Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
---
Documentation/scsi/index.rst | 1 +
.../scsi/{qlogicfas.txt => qlogicfas.rst} | 17 +++++++++++++----
drivers/scsi/Kconfig | 2 +-
3 files changed, 15 insertions(+), 5 deletions(-)
rename Documentation/scsi/{qlogicfas.txt => qlogicfas.rst} (92%)
diff --git a/Documentation/scsi/index.rst b/Documentation/scsi/index.rst
index 17327f67af68..29e211ee9145 100644
--- a/Documentation/scsi/index.rst
+++ b/Documentation/scsi/index.rst
@@ -30,5 +30,6 @@ Linux SCSI Subsystem
ncr53c8xx
NinjaSCSI
ppa
+ qlogicfas
scsi_transport_srp/figures
diff --git a/Documentation/scsi/qlogicfas.txt b/Documentation/scsi/qlogicfas.rst
similarity index 92%
rename from Documentation/scsi/qlogicfas.txt
rename to Documentation/scsi/qlogicfas.rst
index c211d827fef2..b17f1b3676c3 100644
--- a/Documentation/scsi/qlogicfas.txt
+++ b/Documentation/scsi/qlogicfas.rst
@@ -1,3 +1,8 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=================================
+Qlogic FASXXX Family Driver Notes
+=================================
This driver supports the Qlogic FASXXX family of chips. This driver
only works with the ISA, VLB, and PCMCIA versions of the Qlogic
@@ -16,7 +21,8 @@ is provided by the qla1280 driver.
Nor does it support the PCI-Basic, which is supported by the
'am53c974' driver.
-PCMCIA SUPPORT
+PCMCIA Support
+==============
This currently only works if the card is enabled first from DOS. This
means you will have to load your socket and card services, and
@@ -31,7 +37,8 @@ it from configuring the card.
I am working with the PCMCIA group to make it more flexible, but that
may take a while.
-ALL CARDS
+All Cards
+=========
The top of the qlogic.c file has a number of defines that controls
configuration. As shipped, it provides a balance between speed and
@@ -46,7 +53,8 @@ command or something. It comes up faster if this is set to zero, and
if you have reliable hardware and connections it may be more useful to
not reset things.
-SOME TROUBLESHOOTING TIPS
+Some Troubleshooting Tips
+=========================
Make sure it works properly under DOS. You should also do an initial FDISK
on a new drive if you want partitions.
@@ -54,7 +62,8 @@ on a new drive if you want partitions.
Don't enable all the speedups first. If anything is wrong, they will make
any problem worse.
-IMPORTANT
+Important
+=========
The best way to test if your cables, termination, etc. are good is to
copy a very big file (e.g. a doublespace container file, or a very
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 82462d6a4ce5..d34c682e94cf 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1117,7 +1117,7 @@ config SCSI_QLOGIC_FAS
SCSI support"), below.
Information about this driver is contained in
- <file:Documentation/scsi/qlogicfas.txt>. You should also read the
+ <file:Documentation/scsi/qlogicfas.rst>. You should also read the
SCSI-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
--
2.21.1
