On 2020/09/18 8:18, Keith Busch wrote: > From: Damien Le Moal <damien.lemoal@xxxxxxx> > > Add missing Additional Sense Codes listed in > http://www.t10.org/lists/asc-num.txt. > > Signed-off-by: Damien Le Moal <damien.lemoal@xxxxxxx> Martin already pulled this one in scsi-staging. So you can drop it from this series. > --- > drivers/scsi/sense_codes.h | 54 +++++++++++++++++++++++++++++++++++++- > 1 file changed, 53 insertions(+), 1 deletion(-) > > diff --git a/drivers/scsi/sense_codes.h b/drivers/scsi/sense_codes.h > index 201a536688de..805d4c13d070 100644 > --- a/drivers/scsi/sense_codes.h > +++ b/drivers/scsi/sense_codes.h > @@ -1,7 +1,7 @@ > /* SPDX-License-Identifier: GPL-2.0 */ > /* > * The canonical list of T10 Additional Sense Codes is available at: > - * http://www.t10.org/lists/asc-num.txt [most recent: 20141221] > + * http://www.t10.org/lists/asc-num.txt [most recent: 20200817] > */ > > SENSE_CODE(0x0000, "No additional sense information") > @@ -29,6 +29,7 @@ SENSE_CODE(0x001E, "Conflicting SA creation request") > SENSE_CODE(0x001F, "Logical unit transitioning to another power condition") > SENSE_CODE(0x0020, "Extended copy information available") > SENSE_CODE(0x0021, "Atomic command aborted due to ACA") > +SENSE_CODE(0x0022, "Deferred microcode is pending") > > SENSE_CODE(0x0100, "No index/sector signal") > > @@ -72,6 +73,9 @@ SENSE_CODE(0x041F, "Logical unit not ready, microcode download required") > SENSE_CODE(0x0420, "Logical unit not ready, logical unit reset required") > SENSE_CODE(0x0421, "Logical unit not ready, hard reset required") > SENSE_CODE(0x0422, "Logical unit not ready, power cycle required") > +SENSE_CODE(0x0423, "Logical unit not ready, affiliation required") > +SENSE_CODE(0x0424, "Depopulation in progress") > +SENSE_CODE(0x0425, "Depopulation restoration in progress") > > SENSE_CODE(0x0500, "Logical unit does not respond to selection") > > @@ -104,6 +108,17 @@ SENSE_CODE(0x0B06, "Warning - non-volatile cache now volatile") > SENSE_CODE(0x0B07, "Warning - degraded power to non-volatile cache") > SENSE_CODE(0x0B08, "Warning - power loss expected") > SENSE_CODE(0x0B09, "Warning - device statistics notification active") > +SENSE_CODE(0x0B0A, "Warning - high critical temperature limit exceeded") > +SENSE_CODE(0x0B0B, "Warning - low critical temperature limit exceeded") > +SENSE_CODE(0x0B0C, "Warning - high operating temperature limit exceeded") > +SENSE_CODE(0x0B0D, "Warning - low operating temperature limit exceeded") > +SENSE_CODE(0x0B0E, "Warning - high critical humidity limit exceeded") > +SENSE_CODE(0x0B0F, "Warning - low critical humidity limit exceeded") > +SENSE_CODE(0x0B10, "Warning - high operating humidity limit exceeded") > +SENSE_CODE(0x0B11, "Warning - low operating humidity limit exceeded") > +SENSE_CODE(0x0B12, "Warning - microcode security at risk") > +SENSE_CODE(0x0B13, "Warning - microcode digital signature validation failure") > +SENSE_CODE(0x0B14, "Warning - physical element status change") > > SENSE_CODE(0x0C00, "Write error") > SENSE_CODE(0x0C01, "Write error - recovered with auto reallocation") > @@ -122,6 +137,8 @@ SENSE_CODE(0x0C0D, "Write error - not enough unsolicited data") > SENSE_CODE(0x0C0E, "Multiple write errors") > SENSE_CODE(0x0C0F, "Defects in error window") > SENSE_CODE(0x0C10, "Incomplete multiple atomic write operations") > +SENSE_CODE(0x0C11, "Write error - recovery scan needed") > +SENSE_CODE(0x0C12, "Write error - insufficient zone resources") > > SENSE_CODE(0x0D00, "Error detected by third party temporary initiator") > SENSE_CODE(0x0D01, "Third party device failure") > @@ -242,6 +259,9 @@ SENSE_CODE(0x2009, "Access denied - invalid LU identifier") > SENSE_CODE(0x200A, "Access denied - invalid proxy token") > SENSE_CODE(0x200B, "Access denied - ACL LUN conflict") > SENSE_CODE(0x200C, "Illegal command when not in append-only mode") > +SENSE_CODE(0x200D, "Not an administrative logical unit") > +SENSE_CODE(0x200E, "Not a subsidiary logical unit") > +SENSE_CODE(0x200F, "Not a conglomerate logical unit") > > SENSE_CODE(0x2100, "Logical block address out of range") > SENSE_CODE(0x2101, "Invalid element address") > @@ -251,6 +271,8 @@ SENSE_CODE(0x2104, "Unaligned write command") > SENSE_CODE(0x2105, "Write boundary violation") > SENSE_CODE(0x2106, "Attempt to read invalid data") > SENSE_CODE(0x2107, "Read boundary violation") > +SENSE_CODE(0x2108, "Misaligned write command") > +SENSE_CODE(0x2109, "Attempt to access gap zone") > > SENSE_CODE(0x2200, "Illegal function (use 20 00, 24 00, or 26 00)") > > @@ -275,6 +297,7 @@ SENSE_CODE(0x2405, "Security working key frozen") > SENSE_CODE(0x2406, "Nonce not unique") > SENSE_CODE(0x2407, "Nonce timestamp out of range") > SENSE_CODE(0x2408, "Invalid XCDB") > +SENSE_CODE(0x2409, "Invalid fast format") > > SENSE_CODE(0x2500, "Logical unit not supported") > > @@ -297,6 +320,10 @@ SENSE_CODE(0x260F, "Invalid data-out buffer integrity check value") > SENSE_CODE(0x2610, "Data decryption key fail limit reached") > SENSE_CODE(0x2611, "Incomplete key-associated data set") > SENSE_CODE(0x2612, "Vendor specific key reference not found") > +SENSE_CODE(0x2613, "Application tag mode page is invalid") > +SENSE_CODE(0x2614, "Tape stream mirroring prevented") > +SENSE_CODE(0x2615, "Copy source or copy destination not authorized") > +SENSE_CODE(0x2616, "Fast copy not possible") > > SENSE_CODE(0x2700, "Write protected") > SENSE_CODE(0x2701, "Hardware write protected") > @@ -342,6 +369,7 @@ SENSE_CODE(0x2A12, "Data encryption parameters changed by vendor specific event" > SENSE_CODE(0x2A13, "Data encryption key instance counter has changed") > SENSE_CODE(0x2A14, "SA creation capabilities data has changed") > SENSE_CODE(0x2A15, "Medium removal prevention preempted") > +SENSE_CODE(0x2A16, "Zone reset write pointer recommended") > > SENSE_CODE(0x2B00, "Copy cannot execute since host cannot disconnect") > > @@ -360,6 +388,11 @@ SENSE_CODE(0x2C0B, "Not reserved") > SENSE_CODE(0x2C0C, "Orwrite generation does not match") > SENSE_CODE(0x2C0D, "Reset write pointer not allowed") > SENSE_CODE(0x2C0E, "Zone is offline") > +SENSE_CODE(0x2C0F, "Stream not open") > +SENSE_CODE(0x2C10, "Unwritten data in zone") > +SENSE_CODE(0x2C11, "Descriptor format sense data required") > +SENSE_CODE(0x2C12, "Zone is inactive") > +SENSE_CODE(0x2C13, "Well known logical unit access required") > > SENSE_CODE(0x2D00, "Overwrite error on update in place") > > @@ -395,6 +428,8 @@ SENSE_CODE(0x3100, "Medium format corrupted") > SENSE_CODE(0x3101, "Format command failed") > SENSE_CODE(0x3102, "Zoned formatting failed due to spare linking") > SENSE_CODE(0x3103, "Sanitize command failed") > +SENSE_CODE(0x3104, "Depopulation failed") > +SENSE_CODE(0x3105, "Depopulation restoration failed") > > SENSE_CODE(0x3200, "No defect spare location available") > SENSE_CODE(0x3201, "Defect list update failure") > @@ -419,6 +454,7 @@ SENSE_CODE(0x3802, "Esn - power management class event") > SENSE_CODE(0x3804, "Esn - media class event") > SENSE_CODE(0x3806, "Esn - device busy class event") > SENSE_CODE(0x3807, "Thin Provisioning soft threshold reached") > +SENSE_CODE(0x3808, "Depopulation interrupted") > > SENSE_CODE(0x3900, "Saving parameters not supported") > > @@ -456,6 +492,7 @@ SENSE_CODE(0x3B19, "Element enabled") > SENSE_CODE(0x3B1A, "Data transfer device removed") > SENSE_CODE(0x3B1B, "Data transfer device inserted") > SENSE_CODE(0x3B1C, "Too many logical objects on partition to support operation") > +SENSE_CODE(0x3B20, "Element static information changed") > > SENSE_CODE(0x3D00, "Invalid bits in identify message") > > @@ -488,6 +525,11 @@ SENSE_CODE(0x3F13, "iSCSI IP address removed") > SENSE_CODE(0x3F14, "iSCSI IP address changed") > SENSE_CODE(0x3F15, "Inspect referrals sense descriptors") > SENSE_CODE(0x3F16, "Microcode has been changed without reset") > +SENSE_CODE(0x3F17, "Zone transition to full") > +SENSE_CODE(0x3F18, "Bind completed") > +SENSE_CODE(0x3F19, "Bind redirected") > +SENSE_CODE(0x3F1A, "Subsidiary binding changed") > + > /* > * SENSE_CODE(0x40NN, "Ram failure") > * SENSE_CODE(0x40NN, "Diagnostic failure on component nn") > @@ -589,6 +631,9 @@ SENSE_CODE(0x550B, "Insufficient power for operation") > SENSE_CODE(0x550C, "Insufficient resources to create rod") > SENSE_CODE(0x550D, "Insufficient resources to create rod token") > SENSE_CODE(0x550E, "Insufficient zone resources") > +SENSE_CODE(0x550F, "Insufficient zone resources to complete write") > +SENSE_CODE(0x5510, "Maximum number of streams open") > +SENSE_CODE(0x5511, "Insufficient resources to bind") > > SENSE_CODE(0x5700, "Unable to recover table-of-contents") > > @@ -692,6 +737,7 @@ SENSE_CODE(0x5D69, "Firmware impending failure throughput performance") > SENSE_CODE(0x5D6A, "Firmware impending failure seek time performance") > SENSE_CODE(0x5D6B, "Firmware impending failure spin-up retry count") > SENSE_CODE(0x5D6C, "Firmware impending failure drive calibration retry count") > +SENSE_CODE(0x5D73, "Media impending failure endurance limit met") > SENSE_CODE(0x5DFF, "Failure prediction threshold exceeded (false)") > > SENSE_CODE(0x5E00, "Low power condition on") > @@ -744,6 +790,8 @@ SENSE_CODE(0x6708, "Assign failure occurred") > SENSE_CODE(0x6709, "Multiply assigned logical unit") > SENSE_CODE(0x670A, "Set target port groups command failed") > SENSE_CODE(0x670B, "ATA device feature not enabled") > +SENSE_CODE(0x670C, "Command rejected") > +SENSE_CODE(0x670D, "Explicit bind not allowed") > > SENSE_CODE(0x6800, "Logical unit not configured") > SENSE_CODE(0x6801, "Subsidiary logical unit not configured") > @@ -772,6 +820,10 @@ SENSE_CODE(0x6F04, "Media region code is mismatched to logical unit region") > SENSE_CODE(0x6F05, "Drive region must be permanent/region reset count error") > SENSE_CODE(0x6F06, "Insufficient block count for binding nonce recording") > SENSE_CODE(0x6F07, "Conflict in binding nonce recording") > +SENSE_CODE(0x6F08, "Insufficient permission") > +SENSE_CODE(0x6F09, "Invalid drive-host pairing server") > +SENSE_CODE(0x6F0A, "Drive-host pairing suspended") > + > /* > * SENSE_CODE(0x70NN, "Decompression exception short algorithm id of nn") > */ > -- Damien Le Moal Western Digital Research
