log link:
> 
> ht
> tps://www.microdevsys.com/WordPressDownloads/qla2xxx-hba.log-
> recent.start.end.event.txt
> 
> Infra Setup (image):
> 
> ht tps://www.microdevsys.com/WordPressImages/brocade-san-issue.png
> 
> 
> 
> Adapter details on the target.
> 
> # QLogic Corp. ISP2432-based 4Gb Fibre Channel to PCI Express HBA ^C
> You have mail in /var/spool/mail/root
> 
> 
> 
> [root@mbpc-pc 1]# lspci -vvv -s 03:00.0
> 03:00.0 Fibre Channel: QLogic Corp. ISP2432-based 4Gb Fibre Channel to
> PCI Express HBA (rev 03)
>           Subsystem: QLogic Corp. Device 0146
>           Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B- DisINTx-
>           Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>           Latency: 0, Cache Line Size: 64 bytes
>           Interrupt: pin A routed to IRQ 18
>           Region 0: I/O ports at ee00 [size=256]
>           Region 1: Memory at fdffc000 (64-bit, non-prefetchable) [size=16K]
>           [virtual] Expansion ROM at fdf00000 [disabled] [size=256K]
>           Capabilities: [44] Power Management version 2
>                   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                   Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>           Capabilities: [4c] Express (v1) Endpoint, MSI 00
>                   DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency
> L0s <4us, L1 <1us
>                           ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
>                   DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
> Unsupported+
>                           RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>                           MaxPayload 128 bytes, MaxReadReq 4096 bytes
>                   DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+
> AuxPwr- TransPend-
>                   LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s,
> Latency L0 <4us, L1 unlimited
>                           ClockPM- Surprise- LLActRep- BwNot-
>                   LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk-
>                           ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>                   LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train-
> SlotClk+ DLActive- BWMgmt- ABWMgmt-
>           Capabilities: [64] MSI: Enable- Count=1/16 Maskable- 64bit+
>                   Address: 0000000000000000  Data: 0000
>           Capabilities: [74] Vital Product Data
>                   Product Name: PCI-Express Quad Channel 4Gb Fibre
> Channel HBA
>                   Read-only fields:
>                           [PN] Part number: QLE2464
>                           [SN] Serial number: GFC0840A74113
>                           [V0] Vendor specific: PW=15W
>                           [MN] Manufacture ID: 50 58 32 36 31 30 34 30
> 31 2d 31 31 20 20 41
>                           [V1] Vendor specific: 06.12
>                           [V3] Vendor specific: 08.01.02
>                           [V4] Vendor specific: 03.29
>                           [V5] Vendor specific: 03.23
>                           [YA] Asset tag:
>                           [RV] Reserved: checksum good, 0 byte(s) reserved
>                   End
>           Capabilities: [7c] MSI-X: Enable- Count=16 Masked-
>                   Vector table: BAR=1 offset=00002000
>                   PBA: BAR=1 offset=00003000
>           Capabilities: [100 v1] Advanced Error Reporting
>                   UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
>                   UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>                   UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
>                   CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr-
>                   CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr-
>                   AERCap: First Error Pointer: 14, GenCap+ CGenEn-
> ChkCap+ ChkEn-
>           Capabilities: [138 v1] Power Budgeting <?>
>           Kernel driver in use: qla2xxx
> 
> 
> 
> Target details:
> 
> 
> [root@mbpc-pc 1]# systool -c fc_host -v
> Class = "fc_host"
> 
>     Class Device = "host0"
>     Class Device path =
> "/sys/devices/pci0000:00/0000:00:02.0/0000:01:00.0/0000:02:00.0/0000:03:00.
> 0/host0/fc_host/host0"
>       dev_loss_tmo        = "45"
>       fabric_name         = "0xffffffffffffffff"
>       issue_lip           = <store method only>
>       max_npiv_vports     = "127"
>       node_name           = "0x2002001b32c18121"
>       npiv_vports_inuse   = "0"
>       port_id             = "0x000000"
>       port_name           = "0x2102001b32c18121"
>       port_state          = "Linkdown"
>       port_type           = "Unknown"
>       speed               = "unknown"
>       supported_classes   = "Class 3"
>       supported_speeds    = "1 Gbit, 2 Gbit, 4 Gbit"
>       symbolic_name       = "QLE2464 FW:v8.06.02 DVR:v10.00.00.07-k-debug"
>       system_hostname     = ""
>       tgtid_bind_type     = "wwpn (World Wide Port Name)"
>       uevent              =
>       vport_create        = <store method only>
>       vport_delete        = <store method only>
> 
>       Device = "host0"
>       Device path =
> "/sys/devices/pci0000:00/0000:00:02.0/0000:01:00.0/0000:02:00.0/0000:03:00.
> 0/host0"
>         fw_dump             =
>         issue_logo          = <store method only>
>         nvram               = "ISP "
>         optrom_ctl          = <store method only>
>         optrom              =
>         reset               = <store method only>
>         sfp                 = ""
>         uevent              = "DEVTYPE=scsi_host"
>         vpd                 = "▒."
> 
> 
>     Class Device = "host1"
>     Class Device path =
> "/sys/devices/pci0000:00/0000:00:02.0/0000:01:00.0/0000:02:00.0/0000:03:00.
> 1/host1/fc_host/host1"
>       dev_loss_tmo        = "45"
>       fabric_name         = "0xffffffffffffffff"
>       issue_lip           = <store method only>
>       max_npiv_vports     = "127"
>       node_name           = "0x2003001b32e18121"
>       npiv_vports_inuse   = "0"
>       port_id             = "0x000000"
>       port_name           = "0x2103001b32e18121"
>       port_state          = "Linkdown"
>       port_type           = "Unknown"
>       speed               = "unknown"
>       supported_classes   = "Class 3"
>       supported_speeds    = "1 Gbit, 2 Gbit, 4 Gbit"
>       symbolic_name       = "QLE2464 FW:v8.06.02 DVR:v10.00.00.07-k-debug"
>       system_hostname     = ""
>       tgtid_bind_type     = "wwpn (World Wide Port Name)"
>       uevent              =
>       vport_create        = <store method only>
>       vport_delete        = <store method only>
> 
>       Device = "host1"
>       Device path =
> "/sys/devices/pci0000:00/0000:00:02.0/0000:01:00.0/0000:02:00.0/0000:03:00.
> 1/host1"
>         fw_dump             =
>         issue_logo          = <store method only>
>         nvram               = "ISP "
>         optrom_ctl          = <store method only>
>         optrom              =
>         reset               = <store method only>
>         sfp                 = ""
>         uevent              = "DEVTYPE=scsi_host"
>         vpd                 = "▒."
> 
> 
>     Class Device = "host2"
>     Class Device path =
> "/sys/devices/pci0000:00/0000:00:02.0/0000:01:00.0/0000:02:01.0/0000:04:00.
> 0/host2/fc_host/host2"
>       dev_loss_tmo        = "45"
>       fabric_name         = "0x100000051e903dab"
>       issue_lip           = <store method only>
>       max_npiv_vports     = "127"
>       node_name           = "0x2000001b32818121"
>       npiv_vports_inuse   = "0"
>       port_id             = "0x011300"
>       port_name           = "0x2100001b32818121"
>       port_state          = "Online"
>       port_type           = "NPort (fabric via point-to-point)"
>       speed               = "4 Gbit"
>       supported_classes   = "Class 3"
>       supported_speeds    = "1 Gbit, 2 Gbit, 4 Gbit"
>       symbolic_name       = "QLE2464 FW:v8.06.02 DVR:v10.00.00.07-k-debug"
>       system_hostname     = ""
>       tgtid_bind_type     = "wwpn (World Wide Port Name)"
>       uevent              =
>       vport_create        = <store method only>
>       vport_delete        = <store method only>
> 
>       Device = "host2"
>       Device path =
> "/sys/devices/pci0000:00/0000:00:02.0/0000:01:00.0/0000:02:01.0/0000:04:00.
> 0/host2"
>         fw_dump             =
>         issue_logo          = <store method only>
>         nvram               = "ISP "
>         optrom_ctl          = <store method only>
>         optrom              =
>         reset               = <store method only>
>         sfp                 = ""
>         uevent              = "DEVTYPE=scsi_host"
>         vpd                 = "▒."
> 
> 
>     Class Device = "host3"
>     Class Device path =
> "/sys/devices/pci0000:00/0000:00:02.0/0000:01:00.0/0000:02:01.0/0000:04:00.
> 1/host3/fc_host/host3"
>       dev_loss_tmo        = "45"
>       fabric_name         = "0x100000051e903dab"
>       issue_lip           = <store method only>
>       max_npiv_vports     = "127"
>       node_name           = "0x2001001b32a18121"
>       npiv_vports_inuse   = "0"
>       port_id             = "0x011700"
>       port_name           = "0x2101001b32a18121"
>       port_state          = "Online"
>       port_type           = "NPort (fabric via point-to-point)"
>       speed               = "4 Gbit"
>       supported_classes   = "Class 3"
>       supported_speeds    = "1 Gbit, 2 Gbit, 4 Gbit"
>       symbolic_name       = "QLE2464 FW:v8.06.02 DVR:v10.00.00.07-k-debug"
>       system_hostname     = ""
>       tgtid_bind_type     = "wwpn (World Wide Port Name)"
>       uevent              =
>       vport_create        = <store method only>
>       vport_delete        = <store method only>
> 
>       Device = "host3"
>       Device path =
> "/sys/devices/pci0000:00/0000:00:02.0/0000:01:00.0/0000:02:01.0/0000:04:00.
> 1/host3"
>         fw_dump             =
>         issue_logo          = <store method only>
>         nvram               = "ISP "
>         optrom_ctl          = <store method only>
>         optrom              =
>         reset               = <store method only>
>         sfp                 = ""
>         uevent              = "DEVTYPE=scsi_host"
>         vpd                 = "▒."
> 
> 
> [root@mbpc-pc 1]#
> 
> 
> 
> 
> --
> Thx,
> TK.





[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]

  Powered by Linux