bugme-daemon@xxxxxxxxxxxxxxxxxxx wrote: > > http://bugzilla.kernel.org/show_bug.cgi?id=6061 > > > > > > ------- Additional Comments From collinm@xxxxxxxxxxxxxxxx 2006-02-12 15:00 ------- > ok it's the info Thanks. scsi problem: this aic79xx machine emits "scsi: unknown opcode 0xfa" sometimes. There's an unpleasant-looking ACPI warning in there as well. Kernel is 2.6.13++. > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 0000000020000000 (usable) > BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) > 512MB LOWMEM available. > On node 0 totalpages: 131072 > DMA zone: 4096 pages, LIFO batch:1 > Normal zone: 126976 pages, LIFO batch:31 > HighMem zone: 0 pages, LIFO batch:1 > DMI 2.3 present. > ACPI: Unable to locate RSDP > Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000) > Built 1 zonelists > Kernel command line: root=/dev/sda6 vga=0x317 selinux=0 resume=/dev/sda9 > splash=silent > bootsplash: silent mode. > Initializing CPU#0 > CPU 0 irqstacks, hard=c03f3000 soft=c03f2000 > PID hash table entries: 4096 (order: 12, 65536 bytes) > Detected 1534.121 MHz processor. > Using tsc for high-res timesource > Console: colour dummy device 80x25 > Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) > Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) > Memory: 513580k/524288k available (2113k kernel code, 10156k reserved, 675k > data, 200k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor mode... Ok. > Calibrating delay using timer specific routine.. 3070.54 BogoMIPS (lpj=1535271) > Security Framework v1.0.0 initialized > SELinux: Disabled at boot. > Mount-cache hash table entries: 512 > CPU: After generic identify, caps: 0383f9ff c1c3f9ff 00000000 00000000 00000000 > 00000000 00000000 > CPU: After vendor identify, caps: 0383f9ff c1c3f9ff 00000000 00000000 00000000 > 00000000 00000000 > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > CPU: L2 Cache: 256K (64 bytes/line) > CPU: After all inits, caps: 0383f9ff c1c3f9ff 00000000 00000020 00000000 > 00000000 00000000 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > mtrr: v2.0 (20020519) > CPU: AMD Athlon(tm) XP 1800+ stepping 02 > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Checking 'hlt' instruction... OK. > checking if image is initramfs... it is > Freeing initrd memory: 1819k freed > NET: Registered protocol family 16 > PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1 > PCI: Using configuration type 1 > ACPI: Subsystem revision 20050408 > ACPI: Interpreter disabled. > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI: disabled > PCI: Probing PCI hardware > PCI: Probing PCI hardware (bus 00) > Boot video device is 0000:01:00.0 > PCI: Using IRQ router default [1106/3074] at 0000:00:11.0 > PCI: IRQ 0 for device 0000:00:11.1 doesn't match PIRQ mask - try > pci=usepirqmask > PCI: Hardcoded IRQ 14 for device 0000:00:11.1 > TC classifier action (bugs to netdev@xxxxxxxxxxxxxxx cc hadi@xxxxxxxxxx) > PCI: Bridge: 0000:00:01.0 > IO window: disabled. > MEM window: dde00000-dfefffff > PREFETCH window: cdb00000-ddcfffff > PCI: Setting latency timer of device 0000:00:01.0 to 64 > apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) > audit: initializing netlink socket (disabled) > audit(1139755236.579:1): initialized > Total HugeTLB memory allocated, 0 > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > Initializing Cryptographic API > vesafb: framebuffer at 0xd0000000, mapped to 0xe0880000, using 6144k, total > 131072k > vesafb: mode is 1024x768x16, linelength=2048, pages=1 > vesafb: protected mode interface info at c000:e910 > vesafb: scrolling: redraw > vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 > bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 76011 > bytes,<6>...found (1024x768, 12703 bytes, v3). > Console: switching to colour frame buffer device 127x44 > fb0: VESA VGA frame buffer device > Real Time Clock Driver v1.12 > PNP: No PS/2 controller found. Probing ports directly. > serio: i8042 AUX port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled > ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered > Floppy drive(s): fd0 is 1.44M > FDC 0 is a post-1991 82077 > RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize > loop: loaded (max 8 devices) > mice: PS/2 mouse device common for all mice > input: PC Speaker > NET: Registered protocol family 2 > IP route cache hash table entries: 32768 (order: 5, 131072 bytes) > TCP established hash table entries: 131072 (order: 8, 1048576 bytes) > TCP bind hash table entries: 65536 (order: 6, 262144 bytes) > TCP: Hash tables configured (established 131072 bind 65536) > TCP reno registered > NET: Registered protocol family 1 > Using IPI Shortcut mode > Freeing unused kernel memory: 200k freed > input: AT Translated Set 2 keyboard on isa0060/serio0 > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > SCSI subsystem initialized > scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 > <Adaptec 3960D Ultra160 SCSI adapter> > aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs > > input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1 > scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 > <Adaptec 3960D Ultra160 SCSI adapter> > aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs > > Vendor: IBM-ESXS Model: MAP3367NP FN Rev: B109 > Type: Direct-Access ANSI SCSI revision: 03 > scsi1:A:2:0: Tagged Queuing enabled. Depth 32 > target1:0:2: Beginning Domain Validation > target1:0:2: wide asynchronous. > target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 127) > target1:0:2: Ending Domain Validation > SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB) > SCSI device sda: drive cache: write back > SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB) > SCSI device sda: drive cache: write back > sda: sda1 < sda5 sda6 sda7 sda8 sda9 > > Attached scsi disk sda at scsi1, channel 0, id 2, lun 0 > Attached scsi generic sg0 at scsi1, channel 0, id 2, lun 0, type 0 > VP_IDE: IDE controller at PCI slot 0000:00:11.1 > PCI: Hardcoded IRQ 14 for device 0000:00:11.1 > PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 14 > VP_IDE: chipset revision 6 > VP_IDE: not 100% native mode: will probe irqs later > VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1 > ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio > ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio > Probing IDE interface ide0... > Probing IDE interface ide1... > hdc: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive > ide1 at 0x170-0x177,0x376 on irq 15 > hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) > Uniform CD-ROM driver Revision: 3.20 > Attempting manual resume > swsusp: Suspend partition has wrong signature? > ReiserFS: sda6: found reiserfs format "3.6" with standard journal > ReiserFS: sda6: using ordered data mode > ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, > max trans len 1024, max batch 900, max commit age 30, max trans age 30 > ReiserFS: sda6: checking transaction log (sda6) > ReiserFS: sda6: Using r5 hash to sort names > bootsplash: status on console 0 changed to on > spurious 8259A interrupt: IRQ7. > Adding 891568k swap on /dev/sda9. Priority:-1 extents:1 > kjournald starting. Commit interval 5 seconds > EXT3 FS on sda5, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > ReiserFS: sda7: found reiserfs format "3.6" with standard journal > ReiserFS: sda7: using ordered data mode > ReiserFS: sda7: journal params: device sda7, size 8192, journal first block 18, > max trans len 1024, max batch 900, max commit age 30, max trans age 30 > ReiserFS: sda7: checking transaction log (sda7) > ReiserFS: sda7: Using r5 hash to sort names > ReiserFS: sda8: found reiserfs format "3.6" with standard journal > ReiserFS: sda8: using ordered data mode > ReiserFS: sda8: journal params: device sda8, size 8192, journal first block 18, > max trans len 1024, max batch 900, max commit age 30, max trans age 30 > ReiserFS: sda8: checking transaction log (sda8) > ReiserFS: sda8: Using r5 hash to sort names > parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] > parport0: irq 7 detected > lp0: using parport0 (polling). > ip_tables: (C) 2000-2002 Netfilter core team > ip_conntrack version 2.1 (4096 buckets, 32768 max) - 248 bytes per conntrack > bootsplash: status on console 0 changed to on > NET: Registered protocol family 23 > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > ACPI-0768: *** Warning: Thread 9F6 could not acquire Mutex [<NULL>] > AE_BAD_PARAMETER > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001 > usbcore: registered new driver usbfs > usbcore: registered new driver hub > USB Universal Host Controller Interface driver v2.3 > uhci_hcd 0000:00:11.2: UHCI Host Controller > uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1 > uhci_hcd 0000:00:11.2: irq 11, io base 0x0000d400 > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > uhci_hcd 0000:00:11.3: UHCI Host Controller > uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2 > uhci_hcd 0000:00:11.3: irq 11, io base 0x0000d800 > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 2 ports detected > uhci_hcd 0000:00:11.4: UHCI Host Controller > uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 3 > uhci_hcd 0000:00:11.4: irq 11, io base 0x0000dc00 > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 2 ports detected > Linux agpgart interface v0.101 (c) Dave Jones > agpgart: Detected VIA PM266/KM266 chipset > agpgart: AGP aperture is 64M @ 0xe0000000 > via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker > eth0: VIA Rhine II at 0x1d000, 00:07:95:46:91:f3, IRQ 9. > eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1. > usb 3-1: new full speed USB device using uhci_hcd and address 2 > PCI: Setting latency timer of device 0000:00:11.5 to 64 > BIOS EDD facility v0.16 2004-Jun-25, 1 devices found > eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 > IA-32 Microcode Update Driver: v1.14 <tigran@xxxxxxxxxxx> > IA-32 Microcode Update Driver v1.14 unregistered > bootsplash: status on console 0 changed to on > bootsplash: status on console 0 changed to on > > ------- You are receiving this mail because: ------- > You are on the CC list for the bug, or are watching someone who is. - : send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
