Hi,
could someone explain me meaning of teh below debug messages?
The disk sdb went wrong because of bad media. However, I observe
weird scsi-card errors. We had to re-generate parity on RAID5 disks
in the array, although the disk which broke was NRAID disk:
Setting Global Tags= 32
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160B Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
blk: queue f73eaa18, I/O limit 524287Mb (mask 0x7fffffffff)
(scsi2:A:0): 160.000MB/s transfers (80.000MHz DT, offset 62, 16bit)
(scsi1:A:4): 80.000MB/s transfers (40.000MHz, offset 62, 16bit)
(scsi1:A:6): 20.000MB/s transfers (10.000MHz, offset 15, 16bit)
Vendor: QUANTUM Model: SuperDLT1 Rev: 4646
Type: Sequential-Access ANSI SCSI revision: 02
blk: queue f73ea818, I/O limit 524287Mb (mask 0x7fffffffff)
Vendor: OVERLAND Model: LXB Rev: 0106
Type: Medium Changer ANSI SCSI revision: 02
blk: queue f704f418, I/O limit 524287Mb (mask 0x7fffffffff)
Vendor: ADVUNI Model: OXYGENRAID 3000R Rev: 327J
Type: Direct-Access ANSI SCSI revision: 04
blk: queue f704fa18, I/O limit 524287Mb (mask 0x7fffffffff)
Vendor: ADVUNI Model: OXYGENRAID 3000R Rev: 327J
Type: Direct-Access ANSI SCSI revision: 04
blk: queue f73ea418, I/O limit 524287Mb (mask 0x7fffffffff)
Vendor: ADVUNI Model: OXYGENRAID 3000R Rev: 327J
Type: Direct-Access ANSI SCSI revision: 04
blk: queue f6fadc18, I/O limit 524287Mb (mask 0x7fffffffff)
Vendor: ADVUNI Model: OXYGENRAID 3000R Rev: 327J
Type: Direct-Access ANSI SCSI revision: 04
blk: queue f6fada18, I/O limit 524287Mb (mask 0x7fffffffff)
scsi2:A:0:0: Tagged Queuing enabled. Depth 32
scsi2:A:0:1: Tagged Queuing enabled. Depth 32
scsi2:A:0:2: Tagged Queuing enabled. Depth 32
scsi2:A:0:3: Tagged Queuing enabled. Depth 32
st: Version 20040102, bufsize 32768, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi1, channel 0, id 4, lun 0
Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 1
Attached scsi disk sdd at scsi2, channel 0, id 0, lun 2
Attached scsi disk sde at scsi2, channel 0, id 0, lun 3
SCSI device sdb: 245760000 512-byte hdwr sectors (125829 MB)
/dev/scsi/host2/bus0/target0/lun0: p1
SCSI device sdc: 40989184 512-byte hdwr sectors (20986 MB)
/dev/scsi/host2/bus0/target0/lun1: p1
SCSI device sdd: 1638400000 512-byte hdwr sectors (838861 MB)
/dev/scsi/host2/bus0/target0/lun2: p1
SCSI device sde: 651395072 512-byte hdwr sectors (333514 MB)
/dev/scsi/host2/bus0/target0/lun3: p1
The disk sdb1 went wrong because of bad media. However, I observe
weird scsi-card errors:
scsi1:0:4:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0x32 0x0
scsi1: At time of recovery, card was not paused
Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State in Message-out phase, at SEQADDR 0x36
Card was paused
ACCUM = 0xa0, SINDEX = 0x48, DINDEX = 0xe4, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x0
SCSIPHASE[0x4] SCSISIGI[0xb6] ERROR[0x0] SCSIBUSL[0x0]
LASTPHASE[0xa0] SCSISEQ[0x12] SBLKCTL[0xa] SCSIRATE[0x93]
SEQCTL[0x10] SEQ_FLAGS[0x40] SSTAT0[0x2] SSTAT1[0x11]
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8] SIMODE1[0xac]
SXFRCTL0[0x88] DFCNTRL[0x0] DFSTATUS[0x89]
STACK: 0x0 0x16a 0x17f 0x34
SCB count = 6
Kernel NEXTQSCB = 4
Card NEXTQSCB = 4
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0x40] SCB_SCSIID[0x47] SCB_LUN[0x0] SCB_TAG[0x3]
1 SCB_CONTROL[0xc0] SCB_SCSIID[0x67] SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
16 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
17 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
18 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
19 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
20 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
21 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
22 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
23 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
24 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
25 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
26 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
27 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
28 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
29 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
30 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
31 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
3 SCB_CONTROL[0x40] SCB_SCSIID[0x47] SCB_LUN[0x0]
Kernel Free SCB list: 5 2 1 0
Untagged Q(4): 3
DevQ(0:4:0): 0 waiting
DevQ(0:6:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:4:0: Device is active, asserting ATN
Recovery code sleeping
(scsi1:A:4:0): Abort Message Sent
(scsi1:A:4:0): SCB 3 - Abort Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 0x2002
scsi1:0:6:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0x32 0x0
Infinite interrupt loop, INTSTAT = 0scsi1: At time of recovery, card was not paused
Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x18
Card was paused
ACCUM = 0x3, SINDEX = 0x48, DINDEX = 0xe4, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x0
SCSIPHASE[0x0] SCSISIGI[0x18] ERROR[0x0] SCSIBUSL[0x0]
LASTPHASE[0x1] SCSISEQ[0x1a] SBLKCTL[0xa] SCSIRATE[0x0]
SEQCTL[0x10] SEQ_FLAGS[0xc0] SSTAT0[0x10] SSTAT1[0x8]
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8] SIMODE1[0xac]
SXFRCTL0[0x80] DFCNTRL[0x0] DFSTATUS[0x89]
STACK: 0xe8 0x16a 0x17f 0x17
SCB count = 6
Kernel NEXTQSCB = 5
Card NEXTQSCB = 5
QINFIFO entries:
Waiting Queue entries: 0:3
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0x40] SCB_SCSIID[0x67] SCB_LUN[0x0] SCB_TAG[0x3]
1 SCB_CONTROL[0xc0] SCB_SCSIID[0x47] SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
16 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
17 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
18 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
19 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
20 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
21 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
22 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
23 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
24 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
25 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
26 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
27 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
28 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
29 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
30 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
31 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
3 SCB_CONTROL[0x40] SCB_SCSIID[0x67] SCB_LUN[0x0]
Kernel Free SCB list: 4 2 1 0
Untagged Q(6): 3
DevQ(0:4:0): 0 waiting
DevQ(0:6:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:6:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
scsi1:0:6:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Infinite interrupt loop, INTSTAT = 0scsi1: At time of recovery, card was not paused
Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x18
Card was paused
ACCUM = 0x3, SINDEX = 0x48, DINDEX = 0xe4, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x0
SCSIPHASE[0x0] SCSISIGI[0x18] ERROR[0x0] SCSIBUSL[0x0]
LASTPHASE[0x1] SCSISEQ[0x1a] SBLKCTL[0xa] SCSIRATE[0x0]
SEQCTL[0x10] SEQ_FLAGS[0xc0] SSTAT0[0x10] SSTAT1[0x8]
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8] SIMODE1[0xac]
SXFRCTL0[0x80] DFCNTRL[0x0] DFSTATUS[0x89]
STACK: 0xe8 0x16a 0x17f 0x17
SCB count = 6
Kernel NEXTQSCB = 3
Card NEXTQSCB = 5
QINFIFO entries: 5
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0x0] SCB_SCSIID[0x67] SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0xc0] SCB_SCSIID[0x47] SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
16 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
17 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
18 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
19 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
20 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
21 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
22 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
23 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
24 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
25 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
26 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
27 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
28 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
29 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
30 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
31 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
5 SCB_CONTROL[0x40] SCB_SCSIID[0x67] SCB_LUN[0x0]
Kernel Free SCB list: 4 2 1 0
Untagged Q(6): 5
DevQ(0:4:0): 0 waiting
DevQ(0:6:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:6:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
scsi1:0:6:0: Attempting to queue a TARGET RESET message
CDB: 0x12 0x0 0x0 0x0 0x32 0x0
scsi1:0:6:0: Command not found
aic7xxx_dev_reset returns 0x2002
scsi1:0:6:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Infinite interrupt loop, INTSTAT = 0scsi1: At time of recovery, card was not paused
Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x18
Card was paused
ACCUM = 0x3, SINDEX = 0x48, DINDEX = 0xe4, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x0
SCSIPHASE[0x0] SCSISIGI[0x18] ERROR[0x0] SCSIBUSL[0x0]
LASTPHASE[0x1] SCSISEQ[0x1a] SBLKCTL[0xa] SCSIRATE[0x0]
SEQCTL[0x10] SEQ_FLAGS[0xc0] SSTAT0[0x10] SSTAT1[0x8]
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8] SIMODE1[0xac]
SXFRCTL0[0x80] DFCNTRL[0x0] DFSTATUS[0x89]
STACK: 0xe8 0x16a 0x17f 0x17
SCB count = 6
Kernel NEXTQSCB = 5
Card NEXTQSCB = 3
QINFIFO entries: 3
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0x0] SCB_SCSIID[0x67] SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0xc0] SCB_SCSIID[0x47] SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
16 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
17 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
18 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
19 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
20 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
21 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
22 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
23 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
24 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
25 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
26 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
27 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
28 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
29 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
30 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
31 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
3 SCB_CONTROL[0x40] SCB_SCSIID[0x67] SCB_LUN[0x0]
Kernel Free SCB list: 4 2 1 0
Untagged Q(6): 3
DevQ(0:4:0): 0 waiting
DevQ(0:6:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:6:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
# lspci
0000:00:00.0 Host bridge: Intel Corporation E7501 Memory Controller Hub (rev 01)ernel-headers=/usr/src/linux-2.4.30-pre2-bk3 -
0000:00:00.1 Class ff00: Intel Corporation E7500/E7501 Host RASUM Controller (rev 01)-new-config --enable-debug-kernel --enabl
0000:00:03.0 PCI bridge: Intel Corporation E7500/E7501 Hub Interface C PCI-to-PCI Bridge (rev 01)
0000:00:03.1 Class ff00: Intel Corporation E7500/E7501 Hub Interface C RASUM Controller (rev 01)
0000:00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #1) (rev 02)
0000:00:1d.1 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #2) (rev 02)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 42)
0000:00:1f.0 ISA bridge: Intel Corporation 82801CA LPC Interface Controller (rev 02)
0000:00:1f.1 IDE interface: Intel Corporation 82801CA Ultra ATA Storage Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corporation 82801CA/CAM SMBus Controller (rev 02)
0000:01:0c.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
0000:02:1c.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04)
0000:02:1d.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev 04)
0000:02:1e.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04)
0000:02:1f.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev 04)
0000:03:07.0 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
0000:03:07.1 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
0000:03:08.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
0000:04:08.0 RAID bus controller: Intel Corporation RAID Controller
0000:04:09.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: Intel Model: Host Drive #00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 02 Id: 06 Lun: 00
Vendor: ESG-SHV Model: SCA HSBP M16 Rev: 0.05
Type: Processor ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 04 Lun: 00
Vendor: QUANTUM Model: SuperDLT1 Rev: 4646
Type: Sequential-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 06 Lun: 00
Vendor: OVERLAND Model: LXB Rev: 0106
Type: Medium Changer ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: ADVUNI Model: OXYGENRAID 3000R Rev: 327J
Type: Direct-Access ANSI SCSI revision: 04
Host: scsi2 Channel: 00 Id: 00 Lun: 01
Vendor: ADVUNI Model: OXYGENRAID 3000R Rev: 327J
Type: Direct-Access ANSI SCSI revision: 04
Host: scsi2 Channel: 00 Id: 00 Lun: 02
Vendor: ADVUNI Model: OXYGENRAID 3000R Rev: 327J
Type: Direct-Access ANSI SCSI revision: 04
Host: scsi2 Channel: 00 Id: 00 Lun: 03
Vendor: ADVUNI Model: OXYGENRAID 3000R Rev: 327J
Type: Direct-Access ANSI SCSI revision: 04
#
# uname -a
Linux oxygen 2.4.30-pre2-bk3 #3 SMP Mon Mar 7 13:35:40 MET 2005 i686 Intel(R) Xeon(TM) CPU 3.06GHz GenuineIntel GNU/Linux
Thanks for help
Martin
-
: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
