> Older Controller might not support volume status, so disable
> it if 'hpsa_allow_any' is present.
It makes my DL380G4 boot with hpsa.hpsa_allow_any=1 and it seems to
work. Howevere, there are multiole verbose dmesg entries about failing
things:
0.267224] HP HPSA Driver (v 3.4.18-0)
[ 0.267351] hpsa 0000:04:03.0: unsupported board ID: 0x40910e11
[ 0.267494] hpsa 0000:04:03.0: unsupported board ID: 0x40910e11
[ 0.267695] hpsa 0000:04:03.0: PCI IRQ 51 -> rerouted to legacy IRQ 19
[ 0.267889] hpsa 0000:04:03.0: Physical aborts not supported
[ 0.268036] hpsa 0000:04:03.0: Logical aborts not supported
[ 0.268163] hpsa 0000:04:03.0: HP SSD Smart Path aborts not supported
[ 0.448240] scsi host0: hpsa
[ 0.452228] hpsa 0000:04:03.0: report luns requested format 2, got 0
[ 0.453950] hpsa 0000:04:03.0: hpsa0: hpsa_update_device_info: can't get device id for host 0:C0:T0:L0 Direct-Access MAN3735MC
[ 0.454312] hpsa 0000:04:03.0: SCSI status: LUN:0000000000000000 CDB:26000000000015000801000000000000
[ 0.454525] hpsa 0000:04:03.0: SCSI Status = 02, Sense key = 0x05, ASC = 0x3a, ASCQ = 0x00
[ 0.458100] hpsa 0000:04:03.0: hpsa0: hpsa_update_device_info: can't get device id for host 0:C0:T-1:L-1 Direct-Access MAP3735NC
[ 0.458453] hpsa 0000:04:03.0: SCSI status: LUN:0000000000000000 CDB:26000100000015000801000000000000
[ 0.458668] hpsa 0000:04:03.0: SCSI Status = 02, Sense key = 0x05, ASC = 0x3a, ASCQ = 0x00
[ 0.485980] hpsa 0000:04:03.0: C0:T-1:L-1 Volume status not available, assuming online.
[ 0.486807] hpsa 0000:04:03.0: scsi 0:0:0:0: masked Direct-Access FUJITSU MAN3735MC PHYS DRV SSDSmartPathCap- En- Exp=0
[ 0.487020] hpsa 0000:04:03.0: scsi 0:0:1:0: masked Direct-Access FUJITSU MAP3735NC PHYS DRV SSDSmartPathCap- En- Exp=0
[ 0.487229] hpsa 0000:04:03.0: scsi 0:1:0:0: added Direct-Access HP LOGICAL VOLUME RAID-1(+0) SSDSmartPathCap- En- Exp=1
[ 0.487440] hpsa 0000:04:03.0: scsi 0:3:0:0: added RAID HP SA6i controller SSDSmartPathCap- En- Exp=1
[ 0.487997] scsi 0:1:0:0: Direct-Access HP LOGICAL VOLUME 2.84 PQ: 0 ANSI: 4
[ 0.488989] scsi 0:3:0:0: RAID HP SA6i 2.84 PQ: 0 ANSI: 0
[ 0.489390] hpsa 0000:0b:04.0: unsupported board ID: 0x409c0e11
[ 0.489532] hpsa 0000:0b:04.0: unsupported board ID: 0x409c0e11
[ 0.489870] hpsa 0000:0b:04.0: Physical aborts not supported
[ 0.489995] hpsa 0000:0b:04.0: Logical aborts not supported
[ 0.490118] hpsa 0000:0b:04.0: HP SSD Smart Path aborts not supported
[ 0.628221] scsi host1: hpsa
[ 0.632143] hpsa 0000:0b:04.0: report luns requested format 2, got 0
[ 0.633498] hpsa 0000:0b:04.0: scsi 1:3:0:0: added RAID HP SA6400 controller SSDSmartPathCap- En- Exp=1
[ 0.634246] scsi 1:0:0:0: RAID HP SA6400 2.84 PQ: 0 ANSI: 0
[ 0.634882] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[ 0.635581] sd 0:1:0:0: [sda] 430622325 512-byte logical blocks: (220 GB/205 GiB)
[ 0.635974] sd 0:1:0:0: [sda] Write Protect is off
[ 0.636118] sd 0:1:0:0: [sda] Mode Sense: 5b 00 00 08
[ 0.636337] sd 0:1:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Among these, the following show up red in dmesg:
report luns requested format 2, got 0
hpsa0: hpsa_update_device_info: can't get device id for host 0:C0:T0:L0 Direct-Access MAN3735MC
hpsa0: hpsa_update_device_info: can't get device id for host 0:C0:T-1:L-1 Direct-Access MAP3735NC
report luns requested format 2, got 0
--
Meelis Roos (mroos@xxxxxxxx)
