Hardware: Dual AthlonMP
Onboard LSI 1030 (system running for years w/ various
kernels..)
Output from a 2.4.29 kernel:
Fusion MPT base driver 2.05.16
Copyright (c) 1999-2004 LSI Logic Corporation
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator}
mptbase: Initiating ioc1 bringup
ioc1: 53C1030: Capabilities={Initiator}
mptbase: 2 MPT adapters found, 2 installed.
Fusion MPT SCSI Host driver 2.05.16
scsi0 : ioc0: LSI53C1030, FwRev=01000000h, Ports=1, MaxQ=255, IRQ=17
scsi1 : ioc1: LSI53C1030, FwRev=01000000h, Ports=1, MaxQ=255, IRQ=18
blk: queue f7bbca18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: SEAGATE Model: ULTRIUM06242-XXX Rev: 1528
Type: Sequential-Access ANSI SCSI revision: 03
blk: queue f7bbc818, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: SEAGATE Model: VIPER 2000 Rev: 0125
Type: Medium Changer ANSI SCSI revision: 02
blk: queue f7bbc618, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: SEAGATE Model: ST373207LW Rev: 0003
Type: Direct-Access ANSI SCSI revision: 03
blk: queue f7bbc218, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: SEAGATE Model: ST373207LW Rev: 0003
Type: Direct-Access ANSI SCSI revision: 03
blk: queue f7b3ee18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
st: Version 20040102, bufsize 32768, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi0, channel 0, id 6, lun 0
Attached scsi generic sg1 at scsi0, channel 0, id 6, lun 1, type 8
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
SCSI device sda: 143374744 512-byte hdwr sectors (73408 MB)
Partition check:
sda: sda1 sda2 sda3
SCSI device sdb: 143374744 512-byte hdwr sectors (73408 MB)
sdb: sdb1 sdb2
Running up to 2.6.14preXX (didn't test every kernel)
When booting 2.6.15 and 2.6.16pre1 I get: (written down, no logfile)
sd 1:0:0:0
command: Write (10): 2a 00 01 f8 11 e7 00 00 08 00
mptbase: ioc1: IOCStatus(0x0048): SCSI Task Terminated
mptscsih: ioc1: task abort: SUCCESS (sc=f6c5d8e0)
mptscsih: ioc: attempting task abort! (sc=f6c5e900)
..many times, till I press the reset button.
Any ideas?
GS
P.S.: More info available on request (what?)
--
Gerhard Schneider
Institute of Lightweight Design and e-Mail:gs@xxxxxxxxxxxxxxxxx
Structural Biomechanics (E317) Tel.: +43 1 58801 31716
Vienna University of Technology / Austria Fax: +43 1 58801 31799
A-1040 Wien, Gusshausstrasse 27-29 http://www.ilsb.tuwien.ac.at/~gs/
Attachment:
signature.asc
Description: OpenPGP digital signature
