On Mon, Oct 09, 2017 at 02:37:14AM +0530, Anand Moon wrote: > Hi Krzysztof, > > On 8 October 2017 at 21:20, Krzysztof Kozlowski <krzk@xxxxxxxxxx> wrote: > > On Sun, Oct 08, 2017 at 06:11:12PM +0530, Anand Moon wrote: > >> Hi Krzysztof, > >> > >> On 6 October 2017 at 12:12, Krzysztof Kozlowski <krzk@xxxxxxxxxx> wrote: > >> > On Fri, Oct 6, 2017 at 6:36 AM, Anand Moon <linux.amoon@xxxxxxxxx> wrote: > >> >> remove the disable and enable of phy clk. > >> >> phy clk is needed to tune the phy controller. > >> > > >> > Drivers should in general enable and disable the clocks they use. Just > >> > like in patch #1 please describe why you are doing this, what kind of > >> > problem are you trying to solve and what exactly are you trying to do > >> > here. > >> > > >> > BR, > >> > Krzysztof > >> > > >> > >> [snip] > >> > >> Usually we would disable the clk on error patch and return with failed. > >> but in the current code we disable the clk in init routine and > >> enable the clk in disable routine which seem incorrect. > > > > No. For example for exynos5_usbdrd_phy_exit() the driver enables the > > clock only for the access to PHY block (PHY registers). > > > > But I dont get it why we disable code phy clk, which could be used in > future phy tune or link control as it part of CLK_FSYS. Clock is being disabled when it is not used. AFAIU, current code follows this logic. > > >> > >> [0] https://github.com/torvalds/linux/blob/master/drivers/phy/samsung/phy-exynos5-usbdrd.c#L362-L412 > >> [1] https://github.com/torvalds/linux/blob/master/drivers/phy/samsung/phy-exynos5-usbdrd.c#L424-L446 > >> > >> On 3.10.x kernel clk_summary all the clk are enables. > >> > >> mout_usbdrd300 3 3 24000000 > >> dout_usbdrd300 2 2 24000000 > >> sclk_usbdrd300 1 1 24000000 > >> dout_usbphy300 2 2 24000000 > >> sclk_usbphy300 1 1 24000000 > >> mout_usbdrd301 3 3 24000000 > >> dout_usbdrd301 2 2 24000000 > >> sclk_usbdrd301 1 1 24000000 > >> dout_usbphy301 2 2 24000000 > >> sclk_usbphy301 1 1 24000000 > >> > >> Some more changes in clk driver might be required to stabilize the usb module. > > > > Please describe the issues with stability first. > > > > Best regards, > > Krzysztof > > > On stability: > > USB 3.0 read / write performance is not up to mark with moderate data > read / write speed, > If you give long compilation of kernel or any source code it would > likely be slow > It work pretty good with USB 3.0 SSD but generally failed with 2.5' inc HDD. > > If needed I will share you some performance test result with and > without these patches. Yes, such results are essential for this (and any) commit. Best regards, Krzysztof > > I have some more changes related to usbdrd phy change queued along this on. > > Best Regards > -Anand -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |