On 4/27/20 1:31 PM, Johannes Thumshirn wrote:
Factor sanity checks for zoned commands from sd_zbc_setup_zone_mgmt_cmnd().
This will help with the introduction of an emulated ZONE_APPEND command.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@xxxxxxx>
Reviewed-by: Christoph Hellwig <hch@xxxxxx>
Reviewed-by: Bart Van Assche <bvanassche@xxxxxxx>
---
drivers/scsi/sd_zbc.c | 36 +++++++++++++++++++++++++-----------
1 file changed, 25 insertions(+), 11 deletions(-)
diff --git a/drivers/scsi/sd_zbc.c b/drivers/scsi/sd_zbc.c
index f45c22b09726..ee156fbf3780 100644
--- a/drivers/scsi/sd_zbc.c
+++ b/drivers/scsi/sd_zbc.c
@@ -209,6 +209,26 @@ int sd_zbc_report_zones(struct gendisk *disk, sector_t sector,
return ret;
}
+static blk_status_t sd_zbc_cmnd_checks(struct scsi_cmnd *cmd)
+{
+ struct request *rq = cmd->request;
+ struct scsi_disk *sdkp = scsi_disk(rq->rq_disk);
+ sector_t sector = blk_rq_pos(rq);
+
+ if (!sd_is_zoned(sdkp))
+ /* Not a zoned device */
+ return BLK_STS_IOERR;
+
+ if (sdkp->device->changed)
+ return BLK_STS_IOERR;
+
+ if (sector & (sd_zbc_zone_sectors(sdkp) - 1))
+ /* Unaligned request */
+ return BLK_STS_IOERR;
+
+ return BLK_STS_OK;
+}
+
/**
* sd_zbc_setup_zone_mgmt_cmnd - Prepare a zone ZBC_OUT command. The operations
* can be RESET WRITE POINTER, OPEN, CLOSE or FINISH.
@@ -223,20 +243,14 @@ blk_status_t sd_zbc_setup_zone_mgmt_cmnd(struct scsi_cmnd *cmd,
unsigned char op, bool all)
{
struct request *rq = cmd->request;
- struct scsi_disk *sdkp = scsi_disk(rq->rq_disk);
sector_t sector = blk_rq_pos(rq);
+ struct scsi_disk *sdkp = scsi_disk(rq->rq_disk);
sector_t block = sectors_to_logical(sdkp->device, sector);
+ blk_status_t ret;
- if (!sd_is_zoned(sdkp))
- /* Not a zoned device */
- return BLK_STS_IOERR;
-
- if (sdkp->device->changed)
- return BLK_STS_IOERR;
-
- if (sector & (sd_zbc_zone_sectors(sdkp) - 1))
- /* Unaligned request */
- return BLK_STS_IOERR;
+ ret = sd_zbc_cmnd_checks(cmd);
+ if (ret != BLK_STS_OK)
+ return ret;
cmd->cmd_len = 16;
memset(cmd->cmnd, 0, cmd->cmd_len);
Reviewed-by: Hannes Reinecke <hare@xxxxxxx>
Cheers,
Hannes
--
Dr. Hannes Reinecke Teamlead Storage & Networking
hare@xxxxxxx +49 911 74053 688
SUSE Software Solutions GmbH, Maxfeldstr. 5, 90409 Nürnberg
HRB 36809 (AG Nürnberg), Geschäftsführer: Felix Imendörffer
