Bu Tao,
One other issue: the 'sender' of your patchset is "butao". For
upstreaming purpose, it is recommended to use your full name, in
"first name" + "Surname" format. In your case, you need to specify it
in your commit message:
$ git commit --amend --author="Bu Tao <butao@xxxxxxxxxxxxx>"
You may also want to add that to your .gitconfig to save your future effort.
[user]
name = Bu Tao
email = butao@xxxxxxxxxxxxx
-Guodong
On Sat, Jun 10, 2017 at 10:44 AM, Guodong Xu <guodong.xu@xxxxxxxxxx> wrote:
> Bu Tao,
>
> 1. Subject line of this patch goes something like "arm64: dts: hi3660:
> add ufs support xxx"
>
> 2. Have you run "./scripts/get_maintainer.pl *.patch" to get the
> correct maintainers to include into your patch review?
> I don't think so. Because this is a dts change, however in your
> email's to/ cc/, there is no DTS reviewers being included. Please fix
> that and resend.
>
> 3. I suppose before sending your patchset, you already tested it
> against tip kernel. For example, where your dts change can be applied?
> If they apply to my dts patchset [1], please mention it in your commit
> message. If they don't, then please tell us where.
>
> [1]. http://www.spinics.net/lists/devicetree/msg178303.html
>
> 4. Re-send, send them as "git format-patch -v2".
>
> -Guodong
>
> On Sat, Jun 10, 2017 at 9:20 AM, butao <butao@xxxxxxxxxxxxx> wrote:
>> add ufs node for hi3660
>>
>> Signed-off-by: Bu Tao <butao@xxxxxxxxxxxxx>
>> ---
>> arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 20 ++++++++++++++++++++
>> 1 file changed, 20 insertions(+)
>> mode change 100644 => 100755 arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>>
>> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> old mode 100644
>> new mode 100755
>> index 3983086bd67b..4ba9cec43d94
>> --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> @@ -141,6 +141,26 @@
>> #size-cells = <2>;
>> ranges;
>>
>> + ufs: ufs@ff3b0000 {
>> + compatible = "jedec,ufs-1.1", "hisilicon,hi3660-ufs";
>> + reg = <0x0 0xff3b0000 0x0 0x1000>, /* 0: HCI standard */
>> + <0x0 0xff3b1000 0x0 0x1000>; /* 1: UFS SYS CTRL */
>> + interrupt-parent = <&gic>;
>> + interrupts = <0 278 4>;
>> + clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>,
>> + <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>;
>> + clock-names = "clk_ref", "clk_phy";
>> + freq-table-hz = <0 0>, <0 0>;
>> + resets = <&crg_rst 0x84 12>, /* offset: 0x84; bit: 12 */
>> + <&crg_rst 0x84 7>; /* offset: 0x84; bit: 7 */
>> + reset-names = "rst", "assert";
>> + ufs-hi3660-use-rate-B;
>> + ufs-hi3660-broken-fastauto;
>> + ufs-hi3660-use-HS-GEAR3;
>> + ufs-hi3660-broken-clk-gate-bypass;
>> + status = "ok";
>> + };
>> +
>> fixed_uart5: fixed_19_2M {
>> compatible = "fixed-clock";
>> #clock-cells = <0>;
>> --
>> 2.11.GIT
>>
