Summarizing all this. There are two problems here. 1. reserifs4 panics when it gets io errors - I remember this was an issue that needed to be fixed in the R4 code before it moves to mainline... 2. Why does a drive which is fine with 2.6.15-rc5-mm3, return a -5 with 2.6.16-mm3 and above? Smart reports no problems with the drive hardware. What has changed in the libata/scsi stacks? Thanks, Ed Tomlinson On Saturday 21 January 2006 16:36, Ed Tomlinson wrote: > On Saturday 21 January 2006 13:45, Barry K. Nathan wrote: > > On 1/21/06, Ed Tomlinson <edt@xxxxxx> wrote: > > > grover:/var/log# smartctl -i -d ata /dev/sda > > [snip] > > > grover:/var/log# smartctl -H -d ata /dev/sda > > > smartctl version 5.34 [x86_64-unknown-linux-gnu] Copyright (C) 2002-5 Bruce Allen > > > Home page is http://smartmontools.sourceforge.net/ > > > > > > === START OF READ SMART DATA SECTION === > > > SMART overall-health self-assessment test result: PASSED > > > > > > --- > > > > > > Hope this helps and that I found the correct places to copy the info. > > > > How about: > > smartctl -a -d ata /dev/sdagrover:/poola/home/ed# smartctl -a -d ata /dev/sda > smartctl version 5.34 [x86_64-unknown-linux-gnu] Copyright (C) 2002-5 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF INFORMATION SECTION === > Device Model: Maxtor 6L250S0 > Serial Number: L50QDF3H > Firmware Version: BACE1G10 > User Capacity: 251,000,193,024 bytes > Device is: Not in smartctl database [for details use: -P showall] > ATA Version is: 7 > ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0 > Local Time is: Sat Jan 21 16:34:26 2006 EST > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x80) Offline data collection activity > was never started. > Auto Offline Data Collection: Enabled. > Self-test execution status: ( 0) The previous self-test routine completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: (1922) seconds. > Offline data collection > capabilities: (0x5b) SMART execute Offline immediate. > Auto Offline data collection on/off support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > No Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 99) minutes. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE > 3 Spin_Up_Time 0x0027 252 252 063 Pre-fail Always - 571 > 4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 2 > 5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0 > 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0 > 7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0 > 8 Seek_Time_Performance 0x0027 250 240 187 Pre-fail Always - 49844 > 9 Power_On_Hours 0x0032 251 251 000 Old_age Always - 49644 > 10 Spin_Retry_Count 0x002b 252 252 157 Pre-fail Always - 0 > 11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail Always - 0 > 12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always - 4 > 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0 > 193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0 > 194 Temperature_Celsius 0x0032 028 253 000 Old_age Always - 29 > 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 8656 > 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0 > 197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0 > 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0 > 199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0 > 200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0 > 201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 1 > 202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0 > 203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0 > 204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0 > 205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0 > 207 Spin_High_Current 0x002a 252 252 000 Old_age Always - 0 > 208 Spin_Buzz 0x002a 252 252 000 Old_age Always - 0 > 209 Offline_Seek_Performnce 0x0024 242 242 000 Old_age Offline - 143 > 210 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0 > 211 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0 > 212 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0 > > SMART Error Log Version: 1 > No Errors Logged > > SMART Self-test log structure revision number 1 > No self-tests have been logged. [To run self-tests, use: smartctl -t] > > > SMART Selective self-test log data structure revision number 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. > > > > or, if that produces too much output, then at least the following two: > > smartctl -A -d ata /dev/sda > > smartctl -l error -d ata /dev/sda > grover:/poola/home/ed# smartctl -l error -d ata /dev/sda > smartctl version 5.34 [x86_64-unknown-linux-gnu] Copyright (C) 2002-5 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF READ SMART DATA SECTION === > SMART Error Log Version: 1 > No Errors Logged > > > > That way we might be able to figure out whether the disk > > coincidentally started going bad after you updated the kernel. > > I suspect the newer kernel (or kernels) since when I revert to 15-rc5-mm3 all is well. > > Thanks, > Ed Tomlinson > - > : send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ > > - : send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
