Fixes the following W=1 kernel build warning(s): drivers/scsi/isci/phy.c:354: warning: Function parameter or member 'iphy' not described in 'phy_get_non_dummy_port' drivers/scsi/isci/phy.c:354: warning: expecting prototype for If the phy is(). Prototype was for phy_get_non_dummy_port() instead drivers/scsi/isci/phy.c:364: warning: wrong kernel-doc identifier on line: drivers/scsi/isci/phy.c:401: warning: wrong kernel-doc identifier on line: drivers/scsi/isci/phy.c:611: warning: Function parameter or member 'iphy' not described in 'sci_phy_complete_link_training' drivers/scsi/isci/phy.c:611: warning: Excess function parameter 'sci_phy' description in 'sci_phy_complete_link_training' drivers/scsi/isci/phy.c:1170: warning: Cannot understand * drivers/scsi/isci/phy.c:1222: warning: Cannot understand * drivers/scsi/isci/phy.c:1432: warning: Function parameter or member 'sas_phy' not described in 'isci_phy_control' drivers/scsi/isci/phy.c:1432: warning: Excess function parameter 'phy' description in 'isci_phy_control' Cc: Artur Paszkiewicz <artur.paszkiewicz@xxxxxxxxx> Cc: "James E.J. Bottomley" <jejb@xxxxxxxxxxxxx> Cc: "Martin K. Petersen" <martin.petersen@xxxxxxxxxx> Cc: linux-scsi@xxxxxxxxxxxxxxx Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx> --- drivers/scsi/isci/phy.c | 21 ++++++++++----------- 1 file changed, 10 insertions(+), 11 deletions(-) diff --git a/drivers/scsi/isci/phy.c b/drivers/scsi/isci/phy.c index 1b87d9080ebeb..7ca7621f77479 100644 --- a/drivers/scsi/isci/phy.c +++ b/drivers/scsi/isci/phy.c @@ -361,11 +361,9 @@ struct isci_port *phy_get_non_dummy_port(struct isci_phy *iphy) } /** - * This method will assign a port to the phy object. + * sci_phy_set_port() - This method will assign a port to the phy object. * @out]: iphy This parameter specifies the phy for which to assign a port * object. - * - * */ void sci_phy_set_port( struct isci_phy *iphy, @@ -398,11 +396,11 @@ enum sci_status sci_phy_initialize(struct isci_phy *iphy, } /** - * This method assigns the direct attached device ID for this phy. + * sci_phy_setup_transport() - This method assigns the direct attached device ID for this phy. * - * @iphy The phy for which the direct attached device id is to + * @iphy: The phy for which the direct attached device id is to * be assigned. - * @device_id The direct attached device ID to assign to the phy. + * @device_id: The direct attached device ID to assign to the phy. * This will either be the RNi for the device or an invalid RNi if there * is no current device assigned to the phy. */ @@ -597,7 +595,7 @@ static void sci_phy_start_sata_link_training(struct isci_phy *iphy) /** * sci_phy_complete_link_training - perform processing common to * all protocols upon completion of link training. - * @sci_phy: This parameter specifies the phy object for which link training + * @iphy: This parameter specifies the phy object for which link training * has completed. * @max_link_rate: This parameter specifies the maximum link rate to be * associated with this phy. @@ -1167,8 +1165,8 @@ static void sci_phy_starting_final_substate_enter(struct sci_base_state_machine } /** - * - * @sci_phy: This is the struct isci_phy object to stop. + * scu_link_layer_stop_protocol_engine() + * @iphy: This is the struct isci_phy object to stop. * * This method will stop the struct isci_phy object. This does not reset the * protocol engine it just suspends it and places it in a state where it will @@ -1219,7 +1217,8 @@ static void scu_link_layer_start_oob(struct isci_phy *iphy) } /** - * + * scu_link_layer_tx_hard_reset() + * @iphy: This is the struct isci_phy object to stop. * * This method will transmit a hard reset request on the specified phy. The SCU * hardware requires that we reset the OOB state machine and set the hard reset @@ -1420,7 +1419,7 @@ void isci_phy_init(struct isci_phy *iphy, struct isci_host *ihost, int index) /** * isci_phy_control() - This function is one of the SAS Domain Template * functions. This is a phy management function. - * @phy: This parameter specifies the sphy being controlled. + * @sas_phy: This parameter specifies the sphy being controlled. * @func: This parameter specifies the phy control function being invoked. * @buf: This parameter is specific to the phy function being invoked. * -- 2.27.0
