On 19/03/2021 01:43, Jason Yan wrote:
在 2021/3/19 6:56, Jolly Shah 写道:
When the cache_type for the scsi device is changed, the scsi layer
issues a MODE_SELECT command. The caching mode details are communicated
via a request buffer associated with the scsi command with data
direction set as DMA_TO_DEVICE (scsi_mode_select). When this command
reaches the libata layer, as a part of generic initial setup, libata
layer sets up the scatterlist for the command using the scsi command
(ata_scsi_qc_new). This command is then translated by the libata layer
into ATA_CMD_SET_FEATURES (ata_scsi_mode_select_xlat). The libata layer
treats this as a non data command (ata_mselect_caching), since it only
needs an ata taskfile to pass the caching on/off information to the
device. It does not need the scatterlist that has been setup, so it does
not perform dma_map_sg on the scatterlist (ata_qc_issue). Unfortunately,
when this command reaches the libsas layer(sas_ata_qc_issue), libsas
layer sees it as a non data command with a scatterlist. It cannot
extract the correct dma length, since the scatterlist has not been
mapped with dma_map_sg for a DMA operation. When this partially
constructed SAS task reaches pm80xx LLDD, it results in below warning.
"pm80xx_chip_sata_req 6058: The sg list address
start_addr=0x0000000000000000 data_len=0x0end_addr_high=0xffffffff
end_addr_low=0xffffffff has crossed 4G boundary"
This patch updates code to handle ata non data commands separately so
num_scatter and total_xfer_len remain 0.
Fixes: 53de092f47ff ("scsi: libsas: Set data_dir as DMA_NONE if libata
marks qc as NODATA")
Signed-off-by: Jolly Shah <jollys@xxxxxxxxxx>
Reviewed-by: John Garry <john.garry@xxxxxxxxxx>
@luojiaxing, can you please test this?
---
v2:
- reorganized code to avoid setting num_scatter twice
drivers/scsi/libsas/sas_ata.c | 9 ++++-----
1 file changed, 4 insertions(+), 5 deletions(-)
diff --git a/drivers/scsi/libsas/sas_ata.c
b/drivers/scsi/libsas/sas_ata.c
index 024e5a550759..8b9a39077dba 100644
--- a/drivers/scsi/libsas/sas_ata.c
+++ b/drivers/scsi/libsas/sas_ata.c
@@ -201,18 +201,17 @@ static unsigned int sas_ata_qc_issue(struct
ata_queued_cmd *qc)
memcpy(task->ata_task.atapi_packet, qc->cdb, qc->dev->cdb_len);
task->total_xfer_len = qc->nbytes;
task->num_scatter = qc->n_elem;
+ task->data_dir = qc->dma_dir;
+ } else if (qc->tf.protocol == ATA_PROT_NODATA) {
+ task->data_dir = DMA_NONE;
Hi Jolly & John,
We only set DMA_NONE for ATA_PROT_NODATA, I'm curious about why
ATA_PROT_NCQ_NODATA and ATAPI_PROT_NODATA do not need to set DMA_NONE?
So we can see something like atapi_eh_tur() -> ata_exec_internal(),
which is a ATAPI NONDATA and has DMA_NONE, so should be ok.
Other cases, like those using the xlate function on the qc for
ATA_PROT_NCQ_NODATA, could be checked further.
For now, we're just trying to fix the fix.
Thanks,
Jason
} else {
for_each_sg(qc->sg, sg, qc->n_elem, si)
xfer += sg_dma_len(sg);
task->total_xfer_len = xfer;
task->num_scatter = si;
- }
-
- if (qc->tf.protocol == ATA_PROT_NODATA)
- task->data_dir = DMA_NONE;
- else
task->data_dir = qc->dma_dir;
+ }
task->scatter = qc->sg;
task->ata_task.retry_count = 1;
task->task_state_flags = SAS_TASK_STATE_PENDING;
.
