Hi Asutosh,
On 2020-07-29 02:06, Asutosh Das (asd) wrote:
On 7/27/2020 10:00 PM, Can Guo wrote:
Sometime dumps in IRQ handler are heavy enough to cause system
stability
issues, move them to error handler.
Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx>
---
drivers/scsi/ufs/ufshcd.c | 31 +++++++++++++++----------------
1 file changed, 15 insertions(+), 16 deletions(-)
diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index c480823..b2bafa3 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -5682,6 +5682,21 @@ static void ufshcd_err_handler(struct
work_struct *work)
UFSHCD_UIC_DL_TCx_REPLAY_ERROR))))
needs_reset = true;
+ if (hba->saved_err & (INT_FATAL_ERRORS | UIC_ERROR |
+ UFSHCD_UIC_HIBERN8_MASK)) {
+ bool pr_prdt = !!(hba->saved_err & SYSTEM_BUS_FATAL_ERROR);
+
+ dev_err(hba->dev, "%s: saved_err 0x%x saved_uic_err 0x%x\n",
+ __func__, hba->saved_err, hba->saved_uic_err);
+ spin_unlock_irqrestore(hba->host->host_lock, flags);
+ ufshcd_print_host_state(hba);
+ ufshcd_print_pwr_info(hba);
+ ufshcd_print_host_regs(hba);
+ ufshcd_print_tmrs(hba, hba->outstanding_tasks);
+ ufshcd_print_trs(hba, hba->outstanding_reqs, pr_prdt);
+ spin_lock_irqsave(hba->host->host_lock, flags);
+ }
+
/*
* if host reset is required then skip clearing the pending
* transfers forcefully because they will get cleared during
@@ -5900,22 +5915,6 @@ static irqreturn_t ufshcd_check_errors(struct
ufs_hba *hba)
/* block commands from scsi mid-layer */
ufshcd_scsi_block_requests(hba);
-
- /* dump controller state before resetting */
- if (hba->saved_err & (INT_FATAL_ERRORS | UIC_ERROR)) {
- bool pr_prdt = !!(hba->saved_err &
- SYSTEM_BUS_FATAL_ERROR);
-
- dev_err(hba->dev, "%s: saved_err 0x%x saved_uic_err 0x%x\n",
- __func__, hba->saved_err,
- hba->saved_uic_err);
-
- ufshcd_print_host_regs(hba);
- ufshcd_print_pwr_info(hba);
How about keep the above prints and move the tmrs and trs to eh?
Sometimes in system instability, the eh may not get a chance to run
even. Still the above prints would provide some clues.
Here is the IRQ handler, ufshcd_print_host_regs() is sometime heavy
enough to cause stability issues during my fault injection test, since
it prints host regs, reg's history, crypto debug infos plus prints
from vops_dump.
How about just printing host regs and reg history here? Most time, these
infos are enough.
Thanks,
Can Guo.
- ufshcd_print_tmrs(hba, hba->outstanding_tasks);
- ufshcd_print_trs(hba, hba->outstanding_reqs,
- pr_prdt);
- }
ufshcd_schedule_eh_work(hba);
retval |= IRQ_HANDLED;
}
