https://bugzilla.kernel.org/show_bug.cgi?id=212337 --- Comment #12 from d gilbert (dgilbert@xxxxxxxxxxxx) --- On 2021-03-22 12:23 p.m., bugzilla-daemon@xxxxxxxxxxxxxxxxxxx wrote: > https://bugzilla.kernel.org/show_bug.cgi?id=212337 > > --- Comment #9 from Luis Chamberlain (mcgrof@xxxxxxxxxx) --- > (In reply to d gilbert from comment #8) > >>>> The scsi_debug module option that is already in place is: >>>> tur_ms_to_ready: TEST UNIT READY millisecs before initial good status >>>> (def=0) >> >> You asked how it works, try: >> modprobe scsi_debug tur_ms_to_ready=20000 >> > > That does not resolve the rmmod race against insmod: > > scsi host2: scsi_debug: version 0190 [20200710] > [ 42.213400] dev_size_mb=8, opts=0x0, submit_queues=1, statistics=0 > [ 42.217527] scsi 2:0:0:0: Direct-Access Linux scsi_debug 0190 > PQ: 0 ANSI: 7 > [ 42.223346] scsi 2:0:0:0: Attached scsi generic sg0 type 0 > [ 42.282195] scsi host2: scsi_debug: version 0190 [20200710] > [ 42.282195] dev_size_mb=8, opts=0x0, submit_queues=1, statistics=0 > [ 42.288169] scsi 2:0:0:0: Direct-Access Linux scsi_debug 0190 > PQ: 0 ANSI: 7 > [ 42.292122] sd 2:0:0:0: Attached scsi generic sg0 type 0 > [ 42.292244] sd 2:0:0:0: Power-on or device reset occurred > [ 42.302288] sd 2:0:0:0: [sda] Spinning up disk... > > Then we wait... > > [ 44.308213] ...................ready > [ 62.748919] sd 2:0:0:0: [sda] 16384 512-byte logical blocks: (8.39 MB/8.00 > MiB) > [ 62.754265] sd 2:0:0:0: [sda] Write Protect is off > [ 62.763253] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, > supports DPO and FUA > [ 62.776965] sd 2:0:0:0: [sda] Optimal transfer size 524288 bytes > [ 62.883817] sd 2:0:0:0: [sda] Attached SCSI disk > > And then rmmod still fails. > Just to explain a bit more about tur_ms_to_ready, that does not effect SCSI commands like REPORT LUNS, INQUIRY and REQUEST SENSE, but does slow down all "media access" commands including TEST UNIT READY (TUR) and READ CAPACITY. So if you watch what is happening with 'lsscsi -s' the device (LUN) will appear almost immediately but its size will be "-" due to the fact that READ CAPACITY (or TUR before it) is waiting for tur_ms_to_ready to elapse. After that the size (for disks) will be shown by 'lsscsi -s'. When you say 'rmmod still fails' do you mean it refuses to remove the module because the device is busy? It is busy, where is the race?. What precisely would you like to happen? What does a real SCSI HBA do? Is there any way that a driver can detect that rmmod has been called and rejected? If not, we could add a "shutdown" writable attribute in /sys/bus/pseudo/drivers/scsi_debug/ . Then if a large number of pseudo devices is being built due to the modprobe invocation, the driver can go into reverse by checking that attribute before it adds another host (target or LUN?). After shutdown, the driver is still active, just with no hosts, and thus no LUNs. A more accurate name would be rm_all_hosts . Doug Gilbert -- You may reply to this email to add a comment. You are receiving this mail because: You are watching the assignee of the bug.
