qla1280.c broken on SGI visws, PCI coherency problem

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello,
since last week I'm trying to bring the current version of 2.6.12+ in working order on that almost abandoned SGI 320 Visual Workstation. This
beastlet also used have a QLA1080 as SCSI controller, which is actually
the only supported one to boot from.
I'm not sure if this is just a SGI320 problem (there seems to be two bus
bridges in use: PCI: Lithium bridge A bus: 1, bridge B (PIIX4) bus: 0)
or now a general problem for all platforms not implementing a mmiowb()
write barrier operation, but since 2.6.11 the qla1280.c driver gets
severly stuck after a few minutes of heavy use:

zapp kernel: qla1280: ISP invalid handle

and then usually the kernel hangs hard or the SCSI subsystem is
inoperable.
Last year Jesse Barnes published a patch introducing I/O space write barrier instructions especially for IA64 and MIPS multiprocessors. In that patch some PCI posted write flushs were replaced by mmiowb() (platform specific write barrier instruction), and at least for the SGI VisWS, this was one replacement too much.... I'm aware that the Visws PCI controller (at least the Lithium chip resp. for PCI 64 bus) reused parts from the O2 and sufferes the same problem of lacking cache coherency, but I wonder now if the qla1280.c is actually stable anymore in kernels after 2.6.10 (last version with the PCI write flushes in qla1280_64/32bit_start_scsi() ) and non-x86 platforms.

I've just tried qla1280.[ch] from a more recent version than 2.6.12.4,
namely 2.6.14.3, and have the same problem again (only worse, but there
has been some patches in qla1280.c regarding error recovery recently,
and now the kernel just hangs...), unless I add the one/two RD_REG_WORD()
lines again.
To repeat: Has there been any notion of problems with qla1280.c recently,
last known good version in 2.6.10 is from Xmas last year.

I can run tests also on a Intel dual PII server board with that QLA1080 HBA, but not now.

Regards, Michael

--- ../linux-2.6.14.3/drivers/scsi/qla1280.c-	2005-11-24 23:10:21.000000000 +0100
+++ ../linux-2.6.14.3/drivers/scsi/qla1280.c	2005-12-07 21:27:42.000000000 +0100
@@ -3236,6 +3236,7 @@
 	WRT_REG_WORD(&reg->mailbox4, ha->req_ring_index);
 	/* Enforce mmio write ordering; see comment in qla1280_isp_cmd(). */
 	mmiowb();
+	RD_REG_WORD(&reg->mailbox4);
 
  out:
 	if (status)
@@ -3504,6 +3505,7 @@
 	WRT_REG_WORD(&reg->mailbox4, ha->req_ring_index);
 	/* Enforce mmio write ordering; see comment in qla1280_isp_cmd(). */
 	mmiowb();
+	RD_REG_WORD(&reg->mailbox4);
 
 out:
 	if (status)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]
  Powered by Linux