On 03/07/2020 14:01, Hannes Reinecke wrote:
Quite some drivers are using management commands internally, which
typically use the same hardware tag pool (ie they are being allocated
from the same hardware resources) as the 'normal' I/O commands.
These commands are set aside before allocating the block-mq tag bitmap,
so they'll never show up as busy in the tag map.
The block-layer, OTOH, already has 'reserved_tags' to handle precisely
this situation.
So this patch adds a new field 'nr_reserved_cmds' to the SCSI host
template to instruct the block layer to set aside a tag space for these
management commands by using reserved tags.
Apart from (a good few) comments:
Reviewed-by: John Garry <john.garry@xxxxxxxxxx>
Signed-off-by: Hannes Reinecke <hare@xxxxxxx> > ---
drivers/scsi/hosts.c | 3 +++
drivers/scsi/scsi_lib.c | 10 +++++++++-
include/scsi/scsi_host.h | 22 +++++++++++++++++++++-
3 files changed, 33 insertions(+), 2 deletions(-)
diff --git a/drivers/scsi/hosts.c b/drivers/scsi/hosts.c
index 7ec91c3a66ca..db91b045a4ce 100644
--- a/drivers/scsi/hosts.c
+++ b/drivers/scsi/hosts.c
@@ -466,6 +466,9 @@ struct Scsi_Host *scsi_host_alloc(struct scsi_host_template *sht, int privsize)
if (sht->virt_boundary_mask)
shost->virt_boundary_mask = sht->virt_boundary_mask;
+ if (sht->nr_reserved_cmds)
+ shost->nr_reserved_cmds = sht->nr_reserved_cmds;
+
device_initialize(&shost->shost_gendev);
dev_set_name(&shost->shost_gendev, "host%d", shost->host_no);
shost->shost_gendev.bus = &scsi_bus_type;
diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c
index 1d5c1b9a1203..1362f4f17dfd 100644
--- a/drivers/scsi/scsi_lib.c
+++ b/drivers/scsi/scsi_lib.c
@@ -1887,7 +1887,9 @@ int scsi_mq_setup_tags(struct Scsi_Host *shost)
else
tag_set->ops = &scsi_mq_ops_no_commit;
tag_set->nr_hw_queues = shost->nr_hw_queues ? : 1;
- tag_set->queue_depth = shost->can_queue;
+ tag_set->queue_depth =
+ shost->can_queue + shost->nr_reserved_cmds;
I think that this can fit on a single line without exceeding 80 characters
+ tag_set->reserved_tags = shost->nr_reserved_cmds;
tag_set->cmd_size = cmd_size;
tag_set->numa_node = NUMA_NO_NODE;
tag_set->flags = BLK_MQ_F_SHOULD_MERGE;
@@ -1910,6 +1912,9 @@ void scsi_mq_destroy_tags(struct Scsi_Host *shost)
* @op_flags: request allocation flags
*
* Allocates a SCSI command for internal LLDD use.
+ * If 'nr_reserved_commands' is spectified by the host the
again, please check spellings
+ * command will be allocated from the reserved tag pool;
+ * otherwise the normal tag pool will be used.
*/
struct scsi_cmnd *scsi_get_internal_cmd(struct scsi_device *sdev,
enum dma_data_direction data_direction, int op_flags)
@@ -1919,6 +1924,9 @@ struct scsi_cmnd *scsi_get_internal_cmd(struct scsi_device *sdev,
blk_mq_req_flags_t flags = 0;
unsigned int op = REQ_INTERNAL | op_flags;
+ if (sdev->host->nr_reserved_cmds)
+ flags = BLK_MQ_REQ_RESERVED;
Previously I mentioned that '|=' is nicer - not sure if it was missed or
dismissed, so mentioning it again just in case
+
op |= (data_direction == DMA_TO_DEVICE) ?
REQ_OP_SCSI_OUT : REQ_OP_SCSI_IN;
rq = blk_mq_alloc_request(sdev->request_queue, op, flags);
diff --git a/include/scsi/scsi_host.h b/include/scsi/scsi_host.h
index 4919a66565d6..c4d0d26c880e 100644
--- a/include/scsi/scsi_host.h
+++ b/include/scsi/scsi_host.h
@@ -342,10 +342,19 @@ struct scsi_host_template {
/*
* This determines if we will use a non-interrupt driven
* or an interrupt driven scheme. It is set to the maximum number
- * of simultaneous commands a single hw queue in HBA will accept.
+ * of simultaneous commands a single hw queue in HBA will accept
+ * excluding internal commands.
*/
int can_queue;
+ /*
+ * This determines how many commands the HBA will set aside
+ * for internal commands. This number will be added to
+ * @can_queue to calcumate the maximum number of simultaneous
check spelling of calculate
+ * commands sent to the host.
+ */
+ int nr_reserved_cmds;
We have can_queue file in the scsi_host sysfs folder - I wonder if it is
also worth adding a file for this?
+
/*
