On 06/02/2019 16:27, Alim Akhtar wrote: > On 06/02/19 8:29 PM, Marc Gonzalez wrote: > >> [ 2.405734] regulator_disable: ENTER vdd_l26 >> [ 2.405958] regulator_disable: EXIT vdd_l26 >> [ 2.406032] regulator_set_load: vdd_l26 = 0 uA >> [ 3.930447] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11 >> [ 5.434358] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11 >> [ 6.938318] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11 >> [ 6.938414] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr_retry: query attribute, idn 13, failed with error -11 after 3 retires >> [ 6.946959] ufshcd-qcom 1da4000.ufshc: ufshcd_disable_auto_bkops: failed to enable exception event -11 >> [ 6.958523] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id 0x1587 failed 3 retries >> [ 6.967730] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id 0x1586 failed 3 retries >> [ 6.975576] ufshcd-qcom 1da4000.ufshc: ufshcd_get_max_pwr_mode: invalid max pwm tx gear read = 0 >> [ 6.983306] ufshcd-qcom 1da4000.ufshc: ufshcd_probe_hba: Failed getting max supported power mode >> [ 8.506314] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11 >> [ 10.010352] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11 >> [ 11.514313] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11 >> [ 11.514412] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag_retry: query attribute, opcode 5, idn 3, failed with error -11 after 3 retires >> [ 13.050354] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11 >> [ 14.554313] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11 >> [ 16.058313] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11 >> [ 16.058421] ufshcd-qcom 1da4000.ufshc: ufshcd_read_desc_param: Failed reading descriptor. desc_id 8, desc_index 0, param_offset 0, ret -11 >> [ 16.067654] ufshcd-qcom 1da4000.ufshc: ufshcd_init_icc_levels: Failed reading power descriptor.len = 98 ret = -11 >> [ 37.074334] ufshcd-qcom 1da4000.ufshc: link startup failed 1 > > Can you check if your UFS device RESET_N is asserted correctly. It might > be connected to some regulator and may be you can try keeping that > regulator as "regulator-always-on" from your DT node. How do I check RESET_N? In software or hardware? Do you think it is not a good idea to revert 60f0187031c05e04cbadffb62f557d0ff3564490 ? Regards.
