I've been working on a problem with Promise 20269 PATA adapter under LibATA
that if I attach a CDROM drive, I can not see the drive. The message log
reports that the driver sees the device, but when I'm fully booted, there's
no device available. If I attach it to the motherboard IDE bus, I can
access it just fine. I've attached a copy of the boot log and you'll see
the motherboard CD/DVD and the one attached to the Promise. I suspect the
PDC driver isn't handling the CDrom. I'm currently running 2.6.15.
Best wishes,
John Treubig
VT Miltope
[ 73.368469] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 73.369256] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing disabled
[ 73.370635] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 73.371770] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 73.373119] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 73.398283] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 73.423414] parport: PnPBIOS parport detected.
[ 73.448207] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
[ 73.473924] lp0: using parport0 (interrupt-driven).
[ 73.499714] Floppy drive(s): fd0 is 1.44M
[ 73.539432] FDC 0 is a post-1991 82077
[ 73.566083] loop: loaded (max 8 devices)
[ 73.591948] r8169 Gigabit Ethernet driver 2.2LK loaded
[ 73.618331] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 73.644798] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC1] -> GSI 16
(level, high) -> IRQ 16
[ 73.673058] eth0: Identified chip type is 'RTL8169s/8110s'.
[ 73.673063] eth0: RTL8169 at 0xd080e000, 00:0d:61:7a:f8:1b, IRQ 16
[ 73.761222] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 73.788587] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 73.816777] NFORCE2: IDE controller at PCI slot 0000:00:09.0
[ 73.845240] NFORCE2: chipset revision 162
[ 73.873659] NFORCE2: not 100% native mode: will probe irqs later
[ 73.902703] NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
[ 73.931482] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA,
hdb:DMA
[ 73.960485] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA,
hdd:DMA
[ 73.988760] Probing IDE interface ide0...
[ 74.251811] hda: TOSHIBA MK4019GAX, ATA DISK drive
[ 74.890885] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 74.919036] Probing IDE interface ide1...
[ 75.589842] hdc: DVD-ROM DDU1621, ATAPI CD/DVD-ROM drive
[ 75.923408] ide1 at 0x170-0x177,0x376 on irq 15
[ 75.951996] hda: max request size: 128KiB
[ 76.684039] hda: Host Protected Area detected.
[ 76.684040] current capacity is 78138047 sectors (40006 MB)
[ 76.684042] native capacity is 78140160 sectors (40007 MB)
[ 76.767722] hda: Host Protected Area disabled.
[ 76.795182] hda: 78140160 sectors (40007 MB), CHS=65535/16/63, UDMA(33)
[ 76.823136] hda: cache flushes supported
[ 76.851214] hda: hda1 hda2 hda3
[ 76.885378] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 76.913692] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19
(level, high) -> IRQ 17
[ 77.152568] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 77.152570] <Adaptec 29160 Ultra160 SCSI adapter>
[ 77.152571] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253
SCBs
[ 77.152573]
[ 93.666571] Vendor: QUANTUM Model: ATLAS_V_36_SCA Rev: 0230
[ 93.696930] Type: Direct-Access ANSI SCSI
revision: 03
[ 93.726541] scsi0:A:6:0: Tagged Queuing enabled. Depth 32
[ 93.755805] target0:0:6: Beginning Domain Validation
[ 93.787494] target0:0:6: wide asynchronous.
[ 93.818348] target0:0:6: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns,
offset 63)
[ 93.853396] target0:0:6: Ending Domain Validation
[ 95.932410] QLogic Fibre Channel HBA Driver
[ 95.962527] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 95.992427] ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17
(level, high) -> IRQ 18
[ 96.023111] qla2100 0000:01:09.0: Found an ISP2100, irq 18, iobase
0xd0812000
[ 96.054892] qla2100 0000:01:09.0: Configuring PCI space...
[ 96.086038] qla2100 0000:01:09.0: Configure NVRAM parameters...
[ 96.202033] qla2100 0000:01:09.0: Verifying loaded RISC code...
[ 96.395548] qla2100 0000:01:09.0: Waiting for LIP to complete...
[ 116.712015] qla2100 0000:01:09.0: Cable is unplugged...
[ 116.741540] scsi1 : qla2xxx
[ 116.770559] qla2100 0000:01:09.0:
[ 116.770560] QLogic Fibre Channel HBA Driver: 8.01.03-k
[ 116.770561] QLogic QLA2100 -
[ 116.770562] ISP2100: PCI (33 MHz) @ 0000:01:09.0 hdma-, host#=1,
fw=1.19.25 TP
[ 116.883207] ide-scsi is deprecated for cd burning! Use ide-cd and give
dev=/dev/hdX as device
[ 116.912530] scsi2 : SCSI host adapter emulation for IDE ATAPI devices
[ 116.941982] Vendor: SONY Model: DVD-ROM DDU1621 Rev: S3.5
[ 116.972660] Type: CD-ROM ANSI SCSI
revision: 00
[ 117.002592] libata version 1.20 loaded.
[ 117.002623] pata_pdc2027x 0000:01:08.0: version 0.73
[ 117.002648] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16
(level, high) -> IRQ 16
[ 117.033294] pdc_read_counter: bccrh [7C05] bccrl [7E38]
[ 117.063738] pdc_read_counter: bccrhv[7C05] bccrlv[7E38]
[ 117.093641] pdc_detect_pll_input_clock: scr[40E20]
[ 117.223544] pdc_read_counter: bccrh [7BD2] bccrl [7A41]
[ 117.253592] pdc_read_counter: bccrhv[7BD2] bccrlv[7A1A]
[ 117.283101] pdc_detect_pll_input_clock: scr[44E20]
[ 117.312919] pdc_detect_pll_input_clock: start[1040383544] end[1038711361]
[ 117.342897] pdc_detect_pll_input_clock: PLL input clock[16721830]Hz
[ 117.372497] pata_pdc2027x 0000:01:08.0: PLL input clock 16721 kHz
[ 117.401788] pdc_adjust_pll: pout_required is 133333333
[ 117.431253] pdc_adjust_pll: pll_ctl[D58]
[ 117.460259] pdc_adjust_pll: F[117] R[13] ratio*1000[7974]
[ 117.489060] pdc_adjust_pll: Writing pll_ctl[D75]
[ 117.547079] pdc_adjust_pll: pll_ctl[D75]
[ 117.574619] ata1: PATA max UDMA/133 cmd 0xD08197C0 ctl 0xD0819FDA bmdma
0xD0819000 irq 16
[ 117.603113] ata2: PATA max UDMA/133 cmd 0xD08195C0 ctl 0xD0819DDA bmdma
0xD0819008 irq 16
[ 117.631054] pdc2027x_cbl_detect: No cable or 80-conductor cable on port 0
[ 117.963877] ata1: dev 1 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000
86:0000 87:0000 88:0407
[ 117.963880] ata1: dev 1 ATAPI, max UDMA/33
[ 117.991560] pdc2027x_set_piomode: adev->pio_mode[C]
[ 118.019059] pdc2027x_set_piomode: Set pio regs...
[ 118.046224] pdc2027x_set_piomode: Set pio regs done
[ 118.073102] pdc2027x_set_piomode: Set to pio mode[4]
[ 118.099550] pdc2027x_set_dmamode: Set udma regs...
[ 118.125576] pdc2027x_set_dmamode: Set udma regs done
[ 118.151159] pdc2027x_set_dmamode: Set to udma mode[2]
[ 118.176467] ata1: dev 1 configured for UDMA/33
[ 118.201415] pdc2027x_set_piomode: adev->pio_mode[C]
[ 118.225873] pdc2027x_set_piomode: Set pio regs...
[ 118.250009] pdc2027x_set_piomode: Set pio regs done
[ 118.273955] pdc2027x_set_piomode: Set to pio mode[4]
[ 118.297779] pdc2027x_set_dmamode: Set udma regs...
[ 118.321415] pdc2027x_set_dmamode: Set udma regs done
[ 118.344714] pdc2027x_set_dmamode: Set to udma mode[2]
[ 118.367700] scsi3 : pata_pdc2027x
[ 118.390701] pdc2027x_cbl_detect: No cable or 80-conductor cable on port 1
[ 118.574623] ATA: abnormal status 0x8 on port 0xD08195DF
[ 118.598326] ata2: disabling port
[ 118.621489] scsi4 : pata_pdc2027x
[ 118.643926] ata1(1): WARNING: ATAPI is disabled, device ignored.
[ 118.666412] sata_sil 0000:01:0d.0: version 0.9
[ 118.666686] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 118.689054] ACPI: PCI Interrupt 0000:01:0d.0[A] -> Link [APC3] -> GSI 18
(level, high) -> IRQ 19
[ 118.712067] ata3: SATA max UDMA/100 cmd 0xD0814080 ctl 0xD081408A bmdma
0xD0814000 irq 19
[ 118.734881] ata4: SATA max UDMA/100 cmd 0xD08140C0 ctl 0xD08140CA bmdma
0xD0814008 irq 19
[ 118.956931] ata3: no device found (phy stat 00000000)
[ 118.979151] scsi5 : sata_sil
[ 119.201572] ata4: no device found (phy stat 00000000)
[ 119.223810] scsi6 : sata_sil
[ 119.246507] SCSI device sda: 71722776 512-byte hdwr sectors (36722 MB)
[ 119.271242] SCSI device sda: drive cache: write back
[ 119.294511] SCSI device sda: 71722776 512-byte hdwr sectors (36722 MB)
[ 119.319458] SCSI device sda: drive cache: write back
[ 119.342703] sda: sda1
[ 119.365643] sd 0:0:6:0: Attached scsi disk sda
[ 119.390260] sr0: scsi-1 drive
[ 119.413124] Uniform CD-ROM driver Revision: 3.20
[ 119.436363] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 119.436407] sd 0:0:6:0: Attached scsi generic sg0 type 0
[ 119.460034] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 119.482764] Fusion MPT base driver 3.03.04
[ 119.505782] Copyright (c) 1999-2005 LSI Logic Corporation
[ 119.528651] Fusion MPT SPI Host driver 3.03.04
[ 119.551238] Fusion MPT FC Host driver 3.03.04
[ 119.573627] Fusion MPT SAS Host driver 3.03.04
[ 119.596065] Fusion MPT misc device (ioctl) driver 3.03.04
[ 119.619025] mptctl: Registered with Fusion MPT base driver
[ 119.642394] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 119.666435] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[ 119.690689] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 22
(level, high) -> IRQ 20
[ 119.716056] PCI: Setting latency timer of device 0000:00:02.2 to 64
[ 119.716061] ehci_hcd 0000:00:02.2: EHCI Host Controller
[ 119.741294] ehci_hcd 0000:00:02.2: debug port 1
[ 119.766129] PCI: cache line size of 64 is not supported by device
0000:00:02.2
[ 119.766187] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus
number 1
[ 119.791799] ehci_hcd 0000:00:02.2: irq 20, io mem 0xe0005000
[ 119.817600] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10
Dec 2004
[ 119.844138] hub 1-0:1.0: USB hub found
[ 119.870593] hub 1-0:1.0: 6 ports detected
[ 119.997462] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI)
Driver (PCI)
[ 119.997835] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
[ 120.025134] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21
(level, high) -> IRQ 21
[ 120.053279] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 120.053283] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 120.081161] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus
number 2
[ 120.109126] ohci_hcd 0000:00:02.0: irq 21, io mem 0xe0003000
[ 120.189210] hub 2-0:1.0: USB hub found
[ 120.216954] hub 2-0:1.0: 3 ports detected
[ 120.345277] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
[ 120.372791] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20
(level, high) -> IRQ 22
[ 120.400846] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 120.400850] ohci_hcd 0000:00:02.1: OHCI Host Controller
[ 120.428412] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus
number 3
[ 120.456708] ohci_hcd 0000:00:02.1: irq 22, io mem 0xe0004000
[ 120.536699] hub 3-0:1.0: USB hub found
[ 120.564187] hub 3-0:1.0: 3 ports detected
[ 120.691441] USB Universal Host Controller Interface driver v2.3
[ 120.719125] usbcore: registered new driver usblp
[ 120.746503] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class
driver
[ 120.774538] Initializing USB Mass Storage driver...
[ 120.802508] usbcore: registered new driver usb-storage
[ 120.830479] USB Mass Storage support registered.
[ 120.858452] usbcore: registered new driver usbhid
[ 120.886474] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 120.915021] mice: PS/2 mouse device common for all mice
[ 120.944028] NET: Registered protocol family 2
[ 120.981004] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 121.010636] TCP established hash table entries: 16384 (order: 4, 65536
bytes)
[ 121.040586] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 121.070582] TCP: Hash tables configured (established 16384 bind 16384)
[ 121.100531] TCP reno registered
[ 121.130349] ip_conntrack version 2.4 (2047 buckets, 16376 max) - 212
bytes per conntrack
[ 121.169397] input: AT Translated Set 2 keyboard as /class/input/input0
[ 121.216672] ip_tables: (C) 2000-2002 Netfilter core team
[ 121.289499] ipt_recent v0.3.1: Stephen Frost <sfrost@xxxxxxxxxxx>.
http://snowman.net/projects/ipt_recent/
[ 121.322405] arp_tables: (C) 2002 David S. Miller
[ 121.363396] TCP bic registered
[ 121.395559] NET: Registered protocol family 1
[ 121.427331] NET: Registered protocol family 17
[ 121.458822] Using IPI Shortcut mode
[ 121.712984] input: ImPS/2 Generic Wheel Mouse as /class/input/input1
[ 121.911704] VFS: Mounted root (ext2 filesystem) readonly.
[ 121.943686] Freeing unused kernel memory: 216k freed
[ 126.713867] Adding 1188800k swap on /dev/hda3. Priority:-1 extents:1
across:1188800k
[ 127.066247] radDIO: module license 'unspecified' taints kernel.
[ 127.073618] RAD-DIO driver for NuDAQ PCI-7224 V1.0
[ 127.073623] Developed for Miltope Corp. by Radical Systems, Inc.
[ 127.073625] http://www.radicalsystems.com
[ 127.073627] Copyright (c) 2004, Radical Systems, Inc.
[ 127.073629] All rights reserved.
[ 127.080370] Probing...
[ 127.080391] ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18
(level, high) -> IRQ 19
[ 127.080402] Found Device:
[ 127.080404] Name: 0000:01:06.0
[ 127.080406] InitFlag: 0x7248
[ 127.080407] BusNo: 0x1
[ 127.080409] DevFunc: 0x30
[ 127.080410] LCRBase: 0x7000
[ 127.080412] BaseAddr: 0x7400
[ 127.080413] IRQ No: 0x5
[ 127.150593] sata_promise 0000:01:0a.0: version 1.03
[ 127.150622] ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18
(level, high) -> IRQ 19
[ 127.160906] ata5: SATA max UDMA/133 cmd 0xD086A200 ctl 0xD086A238 bmdma
0x0 irq 19
[ 127.160927] ata6: SATA max UDMA/133 cmd 0xD086A280 ctl 0xD086A2B8 bmdma
0x0 irq 19
[ 127.160949] ata7: SATA max UDMA/133 cmd 0xD086A300 ctl 0xD086A338 bmdma
0x0 irq 19
[ 127.160969] ata8: SATA max UDMA/133 cmd 0xD086A380 ctl 0xD086A3B8 bmdma
0x0 irq 19
[ 127.361569] ata5: no device found (phy stat 00000000)
[ 127.361573] scsi7 : sata_promise
[ 127.827258] ata6: dev 0 cfg 49:2f00 82:346b 83:5b01 84:4003 85:3469
86:1801 87:4003 88:407f
[ 127.827264] ata6: dev 0 ATA-6, max UDMA/133, 234441648 sectors: LBA
[ 127.827268] ata6(0): applying bridge limits
[ 127.827417] ata6: dev 0 configured for UDMA/100
[ 127.827420] scsi8 : sata_promise
[ 128.034583] ata7: no device found (phy stat 00000000)
[ 128.034587] scsi9 : sata_promise
[ 128.241278] ata8: no device found (phy stat 00000000)
[ 128.241283] scsi10 : sata_promise
[ 128.248126] Vendor: ATA Model: ST3120023AS Rev: 3.01
[ 128.248136] Type: Direct-Access ANSI SCSI
revision: 05
[ 128.254990] SCSI device sdb: 234441648 512-byte hdwr sectors (120034 MB)
[ 128.255009] SCSI device sdb: drive cache: write back
[ 128.261823] SCSI device sdb: 234441648 512-byte hdwr sectors (120034 MB)
[ 128.261841] SCSI device sdb: drive cache: write back
[ 128.261845] sdb: unknown partition table
[ 128.276051] sd 8:0:0:0: Attached scsi disk sdb
[ 128.289641] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 128.710768] program scsi_unique_id is using a deprecated SCSI ioctl,
please convert it to SG_IO
[ 128.710985] program scsi_unique_id is using a deprecated SCSI ioctl,
please convert it to SG_IO
[ 128.711298] program scsi_unique_id is using a deprecated SCSI ioctl,
please convert it to SG_IO
[ 128.711519] program scsi_unique_id is using a deprecated SCSI ioctl,
please convert it to SG_IO
[ 128.761180] program scsi_unique_id is using a deprecated SCSI ioctl,
please convert it to SG_IO
[ 128.761219] program scsi_unique_id is using a deprecated SCSI ioctl,
please convert it to SG_IO
[ 128.761257] program scsi_unique_id is using a deprecated SCSI ioctl,
please convert it to SG_IO
[ 128.761284] program scsi_unique_id is using a deprecated SCSI ioctl,
please convert it to SG_IO
[ 129.363382] kjournald starting. Commit interval 5 seconds
[ 129.363459] EXT3 FS on hda1, internal journal
[ 129.363465] EXT3-fs: mounted filesystem with ordered data mode.
[ 141.165353] r8169: eth0: link down
