Re: [PATCH v1 1/2] scsi: dt-bindings: ufs: Add vcc-voltage-level for UFS

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2020-09-18 12:01, Rob Herring wrote:
On Tue, Sep 15, 2020 at 2:10 AM <nguyenb@xxxxxxxxxxxxxx> wrote:

On 2020-09-14 11:35, Rob Herring wrote:
> On Mon, Aug 31, 2020 at 11:00:47PM -0700, Bao D. Nguyen wrote:
>> UFS's specifications supports a range of Vcc operating
>> voltage levels. Add documentation for the UFS's Vcc voltage
>> levels setting.
>>
>> Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx>
>> Signed-off-by: Asutosh Das <asutoshd@xxxxxxxxxxxxxx>
>> Signed-off-by: Bao D. Nguyen <nguyenb@xxxxxxxxxxxxxx>
>> ---
>>  Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt | 2 ++
>>  1 file changed, 2 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> index 415ccdd..7257b32 100644
>> --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> @@ -23,6 +23,8 @@ Optional properties:
>>                            with "phys" attribute, provides phandle to
>> UFS PHY node
>>  - vdd-hba-supply        : phandle to UFS host controller supply
>> regulator node
>>  - vcc-supply            : phandle to VCC supply regulator node
>> +- vcc-voltage-level     : specifies voltage levels for VCC supply.
>> +                          Should be specified in pairs (min, max),
>> units uV.
>
> The expectation is the regulator pointed to by 'vcc-supply' has the
> voltage constraints. Those constraints are supposed to be the board
> constraints, not the regulator operating design constraints. If that
> doesn't work for your case, then it should be addressed in a common way
> for the regulator binding.
The UFS regulator has a min_uV and max_uV limits. Currently, the min and
max are hardcoded
to UFS2.1 Spec allowed values of 2.7V and 3.6V respectively.
With this change, I am trying to fix a couple issues:
1. The 2.7V min value only applies to UFS2.1 devices. with UFS3.0+
devices, the VCC min should be 2.4V.
Hardcoding the min_uV to 2.7V does not work for UFS3.0+ devices.

Don't you know the device version attached and can adjust the voltage
based on that? Or you have to set the voltage first?
Yes it is one of the solutions. Once detect the UFS device is version 3.0+, you can lower the voltage to 2.5V from the hardcoded value used by the driver. However, to change the Vcc voltage, the host needs to follow a sequence to ensure safe operations after Vcc change (device has to be in sleep mode, Vcc needs to go down to 0 then up to 2.5V.) Also same sequence is repeated for every host initialization which is inconvenient.


2. Allow users to select a different Vcc voltage within the allowed
range.
Using the min value, the UFS device is operating at marginal Vcc
voltage.
In addition the PMIC and the board designs may add some variables
especially at extreme
temperatures. We observe stability issues when using the min Vcc
voltage.

Again, we have standard regulator properties for this already that you
can tune per board.
Thank you for the suggestion.


Rob



[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]

  Powered by Linux