Re: [PATCH] scsi: libsas: Reset num_scatter if libata mark qc as NODATA

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 16/03/2021 19:39, Jolly Shah wrote:
When the cache_type for the scsi device is changed, the scsi layer
issues a MODE_SELECT command. The caching mode details are communicated
via a request buffer associated with the scsi command with data
direction set as DMA_TO_DEVICE (scsi_mode_select). When this command
reaches the libata layer, as a part of generic initial setup, libata
layer sets up the scatterlist for the command using the scsi command
(ata_scsi_qc_new). This command is then translated by the libata layer
into ATA_CMD_SET_FEATURES (ata_scsi_mode_select_xlat). The libata layer
treats this as a non data command (ata_mselect_caching), since it only
needs an ata taskfile to pass the caching on/off information to the
device. It does not need the scatterlist that has been setup, so it does
not perform dma_map_sg on the scatterlist (ata_qc_issue).

So if we don't perform the dma_map_sg() on the sgl at this point, then it seems to me that we should not perform for_each_sg() on it either, right? That is still what happens in sas_ata_qc_issue() in this case.

Unfortunately,
when this command reaches the libsas layer(sas_ata_qc_issue), libsas
layer sees it as a non data command with a scatterlist. It cannot
extract the correct dma length, since the scatterlist has not been
mapped with dma_map_sg for a DMA operation. When this partially
constructed SAS task reaches pm80xx LLDD, it results in below warning.

"pm80xx_chip_sata_req 6058: The sg list address
start_addr=0x0000000000000000 data_len=0x0end_addr_high=0xffffffff
end_addr_low=0xffffffff has crossed 4G boundary"

This patch assigns appropriate value to  num_sectors for ata non data
commands.

Signed-off-by: Jolly Shah <jollys@xxxxxxxxxx>
---
  drivers/scsi/libsas/sas_ata.c | 6 ++++--
  1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/libsas/sas_ata.c b/drivers/scsi/libsas/sas_ata.c
index 024e5a550759..94ec08cebbaa 100644
--- a/drivers/scsi/libsas/sas_ata.c
+++ b/drivers/scsi/libsas/sas_ata.c
@@ -209,10 +209,12 @@ static unsigned int sas_ata_qc_issue(struct ata_queued_cmd *qc)
  		task->num_scatter = si;
  	}
- if (qc->tf.protocol == ATA_PROT_NODATA)
+	if (qc->tf.protocol == ATA_PROT_NODATA) {
  		task->data_dir = DMA_NONE;
-	else
+		task->num_scatter = 0;

task->num_scatter has already been set in this function. Best not set it twice.

Thanks,
John

+	} else {
  		task->data_dir = qc->dma_dir;
+	}
  	task->scatter = qc->sg;
  	task->ata_task.retry_count = 1;
  	task->task_state_flags = SAS_TASK_STATE_PENDING;





[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]

  Powered by Linux