Douglas Gilbert wrote:
Changelog:
- make existing libata VPD device identification page (0x83)
supply the ATA serial number in the libata "vendor
specific" designator (from Chris Paulson-Ellis)
- add a "t10 vendor id based" designator as defined in
SAT rev 07a (section 10.3.4.2.3) that supplies ATA
model and serial numbers
- make the libata VPD page 0x83 more extensible (for
adding more designators in the future).
Signed-off-by: Douglas Gilbert <dougg@xxxxxxxxxx>
------------------------------------------------------------------------
--- linux/drivers/scsi/libata-scsi.c 2006-01-04 08:50:42.000000000 +1000
+++ linux/drivers/scsi/libata-scsi.c2615vpd 2006-01-06 20:16:25.000000000 +1000
@@ -1532,16 +1532,16 @@
return 0;
}
-static const char *inq_83_str = "Linux ATA-SCSI simulator";
-
/**
* ata_scsiop_inq_83 - Simulate INQUIRY EVPD page 83, device identity
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
* @buflen: Response buffer length.
*
- * Returns device identification. Currently hardcoded to
- * return "Linux ATA-SCSI simulator".
+ * Yields two logocal unit device identification designators:
+ * - vendor specific ASCII containing the ATA serial number
+ * - SAT defined "t10 vendor id based" containing ASCII vendor
+ * name ("ATA "), model and serial numbers.
*
* LOCKING:
* spin_lock_irqsave(host_set lock)
@@ -1550,16 +1550,39 @@
unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf,
unsigned int buflen)
{
+ int num;
+ const int sat_model_serial_desc_len = 68;
+ const int ata_model_byte_len = 40;
+
rbuf[1] = 0x83; /* this page code */
- rbuf[3] = 4 + strlen(inq_83_str); /* page len */
+ num = 4;
- /* our one and only identification descriptor (vendor-specific) */
- if (buflen > (strlen(inq_83_str) + 4 + 4 - 1)) {
- rbuf[4 + 0] = 2; /* code set: ASCII */
- rbuf[4 + 3] = strlen(inq_83_str);
- memcpy(rbuf + 4 + 4, inq_83_str, strlen(inq_83_str));
+ if (buflen > (ATA_SERNO_LEN + num + 3)) {
+ /* piv=0, assoc=lu, code_set=ACSII, designator=vendor */
+ rbuf[num + 0] = 2;
+ rbuf[num + 3] = ATA_SERNO_LEN;
+ num += 4;
+ ata_dev_id_string(args->id, (unsigned char *) rbuf + num,
+ ATA_ID_SERNO_OFS, ATA_SERNO_LEN);
+ num += ATA_SERNO_LEN;
}
-
+ if (buflen > (sat_model_serial_desc_len + num + 3)) {
+ /* SAT defined lu model and serial numbers descriptor */
+ /* piv=0, assoc=lu, code_set=ACSII, designator=t10 vendor id */
+ rbuf[num + 0] = 2;
+ rbuf[num + 1] = 1;
+ rbuf[num + 3] = sat_model_serial_desc_len;
+ num += 4;
+ strncpy(rbuf + num, "ATA ", 8);
+ num += 8;
+ ata_dev_id_string(args->id, (unsigned char *) rbuf + num,
+ ATA_ID_PROD_OFS, ata_model_byte_len);
+ num += ata_model_byte_len;
+ ata_dev_id_string(args->id, (unsigned char *) rbuf + num,
+ ATA_ID_SERNO_OFS, ATA_SERNO_LEN);
+ num += ATA_SERNO_LEN;
+ }
+ rbuf[3] = num - 4; /* page len (assume less than 256 bytes) */
return 0;
This removes the identifier that has existed since libata was created,
which could break something.
At the very least, update the existing code to indicate assoc=port, and
then append the other descriptor data you wish to add after that.
Jeff
-
: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
