[PATCH 3/8] scsi: nsp32: Remove or exclude unused variables

[Lee Jones <lee.jones@xxxxxxxxxx>]

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/nsp32.c: In function ‘nsp32_selection_autoscsi’:
 drivers/scsi/nsp32.c:584:17: warning: variable ‘execph’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/nsp32.c: In function ‘nsp32_msgout_occur’:
 drivers/scsi/nsp32.c:1785:7: warning: variable ‘new_sgtp’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/nsp32.c: In function ‘nsp32_analyze_sdtr’:
 drivers/scsi/nsp32.c:2227:20: warning: variable ‘syncnum’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/nsp32.c:2223:20: warning: variable ‘synct’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/nsp32.c: In function ‘nsp32_do_bus_reset’:
 drivers/scsi/nsp32.c:2841:17: warning: variable ‘intrdat’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/nsp32.c: In function ‘nsp32_getprom_param’:
 drivers/scsi/nsp32.c:2912:11: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]

Cc: GOTO Masanori <gotom@xxxxxxxxxxxx>
Cc: YOKOTA Hiroshi <yokota@xxxxxxxxxxxxxxxxxxxxxxx>
Cc: "James E.J. Bottomley" <jejb@xxxxxxxxxxxxx>
Cc: "Martin K. Petersen" <martin.petersen@xxxxxxxxxx>
Cc: gotom@xxxxxxxxxx
Cc: linux-scsi@xxxxxxxxxxxxxxx
Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
---
 drivers/scsi/nsp32.c | 23 ++++-------------------
 1 file changed, 4 insertions(+), 19 deletions(-)

diff --git a/drivers/scsi/nsp32.c b/drivers/scsi/nsp32.c
index d5aa96f05bce4..54abda4d07c64 100644
--- a/drivers/scsi/nsp32.c
+++ b/drivers/scsi/nsp32.c
@@ -581,7 +581,6 @@ static int nsp32_selection_autoscsi(struct scsi_cmnd *SCpnt)
 	int		status;
 	unsigned short	command	= 0;
 	unsigned int	msgout  = 0;
-	unsigned short	execph;
 	int		i;
 
 	nsp32_dbg(NSP32_DEBUG_AUTOSCSI, "in");
@@ -605,7 +604,7 @@ static int nsp32_selection_autoscsi(struct scsi_cmnd *SCpnt)
 	/*
 	 * clear execph
 	 */
-	execph = nsp32_read2(base, SCSI_EXECUTE_PHASE);
+	nsp32_read2(base, SCSI_EXECUTE_PHASE);
 
 	/*
 	 * clear FIFO counter to set CDBs
@@ -1781,8 +1780,6 @@ static void nsp32_msgout_occur(struct scsi_cmnd *SCpnt)
 {
 	nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata;
 	unsigned int base   = SCpnt->device->host->io_port;
-	//unsigned short command;
-	long new_sgtp;
 	int i;
 	
 	nsp32_dbg(NSP32_DEBUG_MSGOUTOCCUR,
@@ -1796,14 +1793,6 @@ static void nsp32_msgout_occur(struct scsi_cmnd *SCpnt)
 		nsp32_build_nop(SCpnt);
 	}
 
-	/*
-	 * Set SGTP ADDR current entry for restarting AUTOSCSI, 
-	 * because SGTP is incremented next point.
-	 * There is few statement in the specification...
-	 */
- 	new_sgtp = data->cur_lunt->sglun_paddr + 
-		   (data->cur_lunt->cur_entry * sizeof(nsp32_sgtable));
-
 	/*
 	 * send messages
 	 */
@@ -2220,17 +2209,12 @@ static void nsp32_analyze_sdtr(struct scsi_cmnd *SCpnt)
 {
 	nsp32_hw_data   *data = (nsp32_hw_data *)SCpnt->device->host->hostdata;
 	nsp32_target     *target     = data->cur_target;
-	nsp32_sync_table *synct;
 	unsigned char     get_period = data->msginbuf[3];
 	unsigned char     get_offset = data->msginbuf[4];
 	int               entry;
-	int               syncnum;
 
 	nsp32_dbg(NSP32_DEBUG_MSGINOCCUR, "enter");
 
-	synct   = data->synct;
-	syncnum = data->syncnum;
-
 	/*
 	 * If this inititor sent the SDTR message, then target responds SDTR,
 	 * initiator SYNCREG, ACKWIDTH from SDTR parameter.
@@ -2838,8 +2822,8 @@ static int nsp32_eh_abort(struct scsi_cmnd *SCpnt)
 static void nsp32_do_bus_reset(nsp32_hw_data *data)
 {
 	unsigned int   base = data->BaseAddress;
-	unsigned short intrdat;
 	int i;
+	unsigned short __maybe_unused intrdat;
 
 	nsp32_dbg(NSP32_DEBUG_BUSRESET, "in");
 
@@ -2909,7 +2893,8 @@ static int nsp32_getprom_param(nsp32_hw_data *data)
 {
 	int vendor = data->pci_devid->vendor;
 	int device = data->pci_devid->device;
-	int ret, val, i;
+	int ret, i;
+	int __maybe_unused val;
 
 	/*
 	 * EEPROM checking.
-- 
2.27.0