On Tue, Aug 13, 2019 at 6:48 AM Damien Le Moal <Damien.LeMoal@xxxxxxx> wrote: > > On 2019/08/12 19:12, Martin K. Petersen wrote: > > > > Justin, > > > >>> Attached 2 x brand new Western Digital 8TB USB 3.0 drives awhile back > >>> and ran some file copy tests and was getting these warnings-- is > >>> there any way to avoid these warnings? I did confirm with parted > >>> that the partition was aligned but this appears to be something > >>> related to the firmware on the device according to [1] and [2]? > > > >> sg_vpd_bdc.txt > >> Block device characteristics VPD page (SBC): > >> Nominal rotation rate: 5400 rpm > >> Product type: Not specified > >> WABEREQ=0 > >> WACEREQ=0 > >> Nominal form factor: 3.5 inch > >> ZONED=0 > > > > Damien: What can we do to limit the messages in cases like this? Would > > it make sense to make the residual warning conditional on sd_is_zoned()? > > > > Justin, > > Can you send the output of "lsscsi" for these drives ? I need the exact disk > model ref name and FW version to see if there is an update for this problem, if > it is a known one. If it is not, I will signal it and get a fix started. > Requested lsscsi output: [7:0:0:0] disk WD My Book 25EE 4004 /dev/sdf [7:0:0:1] enclosu WD SES Device 4004 - [8:0:0:0] disk WD My Book 25EE 4004 /dev/sdg [8:0:0:1] enclosu WD SES Device 4004 - Host: scsi7 Channel: 00 Target: 00 Lun: 00 Vendor: WD Model: My Book 25EE Rev: 4004 Type: Direct-Access ANSI SCSI revision: 06 Host: scsi7 Channel: 00 Target: 00 Lun: 01 Vendor: WD Model: SES Device Rev: 4004 Type: Enclosure ANSI SCSI revision: 06 Host: scsi8 Channel: 00 Target: 00 Lun: 00 Vendor: WD Model: My Book 25EE Rev: 4004 Type: Direct-Access ANSI SCSI revision: 06 Host: scsi8 Channel: 00 Target: 00 Lun: 01 Vendor: WD Model: SES Device Rev: 4004 Type: Enclosure ANSI SCSI revision: 06 [7:0:0:0] disk WD My Book 25EE 4004 /dev/sdf state=running queue_depth=1 scsi_level=7 type=0 device_blocked=0 timeout=30 [7:0:0:1] enclosu WD SES Device 4004 - state=running queue_depth=1 scsi_level=7 type=13 device_blocked=0 timeout=30 [8:0:0:0] disk WD My Book 25EE 4004 /dev/sdg state=running queue_depth=1 scsi_level=7 type=0 device_blocked=0 timeout=30 [8:0:0:1] enclosu WD SES Device 4004 - state=running queue_depth=1 scsi_level=7 type=13 device_blocked=0 timeout=30 [7:0:0:0] disk none /dev/sdf [7:0:0:1] enclosu 5000cca252e63312 - [8:0:0:0] disk none /dev/sdg [8:0:0:1] enclosu 5000cca252e6a2f9 - [7:0:0:0] disk WD My Book 25EE 4004 /dev/sdf 8.00TB [7:0:0:1] enclosu WD SES Device 4004 - - [8:0:0:0] disk WD My Book 25EE 4004 /dev/sdg 8.00TB [8:0:0:1] enclosu WD SES Device 4004 - - [7:0:0:0] disk usb:1-1.2:1.0 /dev/sdf [7:0:0:1] enclosu usb:1-1.2:1.0 - [8:0:0:0] disk usb:1-1.1:1.0 /dev/sdg [8:0:0:1] enclosu usb:1-1.1:1.0 - # smartctl -a /dev/sdg /dev/sdg: Unknown USB bridge [0x1058:0x25ee (0x4004)] # smartctl -a /dev/sdf /dev/sdf: Unknown USB bridge [0x1058:0x25ee (0x4004)] Regards, Justin.
