From: Damien Le Moal <damien.lemoal@xxxxxxx>
Resetting a zone write pointer is equivalent to discarding sectors:
after a reset, the zone sectors will contain zeros (or the format
pattern). So there is no need for mutual exclusion between a zone reset
and write. Similarly to discard, make it the responsability of the user
to properly synchronize between reset and write (as is done now for
discard and write).
Signed-off-by: Damien Le Moal <damien.lemoal@xxxxxxx>
---
drivers/scsi/sd_zbc.c | 42 ++++++++++++++++--------------------------
1 file changed, 16 insertions(+), 26 deletions(-)
diff --git a/drivers/scsi/sd_zbc.c b/drivers/scsi/sd_zbc.c
index 29ba1d7..fcf0fad 100644
--- a/drivers/scsi/sd_zbc.c
+++ b/drivers/scsi/sd_zbc.c
@@ -237,7 +237,6 @@ int sd_zbc_setup_reset_cmnd(struct scsi_cmnd *cmd)
struct scsi_disk *sdkp = scsi_disk(rq->rq_disk);
sector_t sector = blk_rq_pos(rq);
sector_t block = sectors_to_logical(sdkp->device, sector);
- unsigned int zno = block >> sdkp->zone_shift;
if (!sd_is_zoned(sdkp))
/* Not a zoned device */
@@ -250,11 +249,6 @@ int sd_zbc_setup_reset_cmnd(struct scsi_cmnd *cmd)
/* Unaligned request */
return BLKPREP_KILL;
- /* Do not allow concurrent reset and writes */
- if (sdkp->zones_wlock &&
- test_and_set_bit(zno, sdkp->zones_wlock))
- return BLKPREP_DEFER;
-
cmd->cmd_len = 16;
memset(cmd->cmnd, 0, cmd->cmd_len);
cmd->cmnd[0] = ZBC_OUT;
@@ -324,38 +318,34 @@ void sd_zbc_complete(struct scsi_cmnd *cmd,
struct request *rq = cmd->request;
switch (req_op(rq)) {
+ case REQ_OP_ZONE_RESET:
+
+ if (result &&
+ sshdr->sense_key == ILLEGAL_REQUEST &&
+ sshdr->asc == 0x24)
+ /*
+ * INVALID FIELD IN CDB error: reset of a conventional
+ * zone was attempted. Nothing to worry about, so be
+ * quiet about the error.
+ */
+ rq->rq_flags |= RQF_QUIET;
+ break;
+
case REQ_OP_WRITE:
case REQ_OP_WRITE_SAME:
- case REQ_OP_ZONE_RESET:
/* Unlock the zone */
sd_zbc_write_unlock_zone(cmd);
- if (!result ||
- sshdr->sense_key != ILLEGAL_REQUEST)
- break;
-
- switch (sshdr->asc) {
- case 0x24:
- /*
- * INVALID FIELD IN CDB error: For a zone reset,
- * this means that a reset of a conventional
- * zone was attempted. Nothing to worry about in
- * this case, so be quiet about the error.
- */
- if (req_op(rq) == REQ_OP_ZONE_RESET)
- rq->rq_flags |= RQF_QUIET;
- break;
- case 0x21:
+ if (result &&
+ sshdr->sense_key == ILLEGAL_REQUEST &&
+ sshdr->asc == 0x21)
/*
* INVALID ADDRESS FOR WRITE error: It is unlikely that
* retrying write requests failed with any kind of
* alignement error will result in success. So don't.
*/
cmd->allowed = 0;
- break;
- }
-
break;
case REQ_OP_ZONE_REPORT:
--
2.9.3
